Biamp VOLTERA A Series Istruzioni per il montaggio
www.biamp.com
VOLTERA A Series
Installation and Set Up Guide
Product Information Sources
•This guide covers the installation and initial set up of the amplifier.
•Please see the product datasheets on Biamp.com for each Voltera amplifier’s
specifications.
•If you are installing the amplifier in an AV system managed by a Tesira DSP device,
you will need a copy of the Tesira Design Software. See page 17 for details.
Included in the Box
•0.3” euroblock connector plugs for the amplified outputs (yellow)
o2 plugs for the 2-channel amps. 4 plugs for the 4-channel amps.
•3.81mm audio input mating plugs
•Detachable IEC Power cord
•4 adhesive feet
•1 single device rack mounting bracket, 1 device rack mounting bracket, and 4
surface-mount brackets.
A 300.2 A 600.2 A 300.4 A 600.4 Analog Amplifiers
2 Voltera Amplifiers Installation and Set Up Guide
Installation Considerations
•Install the device away from heat sources, such as vents, radiators, heat registers, and
stoves.
•Do not exceed the maximum ambient operating temperature of 32° - 104° (0° - 40° C).
•Avoid installing near water or steam.
Device Layout
Front Panel
On / Off Power Button
Channels Status Display
(The number of channels varies by amplifier type)
Amplifier Type Identifier
Power Indicator Light
3 Voltera Amplifiers Installation and Set Up Guide
Front Panel LED Indicators
Power Indicator
Off
Green Light
Yellow Light
The amplifier is off.
The amplifier is powered
The amplifier is asleep
Channel Display Indicators
Off
Green
Yellow
Red
temp
This channel is
within safe
temperature
limits
N/A
Fan speed
medium
Fan speed max
limit*
This channel is
within safe
limits
N/A
Channel
limiting low to
medium
Channel
limiting high
signal
No signal
Signal
present**
The signal is 6
dB from
maximum
output
The signal is 1
dB from
maximum
output
mute
This channel is
unmuted
N/A
N/A
Mute Active
**A minimum signal strength of -56 dBU is required to register as present.
Back Panel LED Indicators
*Each channel’s LED indicator on the back panel combines the
signal present and the limiter indicators from its front panel
counterparts. Signal present is indicated with green. If the
signal is strong enough to engage the limiter, it replicates the
front panel yellow and red limit outputs.”
4 Voltera Amplifiers Installation and Set Up Guide
A 300.2 and A 300.2 Back Panels
The amplifiers share an identical panel layout
A 300.4 and A 600.4 Back Panels
Channels 3 and 4 gain controls
4, 3-pin input Ports
Logic input / output connectors
Voltage Control Input
Attenuator and High Pass Filter switches
4 Speaker output ports
Channel 2 output level control
Channel 1 gain control
2, 3-pin input Ports
Logic input / output connectors
Voltage Control Input
Attenuator and High Pass Filter switches
2 Speaker output ports
Channel 2 output level control
Channel 1 gain control
Limit / signal indicators
5 Voltera Amplifiers Installation and Set Up Guide
Included Mounting Brackets
1 Single-Device Rack Mounting Bracket
Biamp part number: 548.0468
1 Device Rack Mounting Bracket
Biamp part number: 548.0469
4 Surface Mounting Brackets
Biamp part number: 548.0470
6 Voltera Amplifiers Installation and Set Up Guide
Installation and Set Up Overview
Installation
Perform the procedures described in the Installation chapter to install the amplifier on a flat
horizontal surface or in an AV equipment rack.
✓Install in a location
•Freestanding, page 7
•Surface mount, page 8.
•A single amplifier in a 19-inch rack, page 9
•Dual amplifiers in a 19-inch rack mount, page 10
19-inch rack installation configurations using the included mounting brackets
✓Connect the amplifier
•Connect to its input, output, and other relevant devices in the system, page 12.
oThis section includes a description of the port functions and technical details.
oOptional: Adjust the output gain levels.
oSet the output power modes on each channel and set the High Pass Filter to on
or off.
•Attach and plug in the power cord, page 16.
Amplifier Set Up
✓Configure the amplifier
•Download the Tesira Design Software, page 17.
•Add the amplifier to the Tesira system and select its output speaker types, page 18.
7 Voltera Amplifiers Installation and Set Up Guide
Install Option: Freestanding
Place the amplifier on a flat horizontal surface.
1. Verify the surface is flat and level, and that the amplifier's power cord and connections
will be safely out of the way to avoid snagging, yanking, or crushing.
2. Attach the 4 included adhesive feet to the bottom of the amplifier. The 4 feet should be
attached near the 4 corners.
3. Place the amplifier on the surface
Advance to the connect the amplifier procedure on page 12.
8 Voltera Amplifiers Installation and Set Up Guide
Install Option: Surface Mount
Secure the amplifier to a flat surface using the surface mount brackets.
1. Verify the surface is flat and level, and that the amplifier’s power cord and connections
will be safely out of the way to avoid snagging, yanking, or crushing.
2. Use the included screws to fasten the 4 surface mount brackets to the four attachment
points on the bottom of the amplifier.
3. Place the amplifier on the surface and fasten the mounting brackets to the surface.
Advance to the connect the amplifier procedure on page 12.
9 Voltera Amplifiers Installation and Set Up Guide
Install Option: A single amplifier in a 19-inch AV rack
Install a single amplifier by itself in an AV equipment rack using the included Single-Device
Mounting Bracket and the Device Mounting Bracket.
1. Verify the installation rack space meets the temperature and spacing requirements in
the Installation section Consideration on page 2.
2. Attach the single-unit mounting bracket to the left or right side of the amplifier.
3. Attach the device mounting bracket to the opposite side of the amplifier.
4. Place the amplifier in the rack and use two of the included screws to secure the
mounting plate to the rack
Advance to the Connect the Amplifier procedure on page 12.
10 Voltera Amplifiers Installation and Set Up Guide
Option: Dual devices in a 19-inch rack
Install two amplifiers side by side in a standard AV rack using the Device Mounting Bracket
included with each unit and two of the included surface mounting brackets.
1. Verify the installation rack space meets the temperature and spacing requirements in
the Installation section Consideration on page 2.
2. Place both amplifiers side by side on lying their tops, with the bottom facing up. You are
about to fasten the amplifiers together for installation, so their front panels must face in
the same direction.
3. Attach two of the surface mounting brackets to the bottom of the two amplifiers on the
surface-mount attachment points where the amplifiers meet. Each bracket should cover
the adjoining mount points on the amplifiers.
Altri manuali per VOLTERA A Series
1
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Biamp Amplificatore
Biamp
Biamp Vocia VFOM-1 Manuale utente
Biamp
Biamp TC60 Manuale utente
Biamp
Biamp Vocia VA-4300CV Manuale utente
Biamp
Biamp T Series Manuale utente
Biamp
Biamp VOCIA VA-8600 Manuale utente
Biamp
Biamp CPA650 Manuale utente
Biamp
Biamp Vocia VA-2060 Manuale utente
Biamp
Biamp AMP-450BP Istruzioni operative originali
Biamp
Biamp PREZONE2 Istruzioni operative originali
Biamp
Biamp VOLTERA A Series Istruzioni per il montaggio
Biamp
Biamp DA28R Manuale utente
Biamp
Biamp POWERPAK PLUS+ Manuale utente
Biamp
Biamp MXA Series Manuale utente
Biamp
Biamp VOCIA VA-8600 Manuale utente
Biamp
Biamp Vocia VA-2060 Manuale utente
Biamp
Biamp Vocia VFOM-1 Manuale utente
Biamp
Biamp AUDIAFUSION Manuale utente
Biamp
Biamp TesiraXEL 1200.2 Istruzioni operative originali
Biamp
Biamp CPA650 Manuale utente
Biamp
Biamp CPA650 Manuale utente
