Black Horse Model Impulse 100TD Manuale utente
SPECIFICATION
Instruction Manual book
Wingspan : 1,750 mm 68.90 in.
Length :
Weight : 4,4 kg 9.68 Lbs.
Radio : 07 channels.
Servo : 08 servos.
1,285mm 50.59in.
Engine : 55 - 2 Stroke
15 -20CC Gas.
ElectricMotor: RIMFIRE.80
Battery:5-6Cells-Li-Poly18.5-22.2V-5.500mAh.
Propeller: 15X 6
Speed control: 60A.
ITEMCODE:BH121.
Madein Vietnam.
2
Impulse 100TD - Item code: BH 121 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybefore startingassemblyof your Impulse 100TD.Usethe partslistingbelow to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesigned to helpthenewpilotonhiswaytosuccessful R/C flight. Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landing gear.....
Toavoidscratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand to protectthe table. Keepa couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrial fit all theparts.Makesureyouhave
the correct parts and that they fit and are
alignedproperlybeforegluing!Thiswill assure
properassembly.Impulse 100TDARFis hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderand acetone.Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.
3
Impulse 100TD - Item code: BH 121 . Instruction Manual
Caution: this model is not a toy!
If you are a beginner to this type of powered
model,pleaseaskan experienced model flyer
forhelp and support.If you attemptto operate
themodelwithoutknowingwhatyouaredoing
you could easily injure yourself or somebody
else. Please keep your safety and well-being
in mind at all times.
Important: before you start construction
Evenif you have already built a large number
ofRC models pleaseread right through these
instructions and check all the kit components
against the parts list. We have taken great
trouble to keep construction as simple as
possible, without making any compromises
in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the
film covering due to major fluctuations in
weather conditions (temperature, humidity
etc.); in rare cases you may even find a slight
warp in a component. These minor faults are
in the nature of film-covered built-up wooden
structures, and can easily be corrected using
a heat gun, as commonly used for modelling.
Creases: Blowwarmairoverthearea
and rub down with a soft
cloth.
When self-tapping screws have to be
screwed into wood, apply a little white
glue to prevent them shaking loose: just
squirt white glue into the hole and fit the
screw.
+ This is not a toy
+ Be sure that no other flyers are using your
radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from
children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely at-
tached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
thepropeller.
+ Do not start the engine if people are near.
Do not stand in line with the side of the pro-
peller.
+ Make engine adjustments from behind the
propeller only. Do not reach around the spin-
ningpropeller.
SAFETY PRECAUTION.
Wing warp: Hold the panel twisted
gently in the opposite
direction to the warp, and
apply warm air to remove
the creases from the
covering.
Caution! do not heat the film more than is
absolutely necessary. If the air or the iron is
too hot, the film may melt and holes may be
formed.
This model is highly pre-fabricated and can
bebuilt in a very short time. However,thework
which you have to carry out is important and
must be done carefully. The model will only
be strong and fly well if you complete your
tasks competently - so please work slowly
and accurately.
REPLACEMENT LARGE PARTS
A.
B1.
E.
D2. G.
C.
B2.
D1.
F.
A.Cowling.
B. Wing panel(B1,B2).
C. Fuselage.
D. Horizontal stabilizer.
E.Rudder.
F. Aluminium wing dihedral brace.
G. Decal sheet .
4
Impulse 100TD - Item code: BH 121 . Instruction Manual
REPLACEMENT SMALL PARTS
1. Install the rubber grommets and brass
eyelets onto the aileron servo.
7. Wheels.
2. Wheel pants.
3. Fuel Tank.
5. Tail gear set.
8.Spinner.
9. Plastic parts for elevator and rudder pushrod.
1. Aluminium landing gear.(Right & Left).
6. Plastic parts for landing gear.
4. Engine mount ply of wood .
1.INSTALLING THE AILERON SERVO.
I. SERVO
Temporary pin to
keep hinge centered.
Cutthe covering
awayfromtheslot.
a.
b.
Bottom side
Aileron
5
Impulse 100TD - Item code: BH 121 . Instruction Manual
2.Using a modelingknife,remove the cov-
ering servo tray.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
Servo tray.
Removecovering
3. Drill 1,5mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo. Install servo into ai-
leron servo tray as same as picture below.
4. Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
Secure.
Thread.
Electric
wire.
6
Impulse 100TD - Item code: BH 121 . Instruction Manual
Repeat the procedure for the other wing
half.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
2. INSTALLING THE AILERON CONTROLHORN.
Secure.
Aileroncontrol horn
Installaileroncontrol hornassame
aspicturebelow.
Repeat the procedure for the other wing
half.
Installing the aileron linkages as pictures
below.
Attach the clevis to the outer hole in the con-
trol horn.
A+B Epoxy
PLUS
Control horn
of the aileron
60mm
M2.
3.INSTALLING THE AILERON
LINKAGES .
7
Impulse 100TD - Item code: BH 121 . Instruction Manual
Electric
wire
2x10mm.
Secure.
Control horn of the flap
A+B Epoxy
PLUS
2. INSTALLING THE FLAPCONTROLHORN.
II. FLAP
1. INSTALLING THE FLAP SERVO .
Thread
8
Impulse 100TD - Item code: BH 121 . Instruction Manual
Repeat the procedure for the other wing
half.
THERE ARE TWO OPTIONS:
1. ELECTRIC MOTOR
2. ENGINE MOUNT.
1. OPTION 1: ELECTRIC MOTOR
INSTALLING ELECTRIC MOTOR.
Installing the aileron linkages as pictures
below.
3.INSTALLING THE FLAP
LINKAGES.
60 mm
M2.
Control horn
of the flap
3x 15mm
Bottom side
Flap Aileron
9
Impulse 100TD - Item code: BH 121 . Instruction Manual
Remove
Wood.
3x 15mm
Secure.
Drill a hole 2mm diameter.
C/Aglue.
10
Impulse 100TD - Item code: BH 121 . Instruction Manual
See pictures below:
2. OPTION 2: ENGINE MOUNT
5x 80mm
Secure. Right side
Frontview.
Rotor sharft.
Motor.
Left side.
Battery.
3 x 15mm
Frontview.
INSTALLING THE ENGINE MOUNT.
Altri manuali per Impulse 100TD
1
Indice
Altri manuali Black Horse Model Giocattolo
Black Horse Model
Black Horse Model T-28 Trojan 120 Manuale del proprietario
Black Horse Model
Black Horse Model BH58 Manuale del proprietario
Black Horse Model
Black Horse Model VIPER JET TURBINE Manuale del proprietario
Black Horse Model
Black Horse Model Spitfire-EP Manuale del proprietario
Black Horse Model
Black Horse Model Edge 540-V3 Manuale del proprietario
Black Horse Model
Black Horse Model JU87-STUKA Manuale del proprietario
Black Horse Model
Black Horse Model Edge 540-V3 Manuale del proprietario
Black Horse Model
Black Horse Model YAK 11 Manuale del proprietario
Black Horse Model
Black Horse Model Spitfire 40 Manuale utente
Black Horse Model
Black Horse Model BH175 Manuale utente
Black Horse Model
Black Horse Model Edge 540-V3 Manuale del proprietario
Black Horse Model
Black Horse Model Thermal 3.0 Manuale utente
Black Horse Model
Black Horse Model TAYLORCRAFT BH 134 Manuale utente
Black Horse Model
Black Horse Model FAIRCHILD 24W Manuale del proprietario
Black Horse Model
Black Horse Model Travel Air BH.06 Manuale del proprietario
Black Horse Model
Black Horse Model GLASAIR Manuale del proprietario
Black Horse Model
Black Horse Model OV-1 MOHAWK Manuale del proprietario
Black Horse Model
Black Horse Model SEA FURY BH148 Manuale del proprietario
Black Horse Model
Black Horse Model EAGLE Manuale del proprietario
Black Horse Model
Black Horse Model BH180 Manuale del proprietario
