Bellman & Symfon BE1411 Istruzioni per il montaggio

BE1411

Buttons and connections

Visit door transmitter

Test / program buttons

Ext. trig. input

3.5 mm ext. mic. input BE9199 / BE9200

External microphone

Internal microphoneLED lights

Doorbell push button

In the box

BE1411 Visit door transmitter

2

¯1.5 V AA (LR6)

lithium or alkaline batteries

Velcro for wall mounting

Screw and wall plug

Power and battery

Battery power

2¯1.5 V AA lithium or alkaline

type batteries

Power consumption

Active < 70 mA

Idle position < 15 μA

Operation time

Alkaline batteries ~ 5 years

Lithium batteries ~ 10 years

Environment

For indoor use only

Operating temperature

0° to 35° C, 59° to 95° F

Relative humidity

15% to 90%, non-condensing

Frequency and coverage

Frequency: 314.91 MHz, 433.92 MHz

or 868.30 MHz, depending on region

Coverage: 50 - 250 m, 55 - 273 yd.

depending on the radio frequency

and the building’s characteristics

Accessories

The following accessories are available:

BE9199 External microphone 2.5 m

BE9200 External microphone 0.75 m

Dimensions and weight

Height: 100 mm, 4.0"

Width: 65 mm, 2.6"

Depth: 27 mm, 1.1"

Weight: 120 g, 4.2 oz. incl. batteries

Activation

The test buttons and the int. mic.

The electromagnetic detector

The external microphone accessory

The existing doorbell connected to

the external trigger input

Inputs

3.5 mm external microphone input

External trigger input

Technical specications

Installation – single sound source

Using the transmitter’s internal microphone

1Pull the battery tab to start the transmitter.

Clean the wall with the wet wipe and remove the protective lm from the Velcro.

2Mount the door transmitter to the left of the doorbell’s sound source, as close as possible.

You can also use the supplied screw and plug.

1 2

Max 3 cm, 1.2"

Sound source

Alternative installation – single sound source

Using the external microphone accessory

1Connect the external microphone (sold separately) to the transmitter.

Remove the protective lm and attach it to the intercom’s speaker.

2Pull the battery tab to start the transmitter. Remove the protective lm from the Velcro and mount the transmitter on the wall.

3Within 2 min, press the lower button 10 times to turn o the internal microphone. The LEDs will blink 3 times in red to conrm.

Note: If you exceed 2 minutes, you need to restart the transmitter by removing the batteries and putting them back in again.

Turning the internal microphone back on

Restart the transmitter by removing the batteries and putting them back in. Within 2 minutes, press the lower button

10 times to turn the internal microphone back on. The LEDs will blink 3 times in green to conrm.

Ext. mic.

(sold separately)

1 2 3

°10

Visit door transmitter

Installation – intercom and electronic doorbell

1Remove the protective lm from the external microphone (sold separately) and attach it to the intercom’s speaker.

Connect it to the door transmitter.

2Pull the battery tab to start the transmitter.

Clean the wall with the wet wipe and remove the protective lm from the Velcro.

3Mount the door transmitter to the left of the doorbell’s sound source, as close as possible.

Note: The intercom and doorbell must be at least 25 cm, 10" apart to avoid sound interference.

Installation – intercom and mechanical doorbell

If you have an intercom and a mechanical doorbell, you may need two door transmitters, i.e. one for each sound source.

1Pull the battery tab to start each door transmitter.

Clean the wall surfaces with the wet wipe and remove the protective lms from the Velcros.

2Mount one of the door transmitters to the left of the doorbell and the other to the left of the intercom’s speaker, as close

to the sound sources as possible.

Ext. mic.

(sold separately)

Electronic

doorbell

Max 3 cm, 1.2"

Max 3 cm, 1.2" Max 3 cm, 1.2"

1 2

Using electromagnetic detection

The door transmitter can be set to detect electromagnetic elds emitted by electromechanical doorbells.

Here is how it’s done:

Activating electromagnetic detection: Move the 4th signal-switch to the up (on position).

Deactivating electromagnetic detection: Move the 4th signal-switch to the down (o position).

Ext. trig

Installation – hardwiring your doorbell

1Pull the battery tab to start the transmitter.

Within 2 min, press the lower button 10 times to turn o the internal microphone. The LEDs will blink 3 times to conrm.

2Remove the front cover to access the screw terminal. There are 3 connection points:

Use 1 and 2to connect an active switch, like a relay with current (2–30VDC, polarity independent

or 2–24VAC, 5 - 150Hz).

Use 2and 3to connect a passive switch, like a push button.

3Put the front cover back, remove the protective lm from the Velcro and mount the door transmitter on the wall.

123

°10

2 31

Visit door transmitter

Using the doorbell or intercom

1 Press the button on the doorbell or intercom.

The LED on the transmitter lights up in green to show

that the sound is detected.

2 The green Visit LED on the receiver lights up to show

that the radio signal was received. In addition, it starts to

sound, ash or vibrate depending on the receiver.

Note: If you have changed the signal pattern, it will react

in accordance with the table on the following spread.

Testing the connection

Using the test button

1 Press both test buttons simultaneously on the door

transmitter. The top LED lights up in green to show that

a radio signal is being transmitted.

2 The green Visit LED on the receiver lights up to show

that the signal was received. In addition, it starts to

sound, ash or vibrate depending on the receiver.

Note: If you have changed the signal pattern, it will react

in accordance with the table on the following spread.

1 2 1 2

1 2 3

Try again

Optimizing the doorbell detection

The next step is to teach the transmitter to recognize your doorbell.

1Press and hold button 1 until the top LED start to blink. Release it to start the recording.

2For door buzzers (with continous sound): Press and hold the doorbell for at least 8 seconds.

For door chimes (with a "ding-dong" sound): Press the doorbell at least 8 times.

3Press button 1 on the transmitter to stop the recording. If the LED lights up in red, you need to repeat steps 1 and 2.

If you have an intercom, use button 2 and follow the steps above to record its sound.

Note: To delete all recorded sounds, press and hold button 1 and 2 simultaneously for 5 s. All radio key settings and

signal settings are kept intact.

Default signal pattern

When the door transmitter is activated, the following happens:

1The LED on the transmitter lights up in green to show that it’s signalling the receiver.

2The Visit LED on the receiver lights up in green and it starts to sound, ash or vibrate with a certain pace, called signal

pattern. The transmitter and the connected accessories determine the signal pattern. The default is as follows:

Transmitter Receiver signal pattern

Source LED LED Sound Vibration Flash

Internal microphone Green, top Green light 1¯door chime, low Slow Yes

External microphone Green, bottom Green blinks 2¯door chime, high Slow Yes

Connected doorbell Green, top 3¯green blinks 1¯door chime, high Slow Yes

Changing the signal pattern

The transmitter controls the signal pattern. Open the transmitter front cover and move the

signal switches according to the table below to change it:

Transmitter Receiver signal pattern

Switch Source LED Sound Vibration Flash

Int. mic. / learned signal 1 / test Green light 1¯door chime, low Slow Yes

Ext. mic. / learned signal 2 Green blink 2¯door chime, high Slow Yes

Connected doorbell 3¯green blinks 1¯door chime, high Slow Yes

Int. mic. / learned signal 1 / test 2¯green blinks 2¯door chime low Slow Yes

Ext. mic. / learned signal 2 3¯green blinks 1¯door chime, high Slow Yes

Connected doorbell Green blinks 2¯door chime, high Slow Yes

Int. mic. / learned signal 1 / test 3¯green blinks 1¯door chime, high Slow Yes

Ext. mic. / learned signal 2 2¯green blinks 2¯door chime, low Slow Yes

Connected doorbell 3¯orange blinks Baby melody Fast Yes

Int. mic. / learned signal 1 / test Green blinks 2¯door chime, high Slow Yes

Ext. mic. / learned signal 2 Green light 1¯door chime, low Slow Yes

Connected doorbell Orange blinks Baby melody Fast Yes

Int. mic. / learned signal 1 / test Green light 1¯door chime, low Slow Yes

Ext. mic. / learned signal 2 3¯green blinks 1¯door chime, high Slow Yes

Connected doorbell 2¯green blinks 2¯door chime, low Slow Yes

Int. mic. / learned signal 1 / test Green light 1¯door chime low Slow Yes

Ext. mic. / learned signal 2 Green blinks 2¯door chime, high Slow Yes

Connected doorbell Yellow blinks 2¯ring signal, high Medium Yes

Int. mic. / learned signal 1 / test 3¯green blinks 1¯door chime, high Slow Yes

Ext. mic. / learned signal 2 Green light 1¯door chime, low Slow Yes

Connected doorbell Red + orange light Emergency siren Long Yes

Int. mic. / learned signal 1 / test Green blinks 2¯door chime, high Slow Yes

Ext. mic. / learned signal 2 2¯green blinks 2¯door chime, low Slow Yes

Connected doorbell Red blinks Fire horn Long Yes

O

Visit door transmitter

If Try this

The LEDs blink in orange every minute Replace the batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries.

The transmitter LEDs blink in orange

every second

There are other competing sound sources around the door transmitter. Switch

them o or turn them down.

Disconnect the external microphone accessory to make sure it is not faulty.

The transmitter LED lights up when I

press the doorbell or intercom – but

the receiver is not activated

Check the the transmitter batteries and the receiver batteries and connections.

Move the receiver closer to the transmitter to make sure it’s within radio range.

Check that the door transmitter and the receiver are set to the same radio key.

For more information, see Changing the radio key.

The transmitter LED doesn’t light up

when I ring the doorbell or intercom

Ring the doorbell while moving the transmitter closer and further away from

the sound source. The ideal distance is less than 3 cm.

Program the transmitter to recognize the doorbell sound. See Programming.

If the signal varies a lot in strength or tone, change to electromagnetic detection.

If the door transmitter is still not activated, press and hold button 1 and 2

simultaneously for 5 s to clear the recorded sounds and repeat the steps above.

The receiver is activated for no

apparent reason

There is probably another Visit system installed nearby that triggers your

system. Change the radio key on all units, see Changing the radio key.

Changing the radio key

If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio

interference, you need to change the radio key on all units. The radio key switches are located under the transmitter cover.

Here is how you change the radio key:

1Open the transmitter front cover and move any radio key switch to the up (on position) to

change the radio key. By default, all radio key switches are positioned down (o).

2Press and hold the test/function button on the receiver until the green and yellow Visit LEDs

blink alternately. Release the button.

3Press both test buttons simultaneously on the transmitter within 30 s to send the new radio key.

4All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.

Note: All Visit units must be set to the same radio key in order to operate as a group.

°5

Troubleshooting

1 2 3 4

O

Visit door transmitter

Altri manuali per BE1411

Indice

Altri manuali Bellman & Symfon Sistema di interfono

Bellman & Symfon

Bellman & Symfon BE1411 Manuale utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente