BioTrack BioExterior Manuale utente
www.BioTrackSoftware.com
BioExterior
INSTALLATION GUIDE
The following precautions are to keep user’s safe and prevent any damage. Please read carefully before
installation.
•Do not install the device in an area subject
to direct sunlight, humidity or dust
•Do not place a magnet near the product.
Magnetic field from magnets, CRT, TV, monitor
or speaker may damage the device. •Do not place the device next to
heating equipment.
•Be careful not to let liquid like
water, drinks or chemicals leak
inside the device.
•Clean the device often to
remove dust on it
•Do not let children touch the
device without supervision.
Safety Precautions
www.BioTrackSoftware.com
The following precautions are to keep user’s safe and prevent any damage. Please read carefully before
installation.
•Do not drop the device. •Do not disassemble, repair or
alter the device. •Do not use the device for any
other purpose than specified.
•Do not damage the device •In cleaning, do not splash water on the
device but wipe it out with smooth cloth
or towel.
•Contact your nearest dealer in
case of a trouble or problem.
Safety Precautions
www.BioTrackSoftware.com
&ingerprint readers will give optimal results for fingerprint matching if the following recommendations and suggestions
are followed.
Select a finger to enroll
It is recommended to use an index finger or a middle finger.
Thumb, ring or little finger are relatively difficult to place in the correct position
How to place a finger on a sensor
Place a finger such that it completely covers the sensor area with maximum contact.
Place core of the fingerprint at the center of the sensor. The core of a fingerprint is a center where the spiral of ridges is
dense.
Usually core of fingerprint is the opposite side of the lower part of a nail.
Place a finger such that the bottom end of a nail is located at the center of a sensor.
If a finger is placed as shown in the right, only a small area of a finger is captured. So it is recommended to place a finger as
shown on the left.
How to Place a Finger
www.BioTrackSoftware.com
Tips for different fingerprint conditions
Fingerprint products are designed to verify fingerprints with highest security irrespective of the
conditions of the skin of the finger. However, in case a fingerprint is not read on the sensor, please refer to the
followings tips.
•If a finger is stained with sweat or water, scan after wiping moisture off.
•If a finger is covered with dust or impurities, scan after wiping them off.
•If a finger is way too dry, please blow some warm air from your mouth on the finger tip.
Tips for fingerprint enrollment
In fingerprint recognition, enrollment process is very important. When enrolling a fingerprint, please try to place the
finger correctly with utmost care.
In case of low acceptance ratio, the following actions are recommended.
•Delete the enrolled fingerprint and re-enroll the finger.
•Enroll the same fingerprint again.
•Try another finger if a finger is not easy to enroll due to scar or cuts.
In case of an enrolled fingerprint cannot be used due to injury or if the hand is full, it is recommended to enroll more
than two fingers per user.
How to Place a Finger
www.BioTrackSoftware.com
Fingerprint database
Register finger Identification Feature extraction
Verify feature
Verified
successfully
Verification
failed
Create
Please try again !
Thank you !
Event logs
Open door
Door closed
Stored
How Does Reader work
www.BioTrackSoftware.com
Basic Contents
Wall Mounting Screws –3 pcs. Wall Plugs–3 pcsScrew Driver –1 pc.
Star-shape Screw for
Mounting Plate -2 pcs Mini-USB Cable -1 pc
2 pin, 5 pin, 7 pin, 10 pin
cables –each 1 pc
Mounting Paper
Software CD
BioExterior Installation Guide
Product Contents
www.BioTrackSoftware.com
Optional accessories
Weigand Card Reader Exit ButtonSlave Fingerprint Reader
RS485 Convertor
12VDC, 3A Power
Adaptor
Prox Card
Product Contents
www.BioTrackSoftware.com
Front View Side View
USB-host
OLED Screen
3 x 5 Keypads
Doorbell/LED
Fingerprint Reader
Reset
Product PIN Diagram
www.BioTrackSoftware.com
Bottom View
Back View
Star-shaped screw hole for fixing reader to the back plate
Tamper switch
(Magnetic Contact)
Cables and Connectors
Product PIN Diagram
www.BioTrackSoftware.com
Indice
Altri manuali BioTrack Controllori di accesso IP
