BENDIX SmarTire Manuale utente

Full Function Display

User’s Manual

SmarTire Systems Inc. reserves the right to change the contents of this manual at any time

and without notice. The information contained in this manual is proprietary and must not be

reproduced without prior consent from SmarTire Systems Inc.

TABLE OF CONTENTS

Notices 3

FCC Notice 3

European Regulations 4

System Scope of Use and Warnings 5

The SmarTire®System and Tire Maintenance 5

System Installation and Usage 5

Warnings 5

Introduction 6

Full Function Display Features 6

Power Stages 7

Full Function Display Controls and Indicators 7

Operation 8

Getting Started 8

Checking Tire Conditions 9

Alerts and Warnings 10

Pressure Deviation Alert 10

Low Pressure Warning 11

High Temperature Alert 11

Programming 12

To Enter Programming Mode 12

Display Icons 12

Operating Settings –Level 1 13

Cold Inflation Pressure 13

Low-Pressure Warning 14

SMARTIRE SYSTEMS INC.

Pressure Deviation Alert 15

Understanding Temperature Compensated Pressure Readings 16

High Temperature Alert 17

Metric or Imperial Measurement Selection 18

Tire Rotation 19

Advanced Programming –Level 2 21

Slope 21

Learn 22

Receiver Programming Mode –Level 3 25

Low Pressure Alert 25

Installation and Service 26

Installation 26

Full Function Display Specifications 27

Service and Warranty 28

System Diagnostics 28

Troubleshooting 28

Replacing a Full Function Display 29

Part numbers 29

US Warranty 29

Canadian Warranty 31

European Warranty 32

Notices

FCC NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions : (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this device without the express approval of SmarTire

Systems Inc. may void the userís authority to use this device.

SMARTIRE SYSTEMS INC.

EUROPEAN REGULATIONS

This device complies with all European Electromagnetic compatibility regulations

(95/54 /EC and EN300 220-1). The equipment has been tested and found to comply

with the above regulations, and in addition it meets the requirements for low

powered transmitters/receivers as defined by the relevant radio approval authority.

The regulations are designed to provide reasonable protection against harmful

interference or susceptibility. Changes made to this device without the express

approval of SmarTire Europe Ltd. may void the user’s authority to use this device.

SYSTEM SCOPE OF USE AND WARNINGS

The SmarTire

System and Tire Maintenance

This system is a sensing device designed to identify and display tire operating data

and activate an alert or warning when pressure or temperature irregularities are

detected. It is the responsibility of the driver to react promptly and with discretion

to alerts and warnings. Abnormal tire inflation pressures should be corrected at

the earliest opportunity.

System Installation and Usage

Use of the SmarTire

system requires that it has been properly installed and

programmed by qualified personnel according to SmarTire Systems Inc. documentation.

This includes the Owner s Manual and any supplementary installation instructions

included with system components.

Warnings

1. When an alert or warning conditions is detected, reduce vehicle speed to an

appropriate safe level and proceed to a safe stopping location or facility where

the tire can be inspected and serviced.

2. The pressure deviation alert indicates that the pressure has dropped a selected

amount below the required pressure for that level of tire temperature.

3. The low pressure warning indicates that the air pressure has dropped to a

selected minimum.

4. The high temperature warning indicates that the contained air temperature has

exceeded the selected maximum. A tire temperature buildup can be caused by a

number of factors including severe under inflation, hard sustained braking,

vehicle overload and sustained high speeds.

Introduction

FULL FUNCTION DISPLAY FEATURES

The Full Function Display adds additional features to a previously installed SmarTire

system (refer to the Tire Pressure Monitoring System Owner’s Manual ). It provides

digital tire pressure and temperature data for up to 20 tire positions as well as

enabling warning level adjustment to suit driver needs.

The system’s modular design offers two digital display units. One clips onto the basic

receiver, while the other can be remotely located with an interconnecting cable.

SMARTIRE SYSTEMS INC.

ULL

UNCTION

ISPLAY

ULL

UNCTION

EMOTE

ISPLAY

POWER STAGES

The Full Function Display has an energy saving feature that turns lights on to full

intensity (Active stage) only when required to display alert conditions or program

the unit. The unit automatically switches to lower power stages when no control

activity is detected.

Full Function Display Controls and Indicators

Low pressure warning

Alarm light

TIRE button

MODE button

Alert indicator

Learn mode

Set button

Towing vehicle indicator

Units of pressure or

temperature

Tire rotation program

Cold pressure program

Programming mode

Numerical display

Programmed wheel position

No data

Data received

SMARTIRE SYSTEMS INC.

Operation

GETTING STARTED

Mount the display unit and connect to power source.

When power is applied to the receiver, the Full

Function Display momentarily turns on all icons,

beeps, and the alarm light blinks once. The unit

then goes into stand-by mode waiting for data

from the wheel transmitters.

Until the vehicle is in motion no data will be

received from any installed transmitter. The

display will remain blank as shown.

The respective tire icon is filled in as soon as data

from its transmitter is received. The windshield/

louver is shown for any towing vehicle transmitter.

After data from all transmitters is received the

display will be in the state shown at left until an

alert or warning condition is detected.

(Normal Mode)

Data from a towed vehicle is indicated by tire

icons with no windshield/louver icon.

Note: The system will alternate views between

the towing and towed vehicle when operating

with this configuration.

Altri manuali per SmarTire

Indice

Altri manuali BENDIX Accessori per automobili

BENDIX

BENDIX VORAD VS-400 Manuale utente

BENDIX

BENDIX Intellipark Manuale utente

BENDIX

BENDIX Bendix Wingman Advanced Manuale utente

BENDIX

BENDIX ADB22X-V Istruzioni per il montaggio

BENDIX

BENDIX Wingman FLR20 Manuale utente

BENDIX

BENDIX VORAD VS-400 Manuale di installazione e funzionamento

BENDIX

BENDIX Sheppard Istruzioni per il montaggio

BENDIX

BENDIX TC-2 Manuale utente

BENDIX

BENDIX ACTIVE STEERING SYSTEM Manuale utente

BENDIX

BENDIX VORAD VS-500 Manuale utente

BENDIX

BENDIX TLV-9000 Istruzioni per il montaggio

BENDIX

BENDIX TABS-6 TRAILER ABS MODULE Istruzioni per il montaggio

BENDIX

BENDIX AUTOVUE FLC-20 Istruzioni per il montaggio

BENDIX

BENDIX SmarTire Manuale utente

BENDIX

BENDIX BlindSpotter BW2860 Guida alla configurazione

BENDIX

BENDIX Gen. 4 ABS ECU Manuale utente

BENDIX

BENDIX Bendix Wingman ACB Istruzioni per il montaggio

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Aries

Aries 203015 Manuale utente

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente