Benison V5 Manuale utente

BENISON

VHF FM TRANSCEIVERS

INSTRUCTION MANUAL

FOREWORD

Thank you for purchasing the BENISON-V5 FM transceiver. This

transceiver is designed for those who require quality, performance and

outstanding reliability under the most demanding conditions.

FEATURES

5 W of ample output power

VOX standard

CTCSS and DTMF encoder/decoder standard

LCD/KEYBOAD backlight

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely before using the

transceiver.

SAVE THIS INSTRUCTION MANUAL- This instruction manual contains

important operating instructions for the transceiver.

PRECAUTIONS

WARNING! NEVER hold the transceiver so that the antenna is very close to, or

touching exposed parts of the body, especially the face or eyes, while transmitting.

The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches)

away from the lips and the transceiver is vertical.

WARNING! NEVER operate the transceiver with a headset or other audio accessories

at high volume levels. Hearing experts advise against continuous high volume

operation. If you experience a ringing in your ears, reduce the volume or

discontinue use.

NEVER connect the transceiver to a power source that is DC fused at more than 5 A.

Accidental reverse connection will be protected by this fuse, but higher fuse values

will not give any protection against such accidents and the transceiver will be

ruined.

NEVER attempt to charge alkaline or dry cell batteries. Be aware that external DC

power connections will charge batteries inside the battery case. This will damage

not only the battery case but also the transceiver.

DO NOT push the PTT when not actually desiring to transmit. Place the unit in a

secure place to avoid inadvertent use by children.

DO NOT operate the transceiver near unshielded electrical blasting caps or in an

explosive atmosphere.

AVOID using or placing the transceiver in direct sunlight or in areas with

temperatures below –10°C (+14°F) or above +60°C(+140°F).The use of non-becom

battery packs/chargers may impair transceiver performance and invalidate the

warranty.

Even when the transceiver power is OFF, a slight current still flows in the circuits.

Remove the battery pack or case from the transceiver when not using it for a long

time. Otherwise, the battery pack or installed Ni-Hi batteries will become exhausted.

SPECIFICATIONS

GENERAL

. Frequency coverage : 245.0000 -245.9875 MHz

. Type of emission : 8K50F3E

. Number of channels : 80 ch + 10 ch

. Power supply requirement : 7.2 V DC (negative ground; supplied battery pack)

. Current drain (approx.) : Transmit at High (5.0 W) 1.7 A, at Low (1.0 W) 700 mA

: Receive rated audio 250 mA

: stand-by 50 mA

. Frequency stability : ±0.001 %

. Usable temperature range :-10°C～+60°C

. Dimensions (projections not included) : 54(W)×132(H)×35(D) mm

. Weight (with ant., BP-512) : 370 g ; 13.1 oz.

TRANSMITTER

. RF output power (at 7.2 V DC) : 5 W / 1 W (High / Low)

(with supplied battery pack)

. Modulation system : Variable reactance frequency modulation

. Maximum frequency deviation : ±2.5 kHz

. Spurious emissions : 70 dB typical

. Adjacent channel power : 60 dB typical

. Transmitter audio distortion : Less than 3% at 1 kHz, 40% deviation

RECEIVER

. Receive system : Double conversion superheterodyne system

. Intermediate frequencies : 1st 21.700 MHz / 2nd 450 kHz

. Sensitivity : 0.18 μV at 12 dB SINAD (typical)

. Squelch sensitivity : 0.25 μV at threshold (typical)

. Adjacent channel selectivity : 65 dB (typical)

. Spurious response rejection : 70 dB (typical)

. Intermodulation rejection ratio : 70 dB (typical)

. Hum and noise : 40 dB (typical)

. Audio output power (at 7.2 V DC) : 500 mW typical at 5% distortion with an 8 load

All stated specifications are subject to change without notice or obligation.

SUPPLIED ACCESSORIES

Accessories included with the transceiver:

1: Antenna…………………………………………………… 1

2: Belt clip …………………………………………………… 1

3: OPT sheet …………………………..…………………… 1

4: AC Adapter ….…………………………………………… 1

5: Battery pack………………… …………………………… 1

6: Battery charging stand.. ………………………………… 1

QUICK REFERENCE

Preparation

Battery pack replacement

Slide the battery release forward, then pull the battery pack upward with the

transceiver facing away from you.

QUICK REFERENCE

Antenna

Attach the antenna to the transceiver as lustrated at right.

Belt clip

Attach the belt clip to the transceiver as illustrated below.

PANEL DESCRIPTION

Switches, controls, keys and Connectors

1: POWER SWITCH [POWER]/CONTROL DIAL [VOL]

Rotate to adjust the volume level, to turn the power ON and OFF.

2:CTCSS SWITCH

Push and hold to force the CTCSS open and set the transceiver

3:PTT SWITCH [PTT]

Push and hold to transmit; release to receive.

4:SQUELCH SWITCH [SQL]

Push and hold to force the squelch open and set the transceiver

to the squelch level adjustable condition.

5:UP/DOWN KEYS

Selects the operating frequency.[UP]/[DN]

6:KEY PAD

Used to enter operating frequency, the DTMF codes, etc.

7:ANTENNA CONNECTOR

Connects the supplied antenna.

8:[SP]/[MIC] JACK

Connect an optional speaker-microphone or headset, if desired.

The internal microphone and speaker will not function when either is connected.

9:FUNCTION DISPLAY

*The assigned function for [SQL] and [DP]/[DN] can be traded in INITIAL SET MODE.

BASIC OPERATION

Power ON

POWER SWITCH

Rotate to adjust the volume level, to turn the power ON and OFF.

Setting a frequency

UP/DOWN KEYS

Selects the operating frequency. [UP] / [DN]

Push [D•CLR] to select frequency mode

Push [C•MR] to select channel mode

Setting audio/squelch level

To set the audio level

Rotate [VOL] to set the desired audio level while receiving a signal.

To set the squelch level

While pushing [SQL], push [UP]/[DN] to set the squelch level.

•The squelch level “0” is loose squelch,“25” is tight squelch.

Receive and transmit

Adjust audio volume to the desired level.

Set a frequency.

When a signal is received:

• Squelch opens and audio is emitted from the speaker.

• Signal indicator shows the relative signal strength level.

Push [A•FUNC], then push [9•H/L] to toggle output power between high and low.

• “L” appears when low output power is selected.

Push and hold [PTT] to transmit, then speak into the microphone.

• “TX” appears.

•Do not hold the microphone too close to your mouth or speak too loudly. This may

Altri manuali per V5

Indice

Altri manuali Benison Ricetrasmettitore

Benison

Benison BE-245A Manuale utente

Benison

Benison V7 Manuale utente

Benison

Benison JB-9 Manuale utente

Benison

Benison JB-4 Manuale utente

Benison

Benison A86 Manuale utente

Benison

Benison V7 Manuale utente

Benison

Benison V5 Manuale utente

Benison

Benison V9-S Manuale utente

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente