Blizzard Lighting ThunderStik Manuale utente
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2016
Thunder/tik
Page 2
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
TABLE OF CONTENTS
ThunderStik™ LED Fixture 1
1. Getting Started 3
What’s In The Box? 3
Optional Accessories (sold separately) 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The ThunderStik™ 5
Main Features 5
Additional Features 5
DMX Quick Reference 5
The ThunderStik™ Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of ThunderStik™ Fixtures 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
4. Operating Adjustments 10
The Control Panel 10
Control Panel Menu Structure 11
DMX Mode 12
Select The Channel Mode 12
Select The DMX Starting Address 12
Slave Mode 12
Auto, Stand-Alone, Sound Active Modes 12
Auto Mode 12
Sound Active Mode 12
Manual Adjustments 12
DMX Channel Values In-Depth 13
Troubleshooting 14
5. Appendix 15
A Quick DMX Lesson 15
Keeping Your ThunderStik™ As Good As New 16
Returns (Gasp!) 16
Shipping Issues 16
Tech Specs 17
Dimensional Drawings 18
Page 3
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x ThunderStik™ Fixture
• An Ever-So-Handy Power Cord
• A Sweet Safety Cable & 2 Mounting Brackets
• One Really Classy DMX Cable
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on purchasing the mighty ThunderStik™, your new #1 weapon to help win
the war on darkness! Now that you’ve got your ThunderStik™ (or hopefully, Stiks!), you
should carefully unpack the box and check the contents to ensure that all parts are present
and in good condition. If anything looks as if it has been damaged in transit, notify the
shipper immediately and keep the packing material for inspection. Again, please save the
carton and all packing materials. If a xture must be returned to the factory, it is important
that the xture be returned in the original factory box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the
xture you receive is suitable for your local power supply. See the label on the xture or
refer to the xture’s specications chart for more information. A xture’s listed current
rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied does
not match the voltage indicated on the voltage selector switch. All xtures must
be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something happens goes wrong, please visit www.blizzardlighting.com/
support and open a support ticket. We’ll be happy to help, honest.
Blizzard Lighting
N24 W23750 Watertown Rd. Suite B
Waukesha, WI 53188 USA
www.blizzardlighting.com
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any
errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the
right to update the existing document or to create a new document to correct any errors
or omissions at any time. You can download the latest version of this document from www.
blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 3/3/2016 J. Thomas 3/6/2016
Page 4
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de-
cal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at www.
blizzardlighting.com/support.
Page 5
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
2. MEET THE THUNDERSTIK™ LED FIXTURE
MAIN FEATURES
• 5* 15W high output RGBW Quad-Color OSRAM™ LEDs
• Moving head with fast & quiet 250º tilt via 3-phase motors
• Sharp multicolor moving beam effects
• Narrow 5º beam angle
• Smooth 0–100% linear dimmer
• Built-in color macros via DMX
• Built-in automated programs via master/slave
• Built-in sound active programs
• Removable light diffusion panel
• RGBW color mixing ability in standalone mode
• DMX-512, Auto, Sound Active, & Master-Slave
• PowerCon™ compatible AC power In/Out connectors
CONTROL:
• USITT DMX-512 (12/32 Channels)
• 3/5-pin DMX Input/Output
• 4-button control panel menu with LCD display
DMX Quick Reference (12/32-Channel Modes)
Channel Reduced Mode Channel Standard Mode
1 Dimmer 1 Dimmer
2 Shutter/Strobe 2 Shutter/Strobe
3 Tilt 3 Tilt
4 Tilt Speed 4 Tilt Speed
5 Color Macros 5 Macro Effects
6 Red Intensity 6 Red Intensity
7 Green Intensity 7 Green Intensity
8 Blue Intensity 8 Blue Intensity
9 White Intensity 9 White Intensity
10 Pattern 10 Pattern
11 Scanner Effect 11 Scanner Effect
12 Background Color 12 Background Color
-- -- 13 Red 1 Intensity
-- -- 14 Green 1 Intensity
-- -- 15 Blue 1 Intensity
-- -- 16 White 1 Intensity
-- -- 17-28 R/G/B/W LEDs 2-4
-- -- 29 Red 5 Intensity
-- -- 30 Green 5 Intensity
-- -- 31 Blue 5 Intensity
-- -- 32 White 5 Intensity
Page 6
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
Figure 1: The ThunderStik™ Pin-Up Picture
5* 15W High Output RGBW Quad-
Color OSRAM™ LEDs
Figure 2: The Rear Connections
LCD Control
Panel Display
Power
In
DMX
In
Fuse
Holder
4* Control
Panel Menu
Buttons
DMX
Out
Power
Out
Page 7
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
With a at head screwdriver, remove the fuse holder out of its hous-
ing. Remove the damaged fuse from the holder and replace with exact
same type fuse. Insert the fuse holder back in its place and reconnect
power.
Connecting A Bunch of ThunderStik™ Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the xtures on a serial data link determines the number of x-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal. The maximum recommended cable-run dis-
tance is 500 meters (1640 ft). The maximum recommended number of
xtures on a serial data link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Page 8
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3-pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of the
DMX cable to the rst xture’s male connec-
tor (input). Note: It doesn’t matter which
xture address is the rst one connected.
We recommend connecting the xtures in
terms of their proximity to the controller,
rather than connecting the lowest xture
number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.
Page 9
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3/5-pin connector side of the
DMX cable to the output (female) 3/5-pin connector
of the rst xture.
2. Connect the end of the cable coming from the
rst xture which will have a (female) 3/5-pin con-
nector to the input connector of the next xture
consisting of a (male) 3/5-pin connector. Then, pro-
ceed to connect from the output as stated above to
the input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also re-
quire a slave setting.
Check the “Operating Adjustments” section in this manual for com-
plete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xutres overhead.
Adjust the angle of the xture by loosening both knobs and tilting the
xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
Page 10
Thunderstik™ User Manual Rev. A © 2016 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and different modes possible with the ThunderStik™ are
accessed by using the control panel on the front of the xture. There are 4
control buttons to the right of the LCD display which allow you to navigate
through the various control panel menus.
<MENU>
Is used to navigate to the previous higher-level menu item.
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
<ENTER>
Is used to select and conrm/store the current selection.
The control panel LCD display shows the menu items you select from the menu
map on page #11. When a menu function is selected, the display will show
immediately the rst available option for the selected menu function.
Use the <UP/DOWN> buttons to navigate the main menu options. Press the
<ENTER> button to select any menu function currently displayed, then use
the <UP/DOWN> buttons to scroll through any submenu options. You can the
press <ENTER> to save any changes made, or press the <MENU> button to
exit without saving.
MENU
UP
DOWN
ENTER
DMX ADDR:
< Stan Mod >
SING
SOUN
AUTO
Indice
Altri manuali Blizzard Lighting Attrezzatura per DJ
Blizzard Lighting
Blizzard Lighting Puck CSI Xtreme Manuale utente
Blizzard Lighting
Blizzard Lighting Torrent FZ Manuale utente
Blizzard Lighting
Blizzard Lighting Kaptivator Manuale utente
Blizzard Lighting
Blizzard Lighting Solar Ray Manuale utente
Blizzard Lighting
Blizzard Lighting Redstone 240Z Wash Manuale utente
Blizzard Lighting
Blizzard Lighting Weather System EXA Manuale utente
Blizzard Lighting
Blizzard Lighting Laser Blade G Manuale utente
Blizzard Lighting
Blizzard Lighting Shoqwave X6 Manuale utente
Blizzard Lighting
Blizzard Lighting Blockhead Z9 Manuale utente
Blizzard Lighting
Blizzard Lighting Motif Fresco Series Manuale utente
Blizzard Lighting
Blizzard Lighting Laser Blade G Manuale utente
Blizzard Lighting
Blizzard Lighting PROPAR COB RGBAW Manuale utente
Blizzard Lighting
Blizzard Lighting ENIGMA M4 Manuale utente
Blizzard Lighting
Blizzard Lighting Stiletto Glo 19 Manuale utente
Blizzard Lighting
Blizzard Lighting TOUGHPAR ZOOM RGBAW Manuale utente
Blizzard Lighting
Blizzard Lighting StormChaser Skywire RGBAW Manuale utente
Blizzard Lighting
Blizzard Lighting LB Bar CSI Manuale utente
Blizzard Lighting
Blizzard Lighting ToughSTICK RGBAW Manuale utente
Blizzard Lighting
Blizzard Lighting VERISMO RGBALC Manuale utente
Blizzard Lighting
Blizzard Lighting LB HEX Manuale utente
