BeSense X32_ZWAVE Manuale utente

ix32

Zwave PLUS Ceiling PIR Sensor

I. Introduction

X32_ZWAVE wireless PIR sensor adopts latest detection & induction technologies

including Energy Accumulation Management, Dynamic Random Time Division

Technology etc. And it combines multi-zones comprehensive induction calculation and

uses advanced MCU digital processing technology. Besides, it has the advantages of

stable & reliable detection, low false alarm and pet immune.

•Special Fresnel lens with patented technology, built-in far infrared wave with above

95% transmittance rate

•Adopt original imported Heimann sensor from Germany, with high sensitivity & low

false alarm

•Real anti-visible light technology, no false alarm under 6500LUX strong light

interference With sealed induction cavity design, prevent false alarm caused by

thermal current interference

•Configurable detection sensitivity, suitable for variety of detection environments With

fuzzy logic algorithm & fuzzy recognition technology, pet-immune Ultra-low power

consumption, 2 years of battery working life

[email protected]



Detection Area

[email protected]



II. Network Inclusion/ Exclusion

The sensor must be added to the Zwave network prior to use. To include the sensor in a

network both the sensor and the Network controller or HUB must be in inclusion mode

at the same time.

Add : start by placing the controller in inclusion mode. Activate the inclusion mode at

the sensor pressing the tamper switch 3 times, then the door sensor will stay in

enrollment state.

Wait about 15-30 seconds while the sensor and controller finished the inclusion

process.

Remove: enter the Exclusion Mode on the controller, and press the tamper switch 3

times, then the door sensor will be removed after 15-30 seconds.

III. Restore Factory Settings

Press the tamper switch for 6 times to restore factory settings.

[email protected]



IX 32 has the following 3 types of pulse optional and 3 operates mode:!

Pulse 1: The detector gives an alarm when it checks one pulse.

Pulse 2: The detector gives an alarm when it checks two pulses.

Pulse 3: The detector gives an alarm when it checks three pulses.

The pulse count is higher and the sensitivity is lower, but can reduce false alarm.

Test Mode (High Battery consumption) : Alarm will be triggered each 5s.

Power-save Mode (Recommended): Alarm will be triggered again with above 3min

interval from its first alarm. After triggered, it will send alarm elimination signal to the

relevant device in at least 3 minutes.

Code Mode: without any function

[email protected]



[email protected]



Here are some instructions that should help you

get our Motion Sensor device handler to work

in SmartThings.

Why update the handler?

•Customized to avoid false alarms

•Generate Tamper alerts

•Battery indicator

•Colors and Background improved

How to ADD a device Handler for the BeSense

Motion Sensor?

1. Log in here with the same username and password you use for your SmartThings

app: https://graph.api.smartthings.com/login/auth

[email protected]



2. Click on My Device Handlers in the top menu

3. In the top right corner, click on Create new device handler and choose From code

from the top tab menu. You'll be presented with a blank area where you can copy the

code from this link and paste it in (it's always best to use the raw version of the code)

https://besense-iot/smartthings/besense_handler.txt

[email protected]



4. Next, scroll to the bottom and click Create. Now click Save, then click Publish > for

me.

[email protected]



You should now see this device type in your list of Device Handlers

How To assign a custom DEVICE HANDLER to my zwave device

Simply exclude the device if you had included it prior to installing the new device

handler. Then add the device to your SmartThings hub by clicking on Add thing > +

Connect New Device in your app. Press and release the tamper switch three times on

the sensor quickly.

Remember to keep the device within 3 feet away from your hub during inclusion — the

device should be automatically discovered as the BeSense Motion sensor. Then, leave

the sensor by the hub for a few hours so it can fully configure.

And that should be it! I hope this was helpful in simplifying the process behind custom

device handlers. Feel free to contact us if you have any question.

[email protected]



BeSense Z-Wave

Command Class Specification

When the door sensor is opened or recovered, it will send “Binary Sensor Report” and

“Notiﬁcation Report” commands to the device under Lifeline group.!

When door sensor is opened:!

Sensor Binary Report, Value = 0xFF, Type = 0x0C

Notiﬁcation Report, Notiﬁcation Type = 0x07, Event = 0x08 When door sensor is recovered:

Sensor Binary Report, Value = 0x00,Type = 0x0C Notiﬁcation Report, Notiﬁcation Type = 0x06,

Event = 0x16

When tamper switch is triggered or recovered, the door sensor will send “Sensor Binary Report”

and “Notiﬁcation Report” command to the device under Lifelinegroup.!

Tamper Triggered:!

Sensor Binary Report, Value = 0xFF,Type = 0x08

Notiﬁcation Report, Notiﬁcation Type = 0x07, Event = 0x00 Tamper recover (press tamper

switch for 0.5s):!

Sensor Binary Report, Value = 0x00, Type = 0x08 Notiﬁcation Report, Notiﬁcation Type = 0x07,

Event = 0x00

Association Group2

If there is any device under Association Group2, the door sensor will send “BASIC SET”

command to control those devices when the door sensor is triggered. For example: when the door

sensor is triggered, it sends adjustable parameter “BASIC SET” command to a lamp under

Group2, you can adjust the lamp’s luminance through the parameters of this command; if the set

light-up time out (see the Conﬁguration Description), the sensor will send “BASIC

SET”command to turn-off the lamp.

When sensor is triggered:!

[Command Class BasicBasic Set,Value = 0xFF(default 0xFF, conﬁgurable, see the

Conﬁguration Description)] When light-up time out:!

[Command Class BasicBasic Set,Value = 0x00]

Conﬁguration Description

a) “Basic Set” conﬁguration!

If there is any device under Association Group2, the door sensor will send “Basic Set = value”

[email protected]



Altri manuali BeSense Accessori

BeSense

BeSense IM20 Zwave Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente