Black & Decker VEC156BD Manuale utente

VEC156BD

53SB

E231887

VEC156BD_Manual_022305 4/11/05 6:02 PM Page 8

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-877-571-2391

BEFORE YOU CALL, HAVE THE CATALOG No,

AVAILABLE. IN MOST CASES, A REPRESENTATIVE

CAN RESOLVE THE PROBLEM OVER THE PHONE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

ii iii

IMPORTANT SAFETY INSTRUCTIONS

WARNINGS

1. All halogen lights give off heat. Never place the light face-down on any surface when lit.

2. Never look directly into the light or shine the light into another person’s eyes.

3. Replace bulb with type indicated in specifications or a 6 volt H3 quartz halogen bulb.

4. Do not immerse this spotlight in water. This unit is not waterproof — it is water resistant.

5. Do not substitute power cords or charging adapters. Only charge with supplied AC and DC

charging adapters. Charging adapters for this unit supply 12 volts DC.

6. Keep children away from spotlight. This is not a toy!

7. Lens gets very hot when spotlight is operating. Do not touch lens while operating.

8. Keep combustibles away from spotlight lens — extreme heat can cause fires.

9. Keep sharp objects away from lens — it is glass and can break.

10. Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.

11. Dispose of unusable batteries in a responsible manner. See battery disposal section.

12. Do not crush, cut, pull or expose charging adapter cords to extreme heat.

13. Position charging adapter cords so that they do not become entangled or become a safety hazard.

Keep charging adapter cords away from sharp edges.

14. Do not operate while recharging.

CAUTIONS

• Use only with AC or DC charging adapters that are provided with unit. Plug in the charging adapter

at the spotlight first, then plug into the charging source.

• Do not overcharge:

– AC recharge up to 12-14 hours maximum.

– DC recharge up to 3-4 hours maximum.

• Use in a dry location only.

• There are no user-serviceable parts inside.

• RISK OF FIRE/ELECTRIC SHOCK — do not plug in a power supply without the bulb lens and cover in

place.

SAVE THESE INSTRUCTIONS

VEC156BD_Manual_022305 4/11/05 6:02 PM Page ii

iv 1

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Recharging the Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Charging from a 120 volt AC Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Charging from a 12 volt DC Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Spotlight Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Battery Replacement/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

DC Plug Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INTRODUCTION

Thank you for purchasing the

Cordless, Rechargeable 1,000,000 Power

Series

™

Spotlight.

Please read this guide carefully before use to ensure optimum

performance and to avoid damage to the unit.

FEATURES

• Powerful, focused, replaceable quartz halogen bulb in spotlight

• 3-position electronic spotlight dimmer control to conserve power and extend

runtimes

• Trigger Switch Lock locks the Trigger Switch in the OFF position or ON position

(maintaining spotlight operation without depressing trigger)

• Rubber safety guard (bezel) around lens protects spotlight

• Comfortable pistol grip

• Convenient carry lanyard

• Battery Charge Level Indicator displays battery charge level while charging or

whenever the spotlight is turned on

• UL listed, built-in 120 volt AC charging adapter

• Fused DC recharge/power cord

• Rechargeable, sealed lead acid battery (non-spillable)

Note: This unit is shipped in a partially charged state. Charge unit BEFORE first use

using the AC charger for 10 hours or until the green Battery Charge Level

Indicator LED lights. Charge after each use until green LED lights.

VEC156BD_Manual_022305 4/11/05 6:02 PM Page iv

OPERATING INSTRUCTIONS

To turn the cordless spotlight on depress the Trigger Switch. Depressing the Trigger

Switch at one-second intervals advances the brightness level from dim to brightest.

To lock the trigger into the ON position pull the Trigger Switch and move the Trigger

Switch Lock down. This will lock the trigger into the ON position. To shut it off, simply

move the Trigger Switch lock up to the OFF position.

PERIODIC MAINTENANCE

All batteries lose charge with time, especially when they are warm. AC recharge is

recommended every two months, when not in frequent use. Use the AC recharger and

charge for the recommended time. If the unit gets dirty, gently clean the outer surfaces

of the spotlight unit with a soft cloth moistened with a mild solution of water and

detergent. Periodically inspect the condition of the recharge adapters, connectors and

wires. Replace any components that may have become worn or broken.

RECHARGING THE SPOTLIGHT

Charging From a 120 Volt AC Source

To recharge, plug a 120 volt AC household extension cord into the 120 volt AC

Recharger on the back of the unit and charge for 12-14 hours or until the green

Battery Charge Level Indicator LED lights.

Charging From a 12 Volt DC Source

Plug the DC fused Recharge/Power Adapter (included) into the Recharge Port.

RECHARGE PORT

BUILT-IN 120V AC

CHARGER

BATTERY CHARGE

LEVEL INDICATOR

HOUSEHOLD EXTENSION CORD

(NOT INCLUDED)

TRIGGER SWITCH

LOCK

3/4 View

Back View

12 Volt DC Charging Adapter

BUILT-IN

120 VOLT AC

CHARGER

SMART

ELECTRONIC

DIMMER

SWITCH

RUBBER BEZEL

CARRY

LANYARD

DC RECHARGING

PORT

TRIGGER SWITCH

LOCK

PISTOL GRIP HANDLE

QUARTZ HALOGEN

BULB

VEC156BD_Manual_022305 4/11/05 6:02 PM Page 2

8. Using the screwdriver, loosen the retaining screw to remove the bulb from the

reflector (no need to completely remove this screw).

9. Lift out the bulb and detach wire.

10. Insert the replacement bulb into the reflector’s flange.

11. Put back and secure the hairpin retaining wires.

12. Connect the bulb power wire to the red power wire.

13. Tighten the retaining screw on the flange.

14. Place the reflector in position in the body of the spotlight.

15. Replace the rubber “O” ring in the groove around the perimeter of the reflector.

16. Replace glass and retaining ring so that the screw holes are aligned.

17. Secure retaining ring with two screws.

18. Replace the rubber bezel

19. Depress the Trigger Switch to ensure proper operation of spotlight.

CAUTION

To reduce the risk of electric shock only replace bulb with 55 watt 6

volt H3 bulb only.

Battery Replacement/Disposal

Battery Replacement

Battery should last the service life of the unit. Contact Technical Support at (800)

618-5178 for any information you may need.

Safe Battery Disposal

Contains a maintenance-free, sealed, non-spillable, lead acid

battery, which must be disposed of properly. Recycling is required

— contact your local authority for information. Failure to comply

with local, state and federal regulations can result in fines or

imprisonment. For more information on recycling this battery,

call toll-free (877) 288-7722.

CONTAINS SEALED,

NON-SPILLABLE BATTERY

Figures 2A & 2B

HAIRPIN RETAINING

WIRES

BULB

REFLECTOR

PHILLIPS

HEAD

SCREWS

Insert the power plug into the accessory outlet of your vehicle or other 12 volt DC

power source.

Make sure the spotlight is OFF and the Trigger Switch is in the OFF position

(not depressed).

Allow approximately 3-4 hours charging time.

Recharge until the green Battery Charge Level Indicator LED lights.

Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is

12 volt DC. The DC source should be able to supply at least one-half amp at

12 volt DC for 10 hours. This means a battery pack should be charged with at least

5 amp hours capacity.

PARTS REPLACEMENT

One part is user replaceable. The quartz halogen bulb is proprietary and is

available through Vector. A substitute 6 volt H3 55 watt bulb may be used in place

of a existing bulb. These can be purchased from popular automotive parts suppliers

nationwide. For replacement parts and any additional information you may need,

contact Technical Support at (800) 618-5178.

Spotlight Bulb Replacement

To replace the H3 type 6 volt bulb you will need a small Phillips type screwdriver and

a replacement bulb (Vector Part VEC193). Bulb life may be shortened by installing a

bulb with dirt or fingerprints on it. The bulb can be wiped clean with a cloth

moistened with alcohol. During bulb installation, avoid touching the glass part of the

bulb (see Figures 2A and 2B for details).

1. Disconnect the unit from any charging adapters.

2. Push the rubber bezel forward toward the front of the spotlight to reveal two small

Phillips screws in the retaining ring.

3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.

4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside.

5. Carefully remove the reflector and bulb assembly (see Figures 2A and 2B).

6. Disconnect the bulb wire from the red power wire.

7. Unsnap the hairpin retaining wires from the reflector’s flange.

Figure 1

RETAINING RING RUBBER

“O” RING

REFLECTOR

RUBBER

END CAP

RUBBER GUARD COVER

TRIGGER LOCK

TRIGGER

SWITCH

QUARTZ HALOGEN

BULB

BATTERY CHARGE

LEVEL INDICATOR

VEC156BD_Manual_022305 4/11/05 6:02 PM Page 4

SPECIFICATIONS

Spotlight Bulb: 6 volt, H3 series, 55 watt

Battery: Maintenance-free, sealed lead acid,

6 volt, 3 amp hour

AC Charger: UL Listed Class 2, 12 volt DC (300 mA)

DC Plug Fuse: 0.5A/250 V

Weight: 2.8 lbs. (1.5Kg)

Length: 8.25 inches

Width: 4 inches

Height: 7.75 inches

WARNINGS

Do not dispose of the battery in fire, as this may result in an explosion.

Before disposing of the battery, protect exposed terminals with

heavy-duty electrical tape to prevent shorting (shorting can result in

injury or fire).

Do not expose battery to fire or intense heat, as it may explode.

DC Plug Fuse Replacement

The fuse in the DC plug protects the charging circuit of the DC recharge adapter. If

the AC recharger operates but the DC charging adapter does not, then the fuse may

be opened.

To replace the fuse:

1. Unscrew the end cap of the DC plug (counterclockwise).

2. Remove spring center contact and fuse.

3. Check fuse with a continuity checker.

4. If blown, locate replacement fuse with same type and rating.

5. Replace the fuse, spring, contact and end cap.

6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.

7. Check for proper operation of DC charger adapter.

TROUBLESHOOTING

No red charge light

If the red LED does not turn on when charging, do the following:

A) Check for bad connection to the spotlight recharge port

B) Check for bad connection to AC or DC adapters

C) Confirm there is a functioning AC or DC current

Operating Issues

1. When charging, spotlight will not operate. Be sure spotlight charge port is

disconnected before main beam usage.

2. If trigger can’t be fully depressed, check to see if trigger switch is locked. If it

is, release the trigger lock.

3. If unit does not operate, battery may be completely discharged. Charge unit

using AC adapter following the directions in the manual.

4. If you suspect a bulb is blown, check bulb filament. If the filament is coiled and

unbroken, the bulb is not blown. If the filament is blown, replace the bulb.

VEC156BD_Manual_022305 4/11/05 6:02 PM Page 6

Altri manuali per VEC156BD

Indice

Altri manuali Black & Decker Riflettore

Black & Decker

Black & Decker 3 Manuale utente

Black & Decker

Black & Decker BSL100 Manuale utente

Black & Decker

Black & Decker 2 MILLION Power Series Manuale di istruzioni

Black & Decker

Black & Decker FPO Manuale utente

Black & Decker

Black & Decker SL331B Manuale utente

Black & Decker

Black & Decker FL3WBD Manuale utente

Black & Decker

Black & Decker SpotLiter 9360 Istruzioni per l'installazione

Black & Decker

Black & Decker 1 Manuale utente

Black & Decker

Black & Decker LIONHALBCA Manuale utente

Black & Decker

Black & Decker BSL189 Manuale utente

Black & Decker

Black & Decker 1 Manuale utente

Black & Decker

Black & Decker BDSL301 Manuale utente

Black & Decker

Black & Decker SL3AKB Manuale utente

Black & Decker

Black & Decker 3 Manuale utente

Black & Decker

Black & Decker CSL105B SPORTSPOT Manuale utente

Black & Decker

Black & Decker VEC158BD Manuale utente

Black & Decker

Black & Decker FL3WBD Manuale utente

Black & Decker

Black & Decker VEC156BD Manuale utente

Black & Decker

Black & Decker VEC156BD Manuale utente

Black & Decker

Black & Decker BDXPA0070 Manuale utente

Black & Decker

Black & Decker BDSL300 Manuale utente

Black & Decker

Black & Decker BSL301 Manuale utente

Black & Decker

Black & Decker 2 MILLION Power Series Manuale utente

Black & Decker

Black & Decker SL3WAKB Manuale utente

Manuali Riflettore popolari di altre marche

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente

LIVARNO home

LIVARNO home 375304 2101 Istruzioni originali

Cameo

Cameo CLQS40WW Manuale utente

Leviton

Leviton Ellipsoid 5/50 Manuale utente

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuale utente

Vector

Vector SL3AKV Manuale utente

Quantum

Quantum Q262 Manuale operativo

Philips

Philips Vari-lite VL3015LT Manuale utente

EUROSPOT

EUROSPOT C51 Manuale utente

DTS

DTS MINI BRICK ARC Manuale utente

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuale

ACME

ACME LED-MS350B Manuale utente

EuroLite

EuroLite Akku flat light 1 Manuale utente

Commercial Electric

Commercial Electric SPTM-1401 Manuale utente

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuale utente

Teknik

Teknik FLEXI Manuale utente

Craftsman

Craftsman CMXLSB10 Manuale utente

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuale utente