BeaverLAB DDL-G1A Manuale utente
BeaverLAB Electric Glue Gun
DDL-G1A/B Instructions
01 Product Introduction
Please read this manual carefully before using the product and keep it
properly.
2
6
8
3
7
4
5
Protective cap of glue gun
Status indicator
Lanyard
Switch key
Glue trigger
Glue gun nozzle
Rubber inlet
Type-C power supply port
1
1 2 3
4 5 6
7 8
02 Instructions
This product is suitable for 7mm hot-melt adhesive stick, please do not
insert hot-melt adhesive stick of other specifications.
Corded version：Be sure to select appropriate power supply (power supply
voltage DC5V, power supply current ≥ 2A)
(Mobile phone charger and charging treasure can be used). Connect the glue
gun to the power supply equipment with the power supply cable.
Battery version：Please ensure that the equipment has sufficient power
In the shutdown state, press and hold the switch button for 2S to start
the product.
When the machine is turned on, long press the switch button for 2s to
turn off the product.
If the product is not used for any operation within 3 minutes, the product
will automatically shut down.
Insert the glue stick, after starting the product, wait for the green light of the
indicator to be on (the waiting time is about 30 s), after the pre heating is
completed, press the trigger to release the glue.
Apply the hot melt adhesive to the object to be bonded, press it for a period
of time, and the bonding is completed after the hot melt adhesive has solidified.
You can use the mobile phone charger, power bank, computer USB interface
and other power supplies that can output 5V DC voltage to charge this product.
ON-OFF
Usage method
Charging (applicable to lithium battery version)※
If the product has not been used for a long time, please fully charge the product
Indicator Status
Indicator Status
Indicator Status Product status
Green Fashing Heating
Green Bright Can Work
Flash Red Light Low Battery（Battery version）
Red Slow Flashing Charging（Battery version）
The red light stays on for 3 minutes
and then goes out
Charging completed
（Battery version）
Be sure to take off the protective cap of the glue gun before use.
The nozzle temperature of the glue gun is high during operation, please do not touch.
The temperature of hot melt adhesive in molten state is very high, please do not
touch.
If the melted hot melt adhesive drops on the skin, please wipe it off immediately
and wash it with cold water immediately.
Lithium battery version products are not fully charged when leaving the factory,
and should be fully charged before the first use.
Lithium battery version products do not support charging while using.
When inserting the glue stick for the first time/replacing the glue stick, please
insert the glue stick forcefully, and release when the motor is tightly held for
conveying.
Do not forcibly pull out the glue stick before it is used up to avoid damaging
the product
Tips
Attention
before use.
Wired version, plug and play.
If not in use, please stand or hang the product.
This product is only applicable to the glue stick with a diameter of 7mm.
03 General faults and troubleshooting
It is prohibited to place the product in a high temperature environment for a long
time. If the product is not used for a long time, please place the product in a normal
temperature and humidity environment, and charge the product once every six
months.
Please do not smash this product to avoid damaging the internal components.
Maintenance
Troubleshooting
Fault Reason Exclusion method
Product does not work
Charge out Use after charging
Automatic shutdown Restart the product
Internal circuit damage Need repair
Glue stick cannot be
squeezed out
Glue stick is used up Insert new glue stick
Internal blockage Need repair
Unable to charge Internal circuit damage Need repair
The lithium battery version has not been used for a long time. If the status indicator
does not display normally during recharging, please keep charging for 30 minutes
before observing.
BeaverLAB electric glue gun performance fault table
Name Fault content
BeaverLAB electric
glue gun
1.Unable to charge normally（Battery version）.
2.The indicator cannot be displayed normally.
3.The key cannot be used normally.
4.he shell of the body is damaged due to structural
or material factors without human reason.
Product Model：DDL-G1B Rated Voltage：DC 5V
Battery Capacity：2000mAh Preheating Time：About 45s
Charging Voltage: 5V 1A Glue Stick Diameter：7mm
Glue Stick Length：125mm Charging time：3-4 h
Product Model：DDL-G1A Glue Stick Length：125mm Product Model：DDL-G1A Glue Stick Length：125mm
Preheating Time：About 45s Power Supply：DC5V 2A（≥2A）
Glue Stick Diameter：7mm
BeaverLAB Electric Glue Gun
Corded version：
Battery version：
Executive Standards：GB 4706.1-2005
Official Website: www.dangdangli.com
Manufacturer: Beaver Technology (Shenzhen) Co.Ltd
Address: F518 Fashion Creative Park,Xixiang Street,Baoan District Shenzhen
E-mail: [email protected]
Questo manuale è adatto per i seguenti modelli
1
Indice
