BLAUBERG CEILEO 110 Manuale utente
CENTRIFUGAL CEILING FAN
CEILEO 110/130/150
CEILEO 110/130/150 T/TH/TP
CEILEO 110/130/150 LIGHT
CEILEO 110/130/150 LIGHT T/TH/TP
CEILEO 110 DC T/TH/TP
CEILEO 110 DC LIGHT T/TH/TP
CEILEO 150 DC T/TH/TP
CEILEO 150 DC LIGHT T/TH/TP
INSTALLATION GUIDE
INSTALLATION
Tools required
Pencil Drill Screwdriver Dowel 4 pcs Screws 4 pcs
The fan is a component part and is not designed for stand-alone operation.
The fan is constructed for ceiling installation in the floor slab and fixation to the inter joist with the distance between the ceiling joists from 270 mm (10 5/8”) up to
680 mm (20 3/4”) using the removable fixing brackets or the fastening holes in the fan casing.
The installation place must be in compliance with local construction norms for units of this type.
Check the fan for mechanical damages prior to mounting .
Make sure that the casing comprises no foreign objects, such as paper or foil.
While mounting the fan sufficient service access for maintenance or repair operations must be provided.
The minimum gap between the fan and the ceiling is 5 mm (3/16”).
L = min 5 mm L = min 5 mm(3/16") (3/16")
www.blauberg.us MIU_76_77-01
174 N. 36th Street, Lafayette, IN 47905
e-mail: [email protected]
MOUNTING STEPS
1. Attach the fan to the interjoist using the screws. 2. Connect the air duct of a required diameter.
3. Connect the LED lamps (included in the delivery set) for the Light models.
Option: connect the humidity sensor or the motion sensor (specially ordered accessory).
For the Light models: connect the power socket of the LED lamp and the respective sockets in the terminal box.
For theTH models with a humidity sensor: remove the protective cap from the grille prior to its installation.
Route the contact socket of the sensorTH or TP via the opening in the grille and connect the sensor socket to the respective contact socket on the control unit.
Fix the sensor in the grille opening and cover the opening with a protective cap.
Connection socket
of the humidity sensor
Connection socket
of the motion sensor
Connection socket
of the LED lamp
Connection socket
of the humidity sensor
Connection socket
of the motion sensor
4. Install the decorative grille on the fan casing using the holders on the casing.
www.blauberg.us MIU_76_77-01
174 N. 36th Street, Lafayette, IN 47905
e-mail: [email protected]
Side xation
to one of the ceiling joists
Installation
between the ceiling joists
Fixation between
the ceiling joists using the mounting brackets
Additional fastening holes in the fan casing may be used for mounting purposes
BASIC FAN INSTALLATION OPTIONS
www.blauberg.us MIU_76_77-01
174 N. 36th Street, Lafayette, IN 47905
e-mail: [email protected]
CONNECTION TO POWER MAINS
DISCONNECTTHE UNIT FROM POWER MAINS PRIOR TO ANY OPERATIONS.
THE UNIT MUST BE CONNECTEDTO POWER MAINS BY A QUALIFIED ELECTRICIAN.
THE RATED ELECTRICAL PARAMETERS OFTHE UNIT ARE SHOWN ONTHE RATING PLATE.
ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED AND WILL VOID
THE WARRANTY.
The fan is rated for connection to single-phase AC 120 V/ 50/ (60) Hz power supply.
The fan must be connected to power mains using durable, insulated and heat-resistant conductors (cables and wires) via the circuit
breaker QF integrated into the house cabling system.
The external circuit breaker installation place must ensure unhampered access for emergency shutdown of the unit
WIRING DIAGRAMS
L2
L1
N
L
N
LT
N
L
N
L
QF
LIGHT
(contact socket is available only for
the models with LED light)
FAN
Х1QF
1234567
120 V
60 Hz
120 V
60 Hz
ACCESS TO THE TERMINAL BOX FOR WIRING THE FAN
Remove the decorative grille.
For accessing the connection terminals
loosen the screw on the terminal box
lid and take the lid o.
Remove the protective cap and install the cable gland.
www.blauberg.us MIU_76_77-01
174 N. 36th Street, Lafayette, IN 47905
e-mail: [email protected]
Questo manuale è adatto per i seguenti modelli
35
Altri manuali BLAUBERG Ventilazione
