BELINEA 1945 G1 Manuale utente

ENGLISH

Belinea 1945 G1 - Operating Instructions - 1

INTRODUCTION

This manual will familiarize you with the installation

and use of your Belinea monitor. Please take the time

to look through these instructions even if you are fa-

miliar with monitors.

We have taken all possible care to ensure that this

manual contains correct and accurate information.

However the manufacturer cannot assume liability for

any possible errors. In addition, the manufacturer can-

not guarantee that the hardware will meet the pur-

pose you require. We would appreciate reports of any

errors, suggestions or criticism.

MAXDATA Systeme GmbH,

45768 Marl, Germany,

www.maxdata.com

Editing, DTP and translation by Linguagem, www.Lin-

guagem.de.

produced, processed or distributed in any form (print,

photocopy, microfilm or any other process) or proc-

essed, duplicated or distributed by an electronic sys-

tem without prior written permission from the

manufacturer.

We reserve the right to make changes according to

the technical progress. Belinea is an internationally

registered trademark. Other brand names may be reg-

istered trademarks and must be treated as such.

Environment protection

We are all responsible for the environment: As many

of our customers are already familiar with monitors

we have not printed this manual in order to save paper

and by this protect our environment. Help to protect

the environment and only print the pages you need.

TABLE OF CONTENTS

INTRODUCTION...................................................... 1

IMPORTANT INFORMATION ................................... 2

UNPACKING ............................................................. 2

MOUNTING .............................................................. 3

CONNECTION .......................................................... 3

START UP ................................................................. 3

ERGONOMICS ......................................................... 4

CONFIGURATION..................................................... 4

SETTINGS................................................................. 5

CARING FOR YOUR MONITOR ............................... 7

TROUBLESHOOTING............................................... 8

TECHNICAL SPECIFICATIONS................................. 9

MAXDATA WARRANTY ........................................... 9

Guide to symbols

The symbols below are used in this manual to indicate

where there is risk of injury or damaging devices or to

indicate specially useful information.

DANGER! Indicates risk of injury. When not

following the instructions, severe injury or

death may result.

ATTENTION! Indicates possible damage to de-

vices. When not following instructions, devic-

es may be heavily damaged.

IMPORTANT! Indicates hints on operation and

other useful information.

ENGLISH

Belinea 1945 G1 - Operating Instructions - 2

IMPORTANT INFORMATION

Note on monitor placement

• The setup location must not be extremely hot,

cold, humid or dusty. Heat and cold can impair

the functionality of the monitor. Humidity and

dust can cause the monitor to fail.

• Do not place the monitor near heat sources

such as heaters or radiators. Do not expose

the monitor to mechanical vibrations or jarring.

Notes on power connection

Only use the power cord designated for use in

your country.

The wall outlet should be within easy reach.

Pulling the power plug is the only way to dis-

connect the monitor from the power source.

This monitor is ENERGY STAR®-compatible.

MAXDATA is an ENERGY STAR®- partner and

guarantees that this monitor complies with the

ENERGY STAR®guidelines for optimising

power consumption.

Safety instructions for operation

The power cord must not be damaged. Do not

place any objects on the power cord and make

sure it does not have any knots. To unplug the

cord, always pull on the plug and not on the ca-

ble itself. Damage to the power cord may re-

sult in fire or cause electric shocks.

• Avoid covering the ventilation slots. Air circula-

tion is necessary to prevent the monitor from

overheating. If the air circulation is restricted, it

could cause fire or damage the monitor.

• Do not use any solvents to clean the monitor,

as the housing could be damaged. For more in-

formation about cleaning the monitor see sec-

tion “Caring for your monitor” on page7.

Make sure that no humidity or liquids can enter

the monitor.

Never open the monitor housing yourself.

There is a danger of electric shocks and other

hazards. The monitor may only be opened and

services by qualified professionals.

UNPACKING

Scope of supply

Check if the delivery is complete.

1 Monitor

2 Instructions

3CD

4 Power cord

5 Audio cable

6 VGA cable

7 DVI cable (option)

Handling the monitor

Carefully lift the monitor out of the packaging.

• The monitor's LCD screen surface is very sen-

sitive! Please avoid any pressure on the sur-

face (finger, pencil etc.) and be especially

cautious during transportation since jolts and

shocks can cause the screen to become

scratched (always use the original packaging).

Keep the original box and packaging material in case

you have to ship or transport the monitor.

Intended purpose

This monitor developed as a display for computers.

12 34

56 7

ENGLISH

Belinea 1945 G1 - Operating Instructions - 3

MOUNTING

Mounting on the base

Only remove the safety pin from the back of

the base, if the monitor stands firmly on the

base.

Insert the shaft into the base until it locks in.

Wall mounting

The monitor is shipped with the standard desktop

configuration. However, you can optionally mount the

device on a wall or on a monitor swivel arm (optional

accessory). For mounting remove the screws from

the back of the monitor (4 screws). Use a VESA com-

patible support (4-hole assembly of 100 x 100 mm ac-

cording the international VESA FDMI standard) and

follow the corresponding instructions.

CONNECTION

1 Make sure that the monitor and the PC are

disconnected from the mains supply.

Connecting to an analogue graphics

card

You can connect the monitor to an analogue graphic

board or to a digital graphics card.

Connect the plugs carefully in order not to

bend the pins.

1 Connect the supplied signal cable to the socket D-

SUB.

2 Connect the other end of the signal cable to the

output socket of your graphics card.

Connecting to a digital graphics card

1 Connect the optional signal cable to the socket

DVI.

2 Connect the other end of the signal cable to the

output socket of your graphics card.

Audio connection

If you PC has a separate audio output, use the audio

cable to connect the monitor to the PC.

1 Connect the supplied audio cable to the socket

AUDIO IN.

2 Plug the other end of the audio cable into the

output socket on the PC.

Mains connection

1 Connect the supplied power cable to the socket

AC IN.

2 Plug the other end of the power cable into a

grounded wall outlet.

3 Reconnect your PC to the mains supply.

START UP

1 Switch your PC on.

2 Press the button [ ] on the front of the monitor.

The status indicator beside the button [ ] lights up

green or orange.

Green = monitor active

Orange = monitor on stand-by (power save mode).

DVI

VGA

D-SUBDVIAUDIO IN

AUDIO

ENGLISH

Belinea 1945 G1 - Operating Instructions - 4

ERGONOMICS

The best alignment

Align the monitor in such a way, that distance and an-

gle correspond to the figure.

The best height

To adjust the height of the monitor, remove

the metal pin on the back of the base. Make

sure that the monitor stands firmly on the base, when

removing the pin.

Ergonomically, your posture is best when elbows, pel-

vis, knees and ankles are all at right angles.

Furthermore, you should regularly focus on an object

around 6 m away from you to help your eyes relax.

Putting the monitor in upright position

If needed, you can turn the monitor so that the screen

is in an upright position (Pivot function). Use the soft-

ware settings to adapt the picture accordingly.

Non-reflecting operation

Adjust the monitor so that there are no reflections of

direct sunlight or direct light on the screen. By this,

you protect your eyes from excessive strain.

This monitor meets the requirements for non-reflec-

tion. This makes it suitable for normal office applica-

tions and you do not need to take any special

additional measures.

CONFIGURATION

Windows®9x/ME/2,000 and XP

If using the monitor under Windows®9x/ME/2000

and XP, we strongly recommend installing the Belinea

configuration file. You can obtain this file from your

Belinea dealer or download it from the MAXDATA FTP

server at ftp.maxdata.com. Here click the

"Belinea_Treiber_Driver" directory and download the

Belinea.inf and README_Belinea.TXT files. Follow

the instructions in the README-Belinea.TXT file.

Windows®NT 4.0

Under Windows®NT 4.0 no separate setup file is re-

quired. Select the vertical frequency and the number

of colours directly on your PC within the "Start” J

“Settings” J“Control Panel” J“Display” J“Set-

tings” menu.

~70

90°

ca. 35° 60°

ENGLISH

Belinea 1945 G1 - Operating Instructions - 5

SETTINGS

Settings using the keys on the

monitor

You can make some adjustments directly using the

keys on the monitor (hot key function).

Automatic setting

Use this function to automatically adjust the individual

image parameters (brightness, contrast, image posi-

tion, phase etc.) to the optimum values for the current

graphic mode.

1 To start the automatic adjustment press the key

[].

Wait until the automatic adjustment is completed.

Brightness

Use this function to adjust the brightness directly us-

ing the keys on the monitor.

1 Press the key [ ].

2 Press the key [ ] or [ ] until the desired

brightness is set.

3 Press the key [ ] to quit the menu.

Contrast

Use this function to adjust the contrast directly using

the keys on the monitor.

1 Press the key [ ].

2 Press the key [ ] or [ ] until the desired

contrast is set.

3 Press the key [ ] to quit the menu.

Lock power key

Use this function to lock the on/off key of the monitor.

This prevents, unauthorised people to switch the

monitor off.

1 Press the key [ ] and keep it pressed.

Additionally, press the key [ ].

2 Keep both keys pressed until the process bar is

completed (approximately 10 seconds).

3 To unlock the key, repeat the steps 1 and 2.

Lock on screen display (OSD)

Use this function to lock the on screen menu (OSD) of

the monitor. This prevents unauthorised people to

change the settings. The power key will remain un-

locked.

1 Press the key [ ] and keep it pressed.

Additionally, press the key [ ].

2 Keep both keys pressed until the process bar is

completed (approximately 10 seconds).

3 To unlock the key, repeat the steps 1 and 2.

Mute

Use this function to switch the loudspeakers of the

monitor off.

1 Press the key [ ] and keep it pressed.

Additionally, press the key [ ].

2 To unlock the key, repeat step 1.

Settings using the OSD menu

The individual settings of the monitor can be made in

the on screen display (OSD).

ENGLISH

Belinea 1945 G1 - Operating Instructions - 6

Open the OSD menu

1 Press the key [ ] to open the OSD menu.

2 Press the key [ ] or [ ] to select the desired

sub menu.

3 Press the key [ ] to open the desired menu or

the desired function.

4 In further sub-menus proceed correspondingly.

5 After you have made the desired adjustment,

press [ ] of save the setting and quit the menu.

In some cases you have to press the key [ ]

several times.

Display current settings

Use this function to show the current settings.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

Automatic setting

Use this function to automatically adjust the individual

image parameters (brightness, contrast, image posi-

tion, phase etc.) to the optimum values for the current

graphic mode.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

The automatic adjustment is executed at each switch

on of the monitor.

Adaptation to the graphics card

If this function is switched on, the image parameters

are adapted automatically, if the settings are changed

on the PC.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Select the desired setting.

Adaptation to the input signal

With this function the monitor is automatically set to

the input signal (digital or analogue). You can use the

digital or analogue input at the same time.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Select the desired setting.

Set contrast and brightness

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Press the key [ ] or [ ] until the desired

contrast is set.

4 Press the key [ ] to change to the menu

brightness.

5 Press the key [ ] or [ ] until the desired

brightness is set.

If you have selected the colour setting sRGB

(standard RGB), the contrast cannot be set.

Colour control

The monitor offers 3 preset modes of colour settings.

Additionally, a separate mode allowing individual set-

ting of each colour channel is available.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select the desired setting.

sRGB = standard Windows setting

Warm = warm colours

Cold = cool colours

User defined = individual setting for Red/Green/Blue.

Use the key [ ] or [ ] to set the colour channels.

Set image width

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

width is set.

Set image position

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

horizontal position is set.

6 Press the key [ ] to change to the menu vertical

position.

7 Press the key [ ] or [ ] until the desired

vertical position is set.

Fine adjustment

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

adjustment is set.

To achieve best results, make the adjustment on a

white background with horizontal and vertical black

lines.

ENGLISH

Belinea 1945 G1 - Operating Instructions - 7

Set image sharpness

All resolutions provided by the graphics card that devi-

ated from the physical resolution of the monitor are in-

terpolated. This may impair the quality of the image.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

adjustment is set.

If the resolution of the graphics card is set to

the standard resolution of the monitor, the

sharpness cannot be adapted.

Language selection

This function selects the language of the OSD menu.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

vertical position is set.

Resolution notice

If this function is active, a message indicates if the

resolution and frequency are not optimally set to the

monitor.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

adjustment is set.

Make the necessary adjustments in the settings of

your PC, if this message is displayed.

OSD Position

This function sets the position of the OSD menu.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

position is set.

OSD switch off time

This function sets the time for which the OSD menu

will be displayed.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired time

is set.

Set volume

This function sets the volume.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select the upper key [ ].

4 Press the key [ ].

5 Press the key [ ] or [ ] until the desired

volume is set.

Switch sound off (MUTE)

Use this function to switch the loudspeakers of the

monitor off.

1 Open the OSD menu and select [ ].

2 Press the key [ ].

3 Select the lower key [ ].

4 Press the key [ ].

Restore default

1 Open the OSD menu and select [ ].

2 Press the key [ ].

Resolution and frequency

To allow fatigue free working the horizontal and verti-

cal image frequency must match. Make the necessary

adjustments in the settings of your PC.

For this monitor, we recommend a resolution of 1280

x 1024 at a frequency of 60 Hz.

CARING FOR YOUR MONITOR

The screen of the monitor is covered with an anti-re-

flex coating. Keep the screen clean to ensure full func-

tionality. Clean the surface very cautiously using a soft

cloth only as otherwise the coating may be damaged.

If the housing is very dirty, clean it using a cloth.

ENGLISH

Belinea 1945 G1 - Operating Instructions - 8

No humidity into the monitor! Before cleaning

the monitor pull the power cord and make sure

no liquids can enter the monitor when clean-

ing.

Do not use any solvents to clean the monitor, as the

housing could be damaged.

If only moderately dirty use a dry, soft antistatic cloth

to clean the monitor.

Disposal

This product is subject to the European

guideline 2002/96/EC.

All electric and electronic devices must be disposed of

separately from household waste at publicly estab-

lished facilities.

Avoid hazard to the environment and dangers to your

personal health by disposing the device properly.

For general information about the proper disposal,

contact the relevant local government department,

the disposal facility or the shop where you bought the

device.

Belinea monitors are designed for eco-

friendly recycling according to TCO. For all

questions concerning the disposal of your

monitor, also contact our recycling partner

for Europe and visit the web site http://

LQP2.de.hellmann.net/monitor-recycling.

Hellmann Process Management GmbH & Co. KG

Adolf-Köhne-Str. 11

49090 Osnabrück, Deutschland

Tel.: +49 (0) 541 605 1585

TROUBLESHOOTING

Bland screen

Power indicator is off

- Make sure the power cable and the power adapter

are connected properly. (See “Connection” on page

3.)

- Make sure that the monitor was turned on using the

power switch. (See “Start up” on page 3.)

Power indicator lights orange

- Is a power saving mode active?

Power indicator lights green

- A screen saver may be installed on your PC and was

automatically activated after a certain period of inactiv-

ity.

Press a key on your keyboard or move the mouse.

Message "No Signal"

- Is the signal cable connected to the monitor and the

PC's graphic port? (See “Connection” on page 3.)

- Is the PC turned on (see your PC's documentation)?

Display problems

Image is displaced to the left/right or to the

top/bottom

- If the image appears normal but off-centre, you can

adjust it using the OSD functions. (See “Automatic

setting” on page 5.)

Image flickers or is shaky

- Perhaps the setup file chosen for the monitor is in-

correct. (See “Configuration” on page 4.)

Image is blurred

- Check the sharpness settings. (See “Set image

sharpness” on page 7.)

- Check the brightness and contrast settings. (See

“Set contrast and brightness” on page 6.)

Colour problems

- If the colours are off (e.g. white is not really displayed

as white etc.), you should adjust the colour tempera-

ture. (See “Colour control” on page 6.)

ENGLISH

Belinea 1945 G1 - Operating Instructions - 9

TECHNICAL SPECIFICATIONS

MAXDATA WARRANTY

Belinea Premium Service

The three-year return to base warranty for your Belin-

ea monitor includes all parts and labour. In additions

many countries offer a free of charge swap out war-

ranty programme. This does not affect your Statutory

Rights.

For further information on the warranty or service,

please visit http://www.belinea.com or contact the

phone numbers listed in the enclosed short guide.

Please have the serial and model number ready when

calling.

Definitions Maxdata Warranty

The explanations below apply to all Belinea monitors.

The MAXDATA warranty covers all failures resulting

from defective components and manufacturing de-

fects that occur within the product specific warranty

period. The warranty period begins on the date of pur-

chase (date of original customer invoice).

Please be aware the in order to maintain the warranty

claim the product concerned has to be received by

MAXDATA together with the serial number and a

copy of the original customer invoice within the war-

ranty period.

MAXDATA's obligation under the warranty is restrict-

ed to repairing or exchanging defective components.

Defective components removed during repair process

become the property of MAXDATA. Components re-

placed within the warranty coverage assume the re-

maining valid warranty period of the system.

MAXDATA's obligation under the warranty is limited

to failures resulting from defective components and

LCD-Panel 19 inch diagonal size (48.3 cm visible), low radiation according to

TCO'03, certified to ISO 13406-2, pixel fault class II

Panel-Technology TN

Viewing angle (Contrast ratio CR 10:01) horizontal 150°, vertical 135° (typical)

(Contrast ratio CR 05:01) horizontal 180°, vertical 155° (typical)

Contrast ratio typical 700:1, max. 800:1

Reaction time 8 ms (typical)

Brightness typical 300 cd/m2, max. 320cd/m2

Input signal video analogous: 15-Pin Mini-D-SUB, digital: 24 pin DVI

Display colours 16.2 mill. colours

Synchronisation 30-83 kHz horizontal, 50-75 Hz vertical

Video band width 135 MHz pixel rate

Ergonomic resolution 1280 × 1024 (60 Hz)

Audio

Amplifier 1 W at 8 Ohm loudspeaker

Peak audio 2 W

Power supply 100-240 V AC, 50-60 Hz

Power consumption

ON-Status max. 37 W

Power saving function TCO 03, EPA Power Management

Colour of the status indicator: :

green ON Status max. 37 W

orange power saving

according to EPA <

1 W

Dimensions/weight: width 407 mm, height 468 mm, depth 145mm, 5,5 kg (net)

Environment conditions:

Operation 0 to+40 °C, r. h. 20%-80% (non-condensing)

Storage -20 to +60 °C, r. h. 8%-95% (non-condensing)

Indice

Altri manuali BELINEA Monitor

BELINEA

BELINEA 101910 Manuale utente

BELINEA

BELINEA 101927 Manuale utente

BELINEA

BELINEA 101902 Manuale utente

BELINEA

BELINEA 10 55 70 Manuale utente

BELINEA

BELINEA 10 60 75 Manuale utente

BELINEA

BELINEA 101555 Manuale utente

BELINEA

BELINEA 10 Manuale utente

BELINEA

BELINEA 1705 S1 Manuale utente

BELINEA

BELINEA 101915 Manuale utente

BELINEA

BELINEA 15 Manuale utente

BELINEA

BELINEA 2485 S1W Manuale utente

BELINEA

BELINEA 10 60 65 Manuale utente

BELINEA

BELINEA 101911 Manuale utente

BELINEA

BELINEA 10 18 30 Manuale utente

BELINEA

BELINEA 2025 S1 Manuale utente

BELINEA

BELINEA 10 Manuale utente

BELINEA

BELINEA 103026 Manuale utente

BELINEA

BELINEA 101910 Manuale utente

BELINEA

BELINEA 10 Manuale utente

BELINEA

BELINEA 10 17 28 Manuale utente

BELINEA

BELINEA 10 80 35 Manuale utente

BELINEA

BELINEA 10 30 50 Manuale utente

BELINEA

BELINEA CRT-Monitor Manuale utente

BELINEA

BELINEA 10 80 80 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione