BenQ GW2381 Manuale utente
Recycle Disassemble Instruction
(Dismantled Information)
Requirements according to ANNEX VII of DIRECTIVE 2012/19/EU
on waste electrical and electronic equipment (WEEE)
Materials and components with hazardous content
LCDs may contain hazardous substances like Pb and BFRs which are covered by
exemptions under the RoHS directive. However, the majority is present in the printed
circuit boards assembly. In order to reduce emissions as much as possible, a complete
disposal of the old appliance is required. This treatment may only be performed in
authorized handling plants.
Product Name: LCD Monitor
Model No.: GW2381,GW2381E
Disassembly Tools
Tool
picture
Philips Screwdriver for M3 Screw
Nosed Pliers
Diagonal Cutting Pliers
Slotted screwdriver
Six Point Sockets
Philips Screwdriver for M2.5 Screw
Knife
1.
Product exploded view
2.
Package view
External cable
Item
Description
Qty
Unit
P01
Power cable
1
PCS
P02
D-Sub cable
1
PCS
P03
DVI cable
1
PCS
P04
IP cable
1
PCS
P05
Audio cable
1
PCS
Disassembly process
1)
Remove the base
1.1.
Place the monitor face down on a smooth surface, use your fingers to release the screw located at the bottom of the
base.
6
Place the monitor face down on a smooth surface, use your fingers to release the screw located at the bottom of the
base.
2)
Remove the stand assembly with both hands.
While using the sharp object to insert into the release hole, slide the base out.
3)
Remove the rear cover
3.1
Use the screwdriver (not provided) to release the screws first.
3.2
Use the tool (as below picture) to open all the latches slowly and carefully from one of opening hole designed on
the bottom sides of back cover.
5)
Remove
the
boards
from
the
main
frame
7
4)
Remove the main frame from the panel.
4.1
Remove all the tapes.
4.2
Release the screws located on the top of main frame and disconnect all the cables to remove the main frame.
6)
Remove
the
middle
frame
and
bezel
from
panel
8
5.1
Turn over the main frame and remove the mylar from board first.
5.2
Release all the screws from the boards and main frame.
5.3
Disconnect all the cables to separate the boards from each other.
6.1
Release all the screws first.
6.2
Carefully pull down the bezel. Now, the panel is totally separated from middle frame.
7) Disassemble the sensor board and key board from middle frame.
1.1 Remove the sensor board
1.1.1 Take out the cover first, then release the screw on the top of board.
7.2 Remove the key board, press the key button to take the board out of middle frame.
9
10
Assembly:
1) Prepare main board, power board and some essential cables. Connect the cables between boards as below
picture showed.
2) Put the boards to main frame in the place by tightening the screws to fasten it.
3) Return Mylar back to the power board.
11
4) Tighten the screws on the side of main frame
5) Assemble the sensor board to the bottom center of middle frame as above reverse steps.
6) Assemble the key board to the middle frame as above reverse steps.
7) Assemble the middle frame and main frame to the panel.
7.1
Locate the assembled middle frame in the place, install the bezel and tighten all the screws.
7.2
Put the speakers in the place.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BenQ Monitor
BenQ
BenQ G2400WAD Manuale utente
BenQ
BenQ GL2440HM Manuale utente
BenQ
BenQ XL2420T Manuale utente
BenQ
BenQ RL2240H Manuale utente
BenQ
BenQ FP547 - 15" LCD Monitor Manuale utente
BenQ
BenQ FP567S Manuale utente
BenQ
BenQ FP72V Manuale utente
BenQ
BenQ FP991 - 19" LCD Monitor Manuale utente
BenQ
BenQ RL Series Manuale utente
BenQ
BenQ RL2450HT Manuale utente
BenQ
BenQ BL2420PT Manuale utente
BenQ
BenQ FP72E S Guida utente
BenQ
BenQ FP95G Manuale utente
BenQ
BenQ DesignVue PD Series Manuale utente
BenQ
BenQ M2400HD - 24" LCD Monitor Manuale utente
BenQ
BenQ FP767 - 17" LCD Monitor Manuale utente
BenQ
BenQ G Series Manuale utente
BenQ
BenQ BL2785TC Manuale utente
BenQ
BenQ FP94G Manuale utente
BenQ
BenQ VW2430H Manuale utente
