Bircher Reglomat ProLoop Lite Manuale utente















22.5

ProLoop Lite

Loop detector for industrial doors and gates and car parks

Translation of the original instruction

General

1Safety instructions

3Connect electrical equipment

2Mechanical mounting in the switch cabinet

ENGLISH

354822B

06/16

Information – light emitting diode

LCD display

“Mode” key

“Data” key

Connecting terminals

Type plate

– These devices and their accessories may only be operated in accordance

with the operating instructions (intended use).

– These devices and their accessories may only be placed in operation by

trained and qualied personnel.

– These devices may only be operated with the operating voltages and

parameters intended for them.

– If malfunctions occur that cannot be eliminated, place the device out of

operation and send it in for repair.

– These devices may only be repaired by the manufacturer. Tampering and

alterations are not permitted. This will invalidate all guarantee and war-

ranty claims.

The ProLoop Lite is mounted in the switch cabinet on a 35 mm H-rail in accordance with EN 50022. The terminals can be plugged in and coded.

The loop connection wiring to a loop detector must be twisted at least 20 times per meter.

Please wire the device according to the wiring diagram.

Ensure correct assignment of the terminals and that the power supply is right in accordance with the type plate on the device.

Power supply Loop connection

1-channel device

Loop connection

2-channel device

Output 1 Output 2

˜⁄

−

common

4Value and parameter setting options

General

The settings of the ProLoop Lite devices in this chapter are depicted and explained using the 1-loop device.

The settings for loop 2 of a 2-loop device should be made using the corresponding method.

3.1 Terminal connection diagram

4.1 Value and parameter setting options

4.2 Basic functions of output relay status 0(setting, see table 4.8)

4.3 Time functions 1, time unit 2and time factor 3 (settings, see table 4.8)

4.4 Sensitivity 4(setting, see table 4.8)

4.5 Automatic sensitivity boost ASB S(setting, see table 4.8)

4.6 Frequency 6(setting, see table 4.8)

4.7 Switching from operating to conguration mode

Standard display

1-loop device

Standard display

2-loop device

112

Explanation of the LEDs

Info

Red + Green Start-up phase

conguration

Green Operation

Green ashing Output 1 or / and

2 activated

Flashing red Error

Explanation of the LCD display

Loop 2

Loop 1

Function

Example:

Time

function set

Example:

Parameter

“h” set

Parameter Loop unactivated Loop activated Fault

1Door and gate

2Barrier

3Quiescent

current

Activation of the

loop pulls the relay

on; the relay drops

off when the loop

is exited. t = typically ms or s

Switch-on delay:

When the loop is

activated, the relay is

pulled on after the time t

and drops off when the

loop is exited.

t = typically ms or s

Switch-o delay:

When the loop is

activated, the relay is

pulled on drops off after

time t tafter the loop is

exited.

t = typically ms or s

Activation pulse:

When the loop is

activated, the relay

is pulled on and

drops back off

after time t.

t = typically ms or s

Exit pulse:

When the loop is exited,

the relay is pulled on and

drops back off after time

t = typically ms or s

Maximum presence:

When the loop is

activated, the relay is

pulled on and drops back

off when exited, but not

later than after time t.

t = typically ms or s

The sensitivity Sof the loop detector can be adjusted in 9 steps:

S1 = lowest sensitivity

(➝much metal, low recognition distance)

S9 = highest sensitivity

(➝ little metal, large recognition distance)

S4 = factory setting

ASB (= Automatic Sensitivity Boost).

ASB is required in order to be able to detect trailer drawbars after activation.

Four different frequencies F1, F2, F3 and F4 can be set. This helps to prevent crosstalk with adjacent loops. Factory setting: F4.

1-loop device

Display after

start-up:

1Touch the «Mode» button

once to change to conﬁgura-

tion mode

Mode 1

2-loop device

Display after

start-up:

12Touch the «Mode» button

once to change to conﬁgura-

tion mode

Mode 1

Loop 1 is

selected

Mode 2

Loop 2 is selected

(Back to automatic mode: Press and hold Mode button > 1 second)

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

Table Settings Button

operation

parameter

Data Data Data Data Data Data

Function LCD

Display

Button operation

functions

AOperating

mode

Mode

Operating mode 1

0Basic function 1

Mode

Door and gate* 1Barrier

Quiescent current 1

1Time function 1

Mode

∞* 1Switch-on delay

Switch-off delay

1Loop activation

pulse

1Loop exit pulse

1Maximum

presence

2Time unit

Mode

With time

function th (∞),

this display

does not appear

0.1 second 11 second*

1 minute 11 hour 1

Note:

Time unit multiplied by time factor

gives the set time.

3Time factor 1

Mode

With time

functionth(∞),

this display

does not appear

1 * 1

Set value between 1 and 99 by touching or holding the «Data» button

4Sensitivity 1

Mode

Sensitivity =

responsiveness

4 * 1

Set value between 1 (lowest ) and 9 (highest sensitivity) by touching or holding the “Data” button

5Automatic

sensitivity

boost ASB

Mode

ASB stands for

Automatic

Sensitivity

Boost

Switched off* 1Switched on 1

6Frequency 1

Mode

Frequency F1

Frequency F2

Frequency F3 1Frequency F4* 1

*Factory setting

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

Loop

Relay

4.8 Conguration mode

Note on 2-loop device: For each function after Loop 1 is set, the parameters of Loop 2 are set (perform settings similarly).

5Error display

6Reset

7Technical data

8EC Declaration of Conformity

9Contact

Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen

Following directives have been observed: RoHS 2011/65/EU, RED 2014/53/EU

Product variants: ProLoop Lite 1.x, ProLoop Lite 2.x

Bircher Reglomat AG

Wiesengasse 20

CH-8222 Beringen

www.bircher-reglomat.com

When an error occurs, the operating mode “A” and the error display “E” are shown alternatingly.

The LED changes to ashing red.

Mode

2 seconds Reset 1 (recalibration)

The loop(s) is/are recalibrated.

Power supply

voltage/

power consumption

24 VDC 24 VDC -10% to +20%,

max. 1.5 W

230 VAC 230 VAC ± 10%, 50 Hz,

max. 2.9 VA

Loop inductiveness Max. 20 to 1000 µH

Ideally 80 to 300 µH

Loop power line For 20-40 µH: max. 100 m with 1.5 mm2

For >40 µH max. 200 m with 1.5 mm2

Min. twisting 20 times per metre

Loop resistance < 8 ohms with connection wire

Output relay (loop) Max. 240 VAC; 2 A / 30 VDC; 1 A; AC-1

Dimensions 22.5 x 92 x 85 mm (W x H x D)

Housing mounting Direct DIN rail mounting

Connection type Screw-in terminals

Protection class IP 20

Operating

temperature

-20°C to +60°C

Storage

temperature

-40°C to +70°C

Air humidity < 95% non-condensing

Danish seller:

Swissdoor ApS

Stenhuggervej 2

DK-5471 Soendersoe

Denmark

Tel.: +45 86 28 00 00

[email protected]

www.swissdoor.dk

Altri manuali Bircher Reglomat Sensore di sicurezza

Bircher Reglomat

Bircher Reglomat Merkur 2 Series Manuale utente

Bircher Reglomat

Bircher Reglomat EsGate 2 Manuale utente

Bircher Reglomat

Bircher Reglomat ProLoop 2 Manuale utente

Bircher Reglomat

Bircher Reglomat PrimeTec B Manuale utente

Bircher Reglomat

Bircher Reglomat DI1-Pro V2 Manuale utente

Bircher Reglomat

Bircher Reglomat MERKUR SE Manuale utente

Bircher Reglomat

Bircher Reglomat MERKUR Manuale utente

Bircher Reglomat

Bircher Reglomat RK 31C-PWH Manuale utente

Bircher Reglomat

Bircher Reglomat RBM 2 Manuale utente

Bircher Reglomat

Bircher Reglomat Hercules 2 Manuale utente

Bircher Reglomat

Bircher Reglomat ProxySwitch Manuale utente

Bircher Reglomat

Bircher Reglomat Herkules 2 Manuale utente

Bircher Reglomat

Bircher Reglomat US beam Supplemento

Bircher Reglomat

Bircher Reglomat PrimeScan B Supplemento

Bircher Reglomat

Bircher Reglomat Herkules 2E Manuale utente

Bircher Reglomat

Bircher Reglomat PrimeTec B Manuale utente

Bircher Reglomat

Bircher Reglomat PrimeMotion B Manuale utente

Bircher Reglomat

Bircher Reglomat Jupiter Manuale utente

Bircher Reglomat

Bircher Reglomat ProLoop Manuale utente

Bircher Reglomat

Bircher Reglomat ProLoop Manuale utente

Bircher Reglomat

Bircher Reglomat Swissdoor PrimeMotion B Manuale utente

Bircher Reglomat

Bircher Reglomat Reflex ES Manuale utente

Bircher Reglomat

Bircher Reglomat ESM Manuale utente

Bircher Reglomat

Bircher Reglomat EasyMotion Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente