Biamp Nexia Series Manuale utente
Replacing the fan on a Nexia
This article explains how to replace a fan in a Nexia product. The Nexia has a single fan located on the right side of the
chassis (when viewed from the front). The fan should be replaced if it makes excessive noise (especially grinding or
groaning noises) or if it doesn't spin at all when the unit is powered on.
Replacement fans can be obtained from Biamp Systems, either as a warranty item or a spare part order. However, there
are several different fans available, depending on when the Nexia was manufactured. Please take note of the serial
number of the Nexia and call Biamp's Service department to ensure you receive the correct fan for your Nexia.
Required Tools
The following items are required to replace a Nexia fan:
• #1 Phillips screwdriver
• #2 Phillips screwdriver
• Replacement Fan (call Biamp Service department for correct part number)
Step by step
Follow the steps below to replace the fan. Click on any of the images to see a full-size view of the photo.
1. Unplug power to the Nexia.
2. Remove the Nexia from its rack or enclosure, if necessary.
3. Remove the three #4 sheet metal screws on the front of the chassis.
4. Remove the four #4 sheet metal screws on the rear of the chassis.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 1
5. Remove the two #4 sheet metal screws from each side of the chassis.
6. Remove the top cover and set it aside.
7. Remove the old fan by removing the four #6 screws holding the fan in place. Depending on the age of the Nexia
unit, these screws will be held in place by aircraft nuts or by thread-forming screws without the need for nuts. Note
the orientation of the fan before removing it, so that the replacement fan can be installed in the same orientation.
8. The fan has a 2-conductor wire that connects to the main board. Note the orientation of this connector so that the
new fan's connector can be installed in the same orientation. The correct orientation might be different than the
photo below. Disconnect the fan from its connector on the board and remove the fan from the chassis.
9. Install the new fan using the four #6 screws that held the old fan in place. Before installing the new fan, ensure that
the opening is clear. Also, please remember that only minimal tightness is needed for fan screws. Over-tightening
the screws can cause the fan to make excessive noise.
10. Plug the fan connector into the board, where the old fan connector was plugged in. Ensure that the polarity and
orientation of the connector is correct. Depending on the age of the unit, the correct orientation may look different
than the photos in this article.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 2
11. Replace the top cover, and replace all of the #4 sheet metal screws in the reverse order of how they were
removed.
12. Re-install the Nexia into its rack or enclosure, if necessary, and re-apply power to the Nexia. Confirm that the fan
spins normally and doesn't make excessive noise. If it makes excessive noise, try slightly loosening some of the
#6 screws that hold the fan to the chassis. Nexia fans are designed to exhaust air from the unit, so if the fan is
sucking air into the unit, then either the fan was installed backwards or the fan cable was plugged into the board
backwards.
Copyright 2013-2020 Biamp Systems http://support.biamp.com/ 3
Indice
Altri manuali Biamp Hardware per computer
Biamp
Biamp ADVANTAGE NMP200 Manuale d'uso e manutenzione
Biamp
Biamp Devio SCX Manuale utente
Biamp
Biamp ADVANTAGE NMP200 Manuale utente
Biamp
Biamp MSP11 Manuale utente
Biamp
Biamp QtPro Series Manuale utente
Biamp
Biamp Tesira SERVER Manuale utente
Biamp
Biamp TesiraFORTE Manuale utente
Biamp
Biamp VOCIA VI-6 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
