BILT HARD 10-INCH Manuale utente

10-INCH DRILL PRESS

IMPORTANT:

Your new tool has been engineered and manufactured to highest standards for dependability,

ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged,

trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use

your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.

INSTRUCTION MANUAL

Thank you for ordering our product. If you have any issue, please email with

your order ID to [email protected] or call (888) 680-2849

CONTENTS

3EMOCLEW

Introduction ..................................................................................................... 3

Speciﬁcations................................................................................................... 3

4YTEFAS

General Safety Rules........................................................................................ 4

Drill Press Safety Warnings ............................................................................. 6

Electrical Information....................................................................................... 8

BEFORE OPERATING 9

Unpacking & Packing List................................................................................ 9

Know Your Drill Press .................................................................................... 10

Assembly & Adjustment................................................................................. 11

OPERATION & MAINTENANCE 61

Operation ....................................................................................................... 16

Maintenance................................................................................................... 17

Troubleshooting Guide................................................................................... 19

Exploded View & Parts List............................................................................ 21

SPECIFICATIONS

Motor 120V, 60 Hz, 6.2A

Speeds 350-3,000 r/min. (RPM)

Swing 10"

Table Size 7-5/8 in. x 6-1/2 in.

Total Height 29"

INTRODUCTION

Thanks for purchasing the Drill Press. We know you are excited to put your tool to work, but ﬁrst, please take

a moment toread through the manual. Safe operation of this tool requires that you read and understand this

operator’s manual and all the labels afﬁxed to the tool. This manual provides information regarding potential safety

concerns, as well as helpful assembly and operating instructions for your tool.

NOTE: The following safety information is not meant to cover all possible conditions and situations that may occur.

reserves the right to change this product and speciﬁcations at any time without prior notice.

Keep this manual available to all users during the entire life of the tool and review it frequently to maximize

safety for both yourself and others.

SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. The safety symbols and the explanations

with them deserve your careful attention and understanding. Always follow the safety precautions to reduce the

risk of ﬁre, electric shock or personal injury. However, please note that these instructions and warnings are not

substitutes for proper accident prevention measures.

GENERAL SAFETY RULES

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂammable liquids,

gases or dust. Power tools create sparks which may ig-

nite the dust or fumes.

3. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never mod-

ify the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfac-

es such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

3. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of elec-

tric shock.

4. Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric

shock.

5. When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

6. If operating a power tool in a damp location is un-

avoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of elec-

tric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

power tool while you are tired or under the inﬂuence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

2. Use personal protective equipment. Always wear

eye protection. Protective equipment such as a respira-

tory mask, non-skid safety shoes and hearing protection

used for appropriate conditions will reduce the risk of

personal injury.

3. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the switch or

energizing power tools that have the switch on invites

accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jew-

elry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

GENERAL SAFETY RULES

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

2. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained us-

ers.

5. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s opera-

tion. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into ac-

count the working conditions and the work to be per-

formed. Use of the power tool for operations different

from those intended could result in a hazardous situa-

tion.

8. Use clamps to secure your workpiece to a stable

surface. Holding a workpiece by hand or using your

body to support it may lead to loss of control.

9. KEEP GUARDS IN PLACE and in working order.

SERVICE

1. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is main-

tained.

CALIFORNIA PROPOSITION 65 WARNING

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities may contain

chemicals, including lead, known to the State of Califor-

nia to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling. Some examples of

these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies depending on

how often you do this type of work. To reduce your ex-

posure to these chemicals, work in a well-ventilated area

with approved safety equipment such as dust masks

specially designed to ﬁlter out microscopic particles.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

DRILL PRESS SAFETY WARNINGS

1. TOOL PURPOSE. This drill press is designed to

drill through metal and wood. Drilling through other

materials could result in ﬁre, injury, or damage to the

workpiece. Using the machine for any other purpose

for which it is not designed may result in serious in-

juries, machine damage and voiding of the warranty.

2. MACHINE MOUNTING. For operation safety, the

drill press must be securely mounted onto a ﬂat and

stable surface or stand.

3. PERSONAL SAFETY.

• Always wear ANSI Z87.1-approved glasses with

side shields, hearing protection, and a dust mask.

• Do not wear loose clothing or jewelry, as they

might get drawn in by the tool. Tie back long hair.

• Do not wear gloves while operating this machine.

4. ELECTRIC CORDS. Keep cords away from heat,

oil, sharp edges, and moving parts of the tool. Have

an electrician replace or repair damaged or worn

cords immediately.

5. TOOL & ACCESSORIES INSPECTION. Before op-

eration, check the tool and accessories for any dam-

age or missing parts. Do not use the tool if any part

is missing or damaged. Make sure all adjustments

are correct and all connections are tight. Keep all

guards in place.

6. DRILLING ACCESSORIES.

• Make sure the drill bit is not damaged before

use, only use undamaged drill bits

• Make sure the drill bit is securely locked in the

chuck before turning ON.

• Make sure the chuck key is removed from the

chuck before turning ON.

• Use clamps or a vise to secure a workpiece to

the table. This will prevent the workpiece from

rotating with the drill bit.

7. Make sure the table lock is tightened before start-

ing the drill press.

8. WORKPIECE REQUIREMENTS.

• Only stand workpieces sturdy enough to with

stand the force of the drill bit.

• Inspect workpiece for imperfections, nails,

staples, etc. before drilling. Never drill stock that

has questionable imperfections or embedded

foreign objects.

• Do not drill materials without a ﬂat surface un

less a suitable support is used (clamp or vise).

9. PREVENTING ACCIDENTAL STARTING. Make sure

the power switch is in the OFF position prior to plug-

ging in the machine. Always make sure the power

switch is in the OFF position and the machine is un-

plugged when doing any cleaning, assembly, setup

operations, or when not in use.

10. Do not operate this tool until it is completely as-

sembled and installed according to the instructions.

11. Remove scrap pieces and other objects from the

table before turning ON the drill press.

12. DRILLING THE WORKPIECE.

• Allow spindle to reach full speed before drilling

the workpiece.

• Never start the machine with the drill bit pressed

against the workpiece.

• Adjust the table or depth stop to avoid drilling

into the table.

• Set the drill press to the speed that is appropriate

for the material being drilled.

13. Do not touch moving pieces. Keep hands away

from the drill bit during operation. If cleaning is nec-

essary, turn off the machine and use a brush to re-

move sawdust and chips instead of your hands.

14. Never perform layout, assembly or set-up work

on the table while the machine is ON.

WARNING! Do not operate the power tool until you have read and understood the following instructions and

the warning labels.

DRILL PRESS SAFETY WARNINGS

15. After turning off the drill press, wait until the

spindle comes to a complete stop before touching

the workpiece. Always turn the drill OFF before re-

moving scrap from the table.

16. Before leaving the machine, always turn OFF and

unplug the machine, remove the drill bit, and clean

the table. Turn Off and unplug the machine before

cleaning, making adjustments or changing drill bits.

Accidental start-ups may occur if the tool is plugged

in during an accessory change or adjustment.

17. CLEANING. Never use solvents to clean plastic

parts. Solvents could dissolve or otherwise dam-

age the material. Use only a soft damp cloth to clean

plastic parts.

18. REPLACEMENTS. Should any component of

your drill press be missing/damaged or fail in any

way, shut OFF the switch and remove the plug

from power supply outlet. Replace the missing,

damaged, or failed parts using only identical re-

placement parts before resuming operation.

CALIFORNIA PROPOSITION 65 WARNING

Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities may

contain chemicals, including lead, known to the

State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies depending

on how often you do this type of work. To reduce

your exposure to these chemicals, work in a well-

ventilated area with approved safety equipment such

as dust masks specially designed to ﬁlter out micro-

scopic particles.

WARNING! Do not operate the power tool until you have read and understood the following instructions and

the warning labels.

ELECTRICAL INFORMATION

AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS

25 ft. 50 ft. 100 ft. 150 ft.

2.3A 18 gauge 16 gauge 16 gauge 14 gauge

3. Check

with a licensed electrician or service personnel if you do not completely

understand the grounding instructions or whether the tool is properly grounded.

4. Use only three-wire extension cords

that have three-pronged plugs and outlets

that accept the tool’s plug (INSERT CR). Repair or replace a damaged or worn cord

immediately.

CAUTION!

In all cases, make certain the outlet in question is properly grounded. If

you are not sure, have a licensed electrician check the outlet.

GUIDELINES AND RECOMMENDATIONS FOR EXTENSION CORDS

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown

, grounding provides the path of least resistance for an electric

current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an

equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet

that is properly installed and grounded in accordance with ALL local codes and ordinances.

1. Do not modify the plug provided.

If it will not ﬁt the outlet, have the proper outlet installed by a licensed

electrician.

2. Improper connection

of the equipment grounding conductor can result in electric shock. The conductor

with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or

replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor

to a live terminal.

1. Examine extension cord before use. Make sure your extension cord is properly wired and in good condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed person before using it.

2. Do not abuse extension cord. Do not pull on cord to disconnect from receptacle; always disconnect by pulling on

plug. Disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.

Protect your extension cords from sharp objects, excessive heat and damp/wet areas.

3. Use a separate electrical circuit for your tool. This circuit must not be less than a 12-gauge wire and should be

protected with a 15A time-delayed fuse. Before connecting the motor to the power line, make sure the switch is in

the OFF position and the electric current is rated the same as the current stamped on the motor nameplate. Running

at a lower voltage will damage the motor.

Fig. 1

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An un-

dersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the

correct size to be used according to cord length and ampere rating. When in doubt, use a heavier cord. The smaller

the gauge number, the heavier the cord.

UNPACKING & PACKING LIST

UNPACKING

With the help of a friend or trustworthy foe, carefully remove the Drill Press from the packaging. Make sure to take

out all contents and accessories. Do not discard the packaging until everything is removed. Check the packing list

below to make sure you have all of the parts and accessories.

PACKING LIST

ASSEMBLY / ADJUSTMENT TOOLS

The tools listed below are not included but are required for either assembly or adjustment:

• Adjustable wrench

• Hammer and block of wood or rubber mallet, or dead-blow hammer

WARNING! Do not plug in or turn on the tool until it is fully assembled according to the instructions. Failure

to follow the safety instructions may result in serious personal injury.

Head / Motor Assembly....................................1

Table Locking Handle.......................................1

Table Asssembly...............................................1

Base.............................................................1

Column Assembly............................................1

Chuck...............................................................1

Chuck Key........................................................1

Feed Handles...................................................3

Hex Wrench.....................................................2

Hex bolt M 8×20...............................................3

10.

Depth gauge.....................................................1

11.

Column collar...................................................1

12.

Table adjustment handle...................................1

13.

Worm gear........................................................1

14.

KNOW YOUR DRILL PRESS

TOOL PURPOSE

Drill clean, precise cylindrical holes into workpieces or enlarge existing holes with your Drill Press. Refer to the fol-

lowing diagrams to become familiarized with all the parts and controls of your Drill Press. The components will be

referred to later in the manual for assembly and operation instructions.

DRILL PRESS

Housing Cover

Chuck Key

Chuck

Motor

Feed Handle

Belt Tension

Base

Table assembly

Table Lock

ON/OFF Switch

Column

Indice

Altri manuali BILT HARD Utensili elettrici

BILT HARD

BILT HARD TL-G-PC10 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale