Bimmer Tech E60 Manuale utente

Thank you for purchasing BimmerTech products! We strive to deliver the most functional,

reliable and high quality BMW retrofit upgrades on the market. Our kits are do it yourself

friendly, but if you're not fond of working on your car don't worry. You can always take your

freshly purchased kit along with these installation instructions to one of our recommended

installers or to any other professional installer in your area. We offer full technical support

all the way up to a successful installation finale.

If you will be installing the kit yourself then it is recommended to do so in a clean,

spacious, well lit and climate controlled garage without pressing time constraints. The

installation does involve disassembling many areas of your vehicle so it's best to take your

time, be gentle, careful and diligent in keeping track of which screw and clip came from

where to reinstall the parts correctly.

Please read the instructions in full before beginning the installation and have a thorough

look at the below installation video. While it is not explicitly for your vehicle it is very

similar.

Rear View Camera and Fronr View Camera Installation Video:

https://www.youtube.com/watch?v=SksfQZnKILg

The dip switches on the camera module should be set as follows:

#1 - always ON

#2 - OFF (for connecting the Front View Camera to AV1 input)

#3 - ON (if set to ON AV2 is disabled)

#4 - ON(if set to ON AV3 is disabled)

#5 - ON/OFF (default OFF)

#6 - ON/OFF (default OFF)

#7 - ON (if set to ON the rear view camera mode is enabled)

#8 - always OFF

If the screen does not work or the rear view camera picture does not show in reverse

please try one of the below settings for dip switches #5 and #6:

#5- ON, #6 - ON

#5- ON, #6 - OFF

#5- OFF, #6 - ON

#5- OFF, #6 – OFF

Every time you change dip switches please disconnect the POWER connector from the

MMI to allow the DIP changes to take effect.

Use the attached PDF to install the camera in the trunk lid and run the camera wiring to

the dashboard.

The multimedia interface you received is different from the one in the PDF, so please

follow the below instructions to connect it to the screen:

The rear camera extension cable splits into two cables (yellow RCA plug and white

connector) which should be connected:

- white connector directly to the multimedia interface R-CAM

- yellow RCA to yellow RCA in the AV (IN/OUT) wiring

The front camera extension cable connects to a adaptor cable (that ends with a yellow

RCA plug and red and black power wires) and these should be connected:

- yellow RCA to AV1 input

- red wire to red wire incoming to the MMI power port with a tap-in connector

- black wire to black wire incoming to the MMI power port with a tap-in connector

Connect the small 4-button keypad to the multimedia interface and hide it somewhere

where you can easily access it in the future.

Next please remove the screen and unplug the video cable from the screen. It's the one

with metal connector.

This cable has to be connected to the multimedia interface to LCD-IN.

Then connect the multimedia interface back to the screen (from LCD-OUT to the screen).

The next cable that has to be connected to the multimedia interface is the 10-wire POWER

cable included in the kit.

You need to connect just 4 wires from this connector and they should be tapped into the

wires going to the original screen connector (black connector).

This black connector has 4 wires. When you disconnect the connector from the screen and

slide out the subconnector you will see pin numbers marked on the connector.

Please connect the power wires from the module to the wires going to the screen in the

following way:

pin 5 from the power wire (yellow wire) should be tapped into the wire going to pin 6 in the

black screen connector

pin 6 from the power wire (white wire) should be tapped into the wire going to pin 5 in the

black screen connector

pin 9 from the power wire (black wire) should be tapped into the wire going to pin 3 in the

black screen connector

pin 10 from the power wire (red wire) should be tapped into the wire going to pin 1 in the

black screen connector

Front View Camera + extension cable + RCA/Power adaptor cable + Tap-In connectors

Rear view camera extension cable + Rear View Camera (RVC) embedded in the trunk

handle:

Front Camera Installation

Once again the F30 video installation guide will offer you invaluable information on the

front camera installation process in your E60:

https://youtu.be/SksfQZnKILg?t=11m57s

Drop the plastic area shown below. Run the wires under the plastic by the foot well of the

driver’s seat, being careful not to interfere with the airbag.

The simplest and most efficient way to route the Front View Camera wire through the

firewall is to drill a hole in the existing grommet, as shown below. Be sure to drill a large

enough hole (yellow dot), so that the plastic clip will easily fit through, while being

extremely careful not to make contact with any other wires.

Once you’ve drilled through the grommet, use a sturdy wire or a thin hanger to route the

wire through the grommet.

Since your vehicle has a mesh grille you can simply unscrew the camera lens and install it

through the grille mesh from the inside and screw it back together.

Then connect the camera to the extension cable and heat shrink the connection. You

should be able to do this without removing the bumper cover. Please have the battery

disconnected before doing this – we don't want the fans to turn on while you're working

under the hood.

Route the camera cable around the engine bay all the way to the rubber grommet in the

firewall as space permits, and proceed to run it up to the MMI module, connecting it to the

previously installed adaptor cable.

Once all cables are connected as described you can reconnect the earth lead to the

negative battery terminal power up the car and check if everything works.

To engage the Front camera press the Mode button connected to the MMI module or long

press the down button on your steering wheel.

Make sure the front camera picture is unobstructed by the grille and not upside down. If

the camera works fine you can now secure the camera cable with cable ties to prevent it

from moving around. After the cable is in its final location seal the hole you made in the

grommet with black silicone. Proceed to reassemble all of the trim pieces.

To turn on the reverse camera simply engage reverse gear.

Congratulations! Your Installation is now complete.

If you have any questions or need assistance do not hesitate to contact us via e-mail:

[email protected]

Indice

Altri manuali Bimmer Tech Elettronica per automobili

Bimmer Tech

Bimmer Tech WCPAA-BM12 Manuale utente

Manuali Elettronica per automobili popolari di altre marche

GoldCruise

GoldCruise GC90Ci Manuale utente

DRG

DRG LC 120 Manuale utente

Blue Ox

Blue Ox BX8848 Manuale utente

Dometic

Dometic MAGICWATCH MWE890K Manuale utente

Perfect Power

Perfect Power SMT8-T5 Manuale utente

Honeywell

Honeywell Thor VM3A Manuale utente

Waeco

Waeco MagicWatch MWE250 Manuale utente

Rydeen

Rydeen BKM091 Manuale utente

Skoda

Skoda 5E0 054 630 Manuale utente

VDO

VDO SENDER UNIT 2159-0 Manuale utente

iDataLink

iDataLink maestro Rr Manuale utente

Audiovox

Audiovox PRO-PDA15 Manuale utente

Movon

Movon MDAS-3LFFHD Manuale utente

Pioneer

Pioneer Comfort adapter CA-D-PI.150 Manuale utente

Dietz

Dietz 1110 Manuale utente

Crux

Crux RVCFD-79 Manuale utente

Nonda

Nonda ZUS Manuale utente

iDataLink

iDataLink Maestro Manuale utente