Black Opal RMU10HX Manuale

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW i

Specifications & Set-up

READ THIS DOCUMENT THOROUGHLY BEFORE

ATTEMPTING TO ASSEMBLE OR OPERATE

THE

Black Opal

Multi Function Flat Panel Display System

Model RMU10HX

Treatment of this product other than as specified herein may result in:

damage to the product or attached systems;

invalidation of the warranty.

The location of this document should always be known to all users of, and technical

support personnel for, the Black Opal RMU.

The information contained herein is proprietary to Laserdyne Pty Ltd. No part of this work may be

reproduced or copied in any way without prior written permission of Laserdyne Pty Ltd.

Note: specifications herein are subject to change without notice.

CAUTIONS:

•User-supplied cables must be correctly wired (see Connector/Pin

Details).

•Ensure that external power is within the range specified.

•Ensure that external power is off before proceeding with set-up.

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW ii

Tracking Records

This document is appropriate for the following product

configurations:

Model: Black Opal Model:

RMU10HX.

Initial Installed Software Version: 4.5

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW iii

TABLE OF CONTENTS

Chapter Page

1 SYSTEM SPECIFICATIONS 1-1

1.1 System Performance 1-1

1.2 Controls 1-2

1.3 Communications 1-3

1.4 Physical Characteristics 1-3

1.5 Electrical Requirements 1-3

1.6 Environmental 1-4

1.7 Connector/Pin Details 1-4

2 SET-UP 2-1

2.1 Mounts 2-1

2.2 Connections 2-1

2.3 Set-up Procedure 2-2

2.4 Heating and Cooling 2-3

LIST OF FIGURES

Figure 2-1: Mounts 2-1

Figure 2-2: Connections 2-2

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-1

1SYSTEM SPECIFICATIONS

1.1 System Performance

PARAMETER SPECIFICATION

Designation

RMU10HX Remote Monitor Unit, 10”, High

brightness, XGA

Control

Control Functions [factory configurable to

customer requirements]

power On/Off; backlight intensity;

menu select; select screen lay-out;

select image enhancement feature;

digital zoom; freeze frame

Controls tactile 8-button membrane

Display

Type Active Matrix Colour (18-bit colour)

LCD Module

Display Size (″{cm}) diagonal 10.4 {26.42}

active area 8.31 {21.1} x 6.24 {15.8}

Aspect Ratio [width:height] 4:3

Pixel Number [1 pixel is RGB trio] 1,024 x 768

Colour 262k [6-bit each colour]

Grey Scale 256 [8-bit]

Backlight Luminance [CCFT type; minimum

approx.; adjustable] (cdm-2) 1maximum 1,700

Contrast Ratio [limiting; LCD] 300:1

Response Time [max.] (ms) 50

Readability [ambient conditions] black-out to full direct sunlight

[105lux]

Night Vision Device compatible? yes [low intensity green]

Viewing Angle vertical +40/-35

[full angle] (°)horizontal ±55

Inputs

Inputs 2 video and 1 PC [4 and 1 optional]

Signal Formats video PAL [all forms], NTSC [all forms],

SECAM [all forms], CCIR-601, RS170;

interlaced and non-interlaced

PC non-interlaced, 60Hz, RGB, separate

Hsync. & Vsync., up to 1,024 x768

[standard PC XGA]

11 cdm-2= 1 nit.

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-2

1.1 System Performance (cont’d)

PARAMETER SPECIFICATION

Inputs (cont’d)

Connection Formats video Composite, S-Video [Y-C]

PC RGB + Hsync. + Vsync.

Outputs

Video prime video input is output [what

comes in goes out]

Safety & Protection

Cooling thermal transfer by internal and

external convection; cooling fin fitted to

rear

Backfill purged & backfilled [N2]

Display Window Antireflection, hard-coated, sealed,

EMI/EMC shielded

Altitude/Decompression pressure relief valve, 2-way

Electrical Protection conforms to QSTAG 307

Audible Emission [@ ≥10m] nil

Support

MTBF (hours) > 8,000

Operational Life (years) 10

1.2 Controls

Control Type Location Primary Label Primary Function

Button membrane

on left of

top toggle between active

and standby

Button front face 2nd top 1menu

Button 3rd top 2show assigned screen

lay-outs for selection

Button middle 3enhance

Button 3rd bottom 4zoom

Button 2nd bottom 5freeze

Button bottom left -backlight down;

scroll/adjust down

Button bottom right +backlight up;

scroll/adjust up

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-3

1.3 Communications

PARAMETER SPECIFICATION

Ports one Serial port 2

Data Format RS232 [RS422 optional]

Rate (Baud) 9,600 [1,200 to 230.6k optional; or to

10 Mbaud for RS422]

1.4 Physical Characteristics

PARAMETER SPECIFICATION

Mass [approx.] (kg) 4.7

Dimensions Width body 281

(mm) overall 3307

Height body 211

overall 3229

Depth 496

Specific Gravity >1 [non-floatation]

Mounting 5Dzus fasteners x 6[type PFSC35] or

or 2-way adjustable mounting bracket

optional

1.5 Electrical Requirements

PARAMETER SPECIFICATION

Supply Voltage (Vdc) 20 to 33 [28 nominal]

Current Drain heater on < 3

[@ 28Vdc; typical] (A) heater off < 2

2Shared with power input.

3Including mounting flange.

4Excluding connectors.

5Optional 2-way adjustable mounting bracket has four ¼” clearance holes for mounting

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-4

1.6 Environmental

PARAMETER SPECIFICATION

Temperature (°C) Operate 6min. -25 [without wind-chill]

max. +55 [without solar radiation]

Survive min. -30 [without wind-chill]

max. +71 [without solar radiation]

Vibration and Shock MIL-STD-810E, aircraft 7

Sealing 8water resistant [drip & spray]

EMI/EMC 8MIL-STD-461D 7

1.7 Connector/Pin Details

No. Name Pin

Marking

Purpose Notes for

Harness

Comment

A: VGA Input: Connector, MilSpec, Mil-C26482, Panel, Plug, Bayonet, 19 Way, 14 Shell, Pattern 105,

square flange, AB05 2100 14-19P N00

A1 RED OUT AN/A

A2 RED IN BRED INPUT coax (B,P), 75Ω

DB15 pin 1. Also Pr

input for component

video

A3 GREEN OUT CN/A

A4 GREEN IN DGREEN INPUT coax (D,R), 75Ω

DB15 pin 2. Also Y

(and SOG) input for

component video

A5 BLUE OUT EN/A

A6 BLUE IN FBLUE INPUT coax (F,S), 75Ω

DB15 pin 3. Also Pb

input for component

video

A7 HS OUT GN/A

A8 HS IN HHSYNC INPUT signal wire DB15 pin 13

A9 VS OUT JN/A

A10 VS IN KVSYNC INPUT signal wire DB15 pin 14

A11 DDC_5V LDDC CHANNEL +5V unused DB15 pin 9

A12 DDC_SDA MDDC CHANNEL DATA unused DB15 pin 12

A13 DDC_SCL NDDC CHANNEL CLOCK

unused DB15 pin 15

6When used in accordance with procedures in User’s Manual.

7Contact supplier for details.

8With compliant line connectors attached.

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-5

1.7 Connector/Pin Details (cont’d)

No. Name Pin

Marking

Purpose Notes for

Harness

Comment

A: VGA Input (cont’d)

A14 RED GND PRED coax GND coax braid DB15 pin 6

A15 GREEN GND RGREEN coax GND coax braid DB15 pin 7

A16 BLUE GND SBLUE coax GND coax braid DB15 pin 8

A17 DIGITAL GND THSYNC GND signal wire DB15 pin 5

A18 DIGITAL GND UVSYNC GND signal wire DB15 pin 10

A19 N/C VUNUSED unused DB15 pin 4,11

B: Video Input: Connector, MilSpec, Mil-C26482, Panel, Socket, Bayonet, 19 Way, 14 Shell, Pattern

105, square flange, AB05 2100 14-19S N00

B1 Y1_GND APrimary video

(composite or luma)

GND

coax, 75Ω

shield

B2 Y1_SIGNAL BPrimary video

(composite or luma)

input

coax, 75Ω

center

75Ωterminated in

display

B3 Y2_GND CSecondary video

(composite or Y) GND

coax, 75Ω

shield

B4 Y2_SIGNAL DSecondary video

(composite or Y) input

coax, 75Ω

center

75Ωterminated in

display

B5 RS485+ ERS485+ connection signal

B6 RS485-FRS485-connection signal

B7 V-Gdc-(GND) connection 5A dc internally isolated

from comms and

video GND.

B8 V+ HOutput power (+28V) 5A dc Same as input dc

B9 V+ JOutput power (+28V) 5A dc Same as input dc

B10 VIDEO_OUT KSwitched video output coax, 75Ω

center

either Y1 or Y2

output, 75Ωdouble

terminated

B11 GND_OUT LVideo output GND coax, 75Ω

shield

B12 SPARE1 MAnalogue input signal SPARE1

B13 SPARE2 NAnalogue input signal SPARE2

B14 C1_SIGNAL PPrimary chroma input

[or VCR composite

input]

coax, 75Ω

center

75Ωterminated in

display

B15 C2_SIGNAL RSecondary chroma

input

coax, 75Ω

center

75Ωterminated in

display

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 1-6

1.7 Connector/Pin Details (cont’d)

No. Name Pin

Marking

Purpose Notes for

Harness

Comment

B: Video Input (cont’d)

B16 C_GND SChroma common [or

VCR composite input]

coax, 75Ω

shield

B17 V-Tdc-(GND) connection 5A dc internally isolated

from comms and

video GND.

B18 RS232_TX URS232 transmit

(output from display)

signal

B19 RS232_RXVRS232 receive (input

to display)

signal

C: dc Power Input & Comms Port Connection: Connector, MilSpec, Mil-C26482, Panel, Plug, Bayonet,

12 Way, 14 Shell, Pattern 105, square flange, AB05 2100 14-12P N00

C1 COMMS_GND Acommon for comms signal

C2 N/C Bunused

C3 RS232_RX CRS232 receive (input

to display)

signal

C4 RS232_TX DRS232 transmit

(output from display)

signal

C5 nRESET Eactive low display

reset control

reserved

C6 MODAB Factive low display

bootload control

reserved

C7 RS485-GRS485-connection reserved

C8 RS485+ HRS485+ connection reserved

C9 V-Jdc-(GND) connection 5A dc internally isolated

from comms and

video GND.

C10 V-Kdc-(GND) connection 5A dc internally isolated

from comms and

video GND.

C11 V+ LInput power (+28V)

for display

5A dc +20..+33V input

C12 V+ MInput power (+28V)

for display

5A dc +20..+33V input

Specifications & Set-up:

Black Opal Model RMU10HX

Flat Panel Display System

PS-RMU-M-0269-0_1 6.7.06 TW/TW 2-1

2SET-UP

2.1 Mounts

The RMU has two optional mounting methods:

six type PFSC35 Dzus fasteners, located on the left and right (three per

side) of the mounting flange; or

a 2-way adjustable mounting bracket fitted to the RMU.

In the case of the 2-way adjustable mounting bracket, four mounting points are

provided, being ¼” diameter clearance holes located in the top section of the

bracket.

Figure 2-1: Mounts

2.2 Connections

The RMU has three connection points located on the rear of the unit:

Connector A, the VGA Input connector;

Connector B, the Video Input connector; and

Connector C, the dc Power Input & Comms Port connector.

mounting

points

Indice

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione