Bell System BellProx PR50X Manuale utente
BellProx
Model PR50X
Proximity / Keypad reader kit
Kit contents
1 bPX10 Proximity / Keypad reader, Surface fitting
1 340C Power supp y, 13.8V DC, 1.5A
1 203 Lock re ease, surface fitting, fai secure
1 5080 Exit button, surface fitting
1 Pack of 50 Fobs
1 Security too for bPX10
1 MOV Lock protection device
2 Rubber fixing p ugs
2 Se f tapping fixing screws
www.bellsystem.co.uk
Programming the BellProx Reader
For Security, please change the Master Code before the Reader is put into use.
Function
Keypad/Reader
Notes
Master Code
:
(Required for adding and deleting
Fobs
and other system programming)
Enter rogram
Mode
* <MASTER CODE>#
MASTER CODE
is a 6-8 Digit Code:
(Factory default is 999999)
Change Master
Code
0 <New Code> # <New Code> #
New Code
is any 6-8 Digit number
Exit rogram
Mode
*
rogram M
ode will also timeout after 30
seconds of inactivity
lease choose the required mode before adding User Fobs or INs: (Must be performed in rogram Mode)
Working Mode:
Fob
only
3
0 #
Only Fobs can be used (no INs)
Fob
and IN
3 1 #
Fob
must always be used together with a IN
Fob
or IN
(Default )
3 2 #
Either a
Fob
or IN can be
assigned to each
User ID
Must be performed in rogram Mode – see Master Code above
Add/Delete Fobs
Add a
Fob
1 <User ID> # FOB #
User
ID
a unique number from 1 to 1000
which should be assigned to each Fob
FOB
Hold the Fob to the reader
Add a IN to
the
Fob
(Mode 31)
Add a
Fob
first as above
then
Exit rogram Mode.
IN can be added to
Fob
in User Mode
(See User Instructions below)
Add a IN only
(Mode 32)
1 <User ID> # PIN # *
User ID
a unique number from 1 to 1000
which should be assigned to each Fob
PIN
Any 4-digit number (except 1234)
Delete a
Fob
using the Fob
2 FOB #
In Mode 31 the associated IN is deleted too.
Delete a
Fob
/ IN
using the User ID
2 <User ID> # *
Delete all
Fobs
/ INs
2 0 0 0 0 #
Use wit caution!
Misc
Factory Reset
ower Down
the R
eader:
Hold down the # key:
ower Up:
Release the # key after two beeps
Does not delete
Fobs
or PINs
Master Code is reset to 999999
User Instructions (If required, ress
*
to exit programming mode)
Open Door with Fob
FOB
( resent Fob to reader)
Open Door with IN
<PIN> #
(eg 4052#)
Open Door with
Fob
and IN
FOB <PIN> #
Add IN to
Fob
User
(Mode 31 only)
* FOB 1234 # <PIN> # <PIN> #
Change IN with
Fob
(Mode 31 only)
* FOB <O d PIN> # <New PIN> # <New PIN>
Change IN with User ID
(mode 31 & 32)
* <User ID> # <O d PIN> # <New PIN> # <New PIN> #
Must be performed in rogram Mode – see Master Code above
Door Settings
Change Lock Time
4 <Lock Time> # *
Lock Time
is 0-99 ( seconds)
Alarm Duration
5 <A arm Time> #
A arm Time
is 0, 1, 2, or 3 (minutes)
Enable Door open
detect
6 1 #
Requires
Door monitor switch
Disable Door open
detect
6 0 #
Ke
y
pad Lockout & Alarm Options
(10 Invalid
Fob
s or Pins wit in 10 mins)
Normal
7 0 #
No Alarm or lockout
Lockout
7 1 #
Keypad is locked out for 10 mins
Alarm operate
7 2 #
Alarm and ext. buzzer sound for 10 mins
LED Indication
Red, flashing
Idle
Red, solid
In rogram mode
Green, brief flash
Sequence acknowledged
Green, solid
Door unlocked
Typical wiring diagram
bPX10 Reader Specification
Operating voltage
9
-
28V DC
Users
1000
Current consumption
40mA Idle, 60mA Active
Dimensions (mm)
58 (W) x 120 (H) x 22 (D)
Lock output
1A max.
Water resistance
I 68
Door Bell button
ush to make, 20mA
max.
Finish
Strong Zinc Alloy
Electroplated anti-vandal
Keys
Illuminated
Bell rox Rev 3
Indice
Altri manuali Bell System Tastiera
