Behringer DCX Series Manuale utente

Altri manuali per DCX Series

1

Altri manuali Behringer Hardware per computer

Behringer

Behringer Ultravoice Digital VX2496 Manuale utente

Behringer

Behringer ULTRA-DI PRO DI4000 Manuale utente

Behringer

Behringer Ultracurve Pro DEQ2496 Manuale utente

Behringer

Behringer MINIFEX FEX800 Manuale utente

Behringer

Behringer ULTRAMIZER PRO DSP1400P Manuale utente

Behringer

Behringer ABACUS Manuale utente

Behringer

Behringer SHARK FBQ100 Manuale utente

Behringer

Behringer MODULIZER PRO DSP1224P Manuale utente

Behringer

Behringer Eurolive B1520 Pro Manuale utente

Behringer

Behringer Ultra-Voice VX2000 Manuale utente

Behringer

Behringer SU9920 Manuale utente

Behringer

Behringer BASS V-AMP LX1B Manuale utente

Behringer

Behringer SU9920 Manuale utente

Behringer

Behringer Ultra-Voice VX2000 Manuale utente

Behringer

Behringer MINIFEX FEX800 Manuale utente

Behringer

Behringer X-DANTE Manuale utente

Behringer

Behringer Sonic Exciter SX3040 Manuale utente

Behringer

Behringer Sonic Exciter SX3040 Manuale utente

Behringer

Behringer Virtualizer Pro DSP1024P Manuale utente

Behringer

Behringer Sonic Exciter SX3040 Manuale utente

Behringer

Behringer Tube Ultra-Q T1951 Manuale utente

Behringer

Behringer WING-DANTE Manuale utente

Behringer

Behringer ULTRADRIVE PRO DCX2496 Manuale utente

Behringer

Behringer Ultra-dyne Pro DSP9024 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

1

BehringerMods.com

Instructions for modification of Behringer DCX analog

inputs and outputs

The following instructions will cover the details of

modifying a DCX for upgraded analog outputs 1- and

analog inputs A & B (input C excluded).

These modifications require a high level of experience

with electronics. If you doubt your ability to complete

the mods correctly, please contact BehringerMods to

arrange an installation service.

BehringerMods take no responsibility for damage

caused to your equipment by modification.

2

The modification package should come with the following parts:

•Analog input and output upgrade PCB

•Link PCB

•Ribbon Cable x2

•PCB Stands x4

Upgrade PCB Link PCB

3

Get a cup of tea or coffee. Remove the equipment cover and keep the

screws in a dish.

Use pointy nosed pliers to gently remove the glue securing the main ribbon

and smaller ribbon cable connecting the rear PCB to the main PCB.

Remove all screws that secure the rear PCB to the case.

Remove the rear PCB from the case.

4

Locate and remove capacitors C2 , C27, C41, C42

Do not damage the PCB, it is delicate.

Tip: Apply new solder to the capacitor legs. Heat one leg until solder is fully

melted, then lean the capacitor to one side pulling the leg partially from

the PCB. Heat the other leg and lean capacitor the other way. Repeat

process until the capacitor is free from the PCB.

Cut the legs of pins 2 and 3 on output XLRs 1- .

Tip: I ma e two cuts, to leave a clear gap.

If you loo inside the front of the soc et, the pins are numbered.

5

Clear solder from the positive pads (round holes, not square) with a solder

sucker or solder wick.

We will connect wires here.

Solder IDC 2 ribbon lines:

Line 18 (Orange) to C41

Line 17 (Yellow) to C2

Line 1 (Green) to C42

Line 15 (Blue) to C27

(Line 1 is blac on the far side of the ribbon, Line 20 is brown. If the ribbon is

not colour coded line 1 has a red stripe)

Line 1 Line 20

7

Solder IDC 2 Lines:

Line 1 to Bottom of C4

Line 2 to Bottom of C3

Solder IDC 2 Lines:

Line 3 (Gray) to XLR 3 - Pin 3

Line 4 (Violet) to XLR 3 - Pin 2

Line 5 (Blue) to XLR 2 - Pin 3

Line (Green) to XLR 2 - Pin 2

Line 7 (Yellow) to XLR 1 – Pin 3

Line 8 (Orange) to XLR 1 – Pin 2

Line 9 (Brown) to XLR – Pin 2

Line 10 (Red) to XLR – Pin 3

Line 11 (Black) to XLR 5 – Pin 2

Line 12 (White) to XLR 5 – Pin 3

Line 13 Gray) to XLR 4 – Pin 2

Line 14 (Violet) to XLR 4 – Pin 3

Line 3

Line 4

Line 5

Line 6

Line 7

Line 8

Line 9

Line 10

Line 11

Line 12

Line 13

Line 14

8

On the Main PCB (not rear PCB)

Remove SMD capacitors C88, C87.

Leave the gap open circuit.

Re-install the rear PCB.

Install the upgrade PCB with self adhesive feet.

9

Connect the Link PCB to the Main PCB ribbon socket.

Tip: Ensure the plug is central. It is possible to place it 1 pin sideways.

Connect the Main ribbon from Rear PCB to the Link PCB.

10

Also re-connect the smaller Rear PCB ribbon.

Upgrades are now complete!

If you removed the ribbon plug from the Upgrade PCB. The ‘Bump’ on the

ribbon plug faces the centre of the PCB on both IDC1 and IDC 2.

Unfortunately due to my mista e there was not space for a full size soc et

body.