Black Box 202T Manuale utente
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
MAY 2001
MD845A-R2
Modem 202T
1
FCC AND IC RFI INFORMATION
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct
the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
2
MODEM 202T
FCC REQUIREMENTS FOR
TELEPHONE-LINE EQUIPMENT
1. The Federal Communications Commission (FCC) has established rules which
permit this device to be directly connected to the telephone network with
standardized jacks. This equipment is designed to operate only on dedicated
phone lines or wires. Do not connect to dial-up lines, coin lines, party lines, or
lines with dial tones.
2. If this device is malfunctioning, it may also be causing harm to the telephone
network; this device should be disconnected until the source of the problem
can be determined and until the repair has been made. If this is not done, the
telephone company may temporarily disconnect service.
3. If you have problems with your telephone equipment after installing this
device, disconnect this device from the line to see if it is causing the problem.
If it is, contact your supplier or an authorized agent.
4. The telephone company may make changes in its technical operations and
procedures. If any such changes affect the compatibility or use of this device,
the telephone company is required to give adequate notice of the changes.
5. If the telephone company requests information on what equipment is
connected to their lines, inform them of:
a. The telephone number that this unit is connected to.
b. The FCC registration number.
Item (b) can be found on the unit’s FCC label.
6. In the event of an equipment malfunction, all repairs should be performed by
your supplier or an authorized agent. It is the responsibility of users requiring
service to report the need for service to the supplier or to an authorized
agent.
3
CERTIFICATION NOTICE FOR EQUIPMENT USED IN CANADA
CERTIFICATION NOTICE FOR
EQUIPMENT USED IN CANADA
The Industry Canada label identifies certified equipment. This certification means
that the equipment meets certain telecommunications-network protective,
operation, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In
some cases, the company’s inside wiring associated with a single-line individual
service may be extended by means of a certified connector assembly (extension
cord). The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized maintenance
facility—in this case, Black Box. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
CAUTION:
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
4
MODEM 202T
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los orificios de
ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el aparato.
5
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
6
MODEM 202T
TRADEMARKS USED IN THIS MANUAL
Any trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
7
CONTENTS
Contents
Chapter Page
1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. Modem Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Full Duplex 4-Wire Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Half-Duplex 2-Wire Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3 Half-Duplex 4-Wire Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.4 Simplex or Bits Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.5 Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. Making Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 Connections Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3 RS-232 Serial Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4 Operating Mode Selection and Wiring . . . . . . . . . . . . . . . . . . . . . . . 15
5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Component Locator Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Baud Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Character Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.4 Handshake Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.5 Self-Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appendix. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
A.1 Calling Black Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
A.2 Shipping and Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8
MODEM 202T
1. Specifications
Range: Up to 20 miles on unloaded lines, depending upon line characteristics.
Unlimited on loaded lines.
Operating Frequency: 1200/2200 Hz (Bell 202 or 1300/2100 CCITT V.35) FSK
(Frequency Shift Key)
Data Rates: 300, 600, or 1200 baud half- or full duplex up to 1200 baud simplex
Handshake Modes: DataSense (DSCC) or RTS line
Enclosure: Standard NEMA 1; 18-gauge steel with mounting flanges
Temperature Tolerance: -4 to +158°F (-20 to +70°C)
Indicators: (4) LEDs: Data Out, Data In, Carrier, Power
Connectors: (2) terminal blocks, (1) DB9 female
Power required: Input: 11 to 18 volts DC at a minimum of 200 ma. External
wallmount power supply provided for 110 VAC nominal.
Size: 1.5"H x 5"W x 9"D (3.8 x 12.7 x 22.9 cm) over mounting flanges
Mounting: Hole pattern 1⁄4inch diameter located on rectangle 8.3 by 2.8 inches
9
CHAPTER 2: Introduction
2. Introduction
The Modem 202T is a Bell 202 (CCITT V.23 optional) voice-band, 1200-baud
modem. Use it on private, leased, un-switched telephone lines or any dedicated 2-
or 4-conductor wire (twisted or untwisted, shielded or unshielded). The Modem
has a range of up to 20 miles (32.2 km) on any ordinary wire pairs or unlimited on
“loaded” telephone company voice-grade (VG-6) leased lines.
The Modem 202T can operate without handshake lines using the proprietary
DataSense (DSCC) microprocessor firmware. This feature detects and buffers
incoming RS-232 data to allow the assertion and stabilization of the FSK carrier
before transmitting the buffered characters.
The nominal operating supply voltage for the Modem 202T is 12 VDC via a
2-conductor screw terminal power connector.
Altri manuali per 202T
1
Indice
Altri manuali Black Box Modem
Black Box
Black Box SHM-768K Series Manuale utente
Black Box
Black Box Tote-a-Fax 542 Manuale utente
Black Box
Black Box ME760A-R2 Manuale utente
Black Box
Black Box ME0005A-10BT Manuale utente
Black Box
Black Box MT240A-R2 Manuale utente
Black Box
Black Box ME0002A-V35 Manuale utente
Black Box
Black Box ME260A Manuale utente
Black Box
Black Box Sync/Async Fiber Optic Modem Manuale utente
Black Box
Black Box SHM-B Sync Manuale utente
Black Box
Black Box ME109A Manuale utente
Black Box
Black Box SHM-NPR Series Manuale utente
Black Box
Black Box ME605A-FST Manuale utente
Black Box
Black Box ME570A-MST-R2 Manuale utente
Black Box
Black Box MAY 1994 Manuale utente
Black Box
Black Box MD1970A Manuale utente
Black Box
Black Box ME801A Manuale utente
Black Box
Black Box Mini-Modem V.92 MD1626A Manuale utente
Black Box
Black Box MC119A Manuale utente
Black Box
Black Box MD1620A Manuale utente
Black Box
Black Box TL304A Manuale utente
