Blu-Comm Bluetooth Adaptors Manuale utente

Blu-Comm™ Bluetooth® Adaptors User Guide

For Motorola and Kenwood portable radios

The Blu-Comm™ Adaptor allows you to use a compatible wireless headset or

other audio accessory with your two-way radio.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged

to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to

operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC

RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.

Controls and Connection

Quick Disconnect Accessory Port

Allows the connection of a QD series

wired audio accessory, such as a

Push-to-Talk, earphone, or

auxiliary microphone.

Radio Connector

This port connects the Blu-Comm

Adaptor to a compatible two-way

radio.

Multi-Function Talk Switch / Status LED

Used to place the Blu-Comm Adaptor in pairing

mode. The LED ﬂashes messages that let the user know

the current status of the Blu-Comm Adaptor. Once

paired with an audio accessory, this switch is used to

activate the Push-To-Talk function of the two-way radio.

QUICK START

1. Connect the Blu-Comm Adaptor to a compatible two-way radio.

2. Pair the Blu-Comm Adaptor with a compatible wireless audio accessory.

3. Connect a wired audio or PTT accessory to the Quick-Disconnect accessory port on the

Blu-Comm Adaptor (optional).

4. Test and use.

STEP ONE: Connecting to Two-Way Radio

To connect your Blu-Comm Adaptor to a two-way radio, follow these steps:

*Plug the Blu-Comm Adaptor into the speaker-microphone / audio accessory jack of your two-way radio.

Always turn oﬀ your two-way radio before connecting the Blu-Comm Adaptor.

On some models of two-way radio, you may need to tighten a retaining screw to ensure that the

Blu-Comm Adaptor remains attached to the radio.

Turn on your two-way radio. Because no wireless audio accessory will yet be paired to the

Blu-Comm Adaptor, received signals should be muted.

*The Talk button on the Blu-Comm Adaptor will function as a Push-to-Talk button. However the internal

microphone in your portable radio will be disabled as long as the Blu-Comm Adaptor is attached.

Mic audio will be muted until a wireless audio accessory is successfully paired to the adaptor, or a wired

audio accessory with a microphone is plugged into the Quick-Disconnect port.

Connecting the Adaptor to Radio

STEP TWO: Pairing with an Audio Accessory

*Turn the radio on while holding down the Talk button on the Blu-Comm Adaptor.

Turn oﬀ the radio that the Blu-Comm Adaptor is connected to. Wait at least three seconds.

*Continue to hold the Talk button down for approximately three seconds. Release the Talk button

when the status LED begins to ﬂash two times per second.

*The Blu-Comm Adaptor is now in audio accessory pairing mode. Activate the pairing mode on your

compatible wireless audio accessory.

*Once the wireless audio accessory and Blu-Comm Adaptor are paired with each other, the status LED

on the adaptor will show a constant blue light for three seconds.

*If the Blu-Comm Adaptor does not detect a compatible wireless accessory within 60 seconds of being

put into pairing mode, the adaptor will exit the pairing mode and resume normal operation.

*Once successfully paired, you will be able to operate your two-way radio using your compatible

wireless accessory.

Pairing With an Audio Accessory

#1 #2Wireless Accessory

Communications Priority

Audio accessory

connected toQuick

Disconnect Port

The Blu-Comm Adaptor will mute both the internal microphone and speaker of your portable radio

if no wireless audio accessory is paired with the device and no wired audio accessory is connected

to the QuickDisconnect port. You should detach the Blu-Comm Adaptor from the radio when no

audio accessory is in use.

STEP FOUR: Transmit and Receive Operation

The Blu-Comm Adaptor will automatically route radio calls based on the following priority:

*If an audio accessory is connected to the Quick-Disconnect Port of the Blu-Comm Adaptor

radio calls will be routed to this accessory.

*If no wired accessory is connected, calls will be routed to a wireless accessory, if one is paired

with the Blu-Comm Adaptor.

*If no wireless headset or audio accessory is paired to the Blu-Comm Adaptor or the wireless

accessory is turned oﬀ, received calls will be muted and will not be heard as long as

the Blu-Comm Adaptor is attached to the radio..

NOTE:

several seconds for the audio from received radio calls to be routed appropriately.

Push-to-Talk can be activated by any of the following methods:

*Pressing and holding the Talk button of the Blu-Comm Adaptor

*Using the PTT button on a wired Quick-Disconnect accessory (if one is connected to the

Blu-Comm Adaptor)

When transmitting, the operator’s voice is picked-up by:

*The microphone in the wired-audio accessory connected to the Quick-Disconnect port on

the Blu-Comm Adaptor.

* If no audio accessory is paired with the Blu-Comm Adaptor, or the paired wireless audio

as long as the Blu-Comm Adaptor is attached to the radio.

* If no audio accessory is paired with the Blu-Comm Adaptor, or the paired wireless audio

NOTE: Your adaptor may mute your two way radio’s speaker, causing incoming calls to be

missed, in any of the following situations:

* The adaptor is attached to the two-way radio and no wireless headset or wired accessory

is paired

* Your wireless headset goes out of range of the Blu-Comm Adaptor

* Your wireless headset is turned oﬀ or runs out of battery power

* Local interference causes the Blu-Comm Adaptor and the wireless headset to lose pairing

STATUS LED MESSAGES

The meanings of the various status LED messages shown by the Blu-Comm Adaptor are

shown on the following table:

TROUBLESHOOTING

My wireless audio accessory will not pair with the Adaptor.

Follow the instructions to place the Blu-Comm Adaptor into the correct pairing mode and then

activate the pairing mode on the accessory. Make sure that the Blu-Comm Adaptor and

accessory being paired are within one meter of each other.

My wireless audio accessory or worked before, but is not working now.

Make sure that the Blu-Comm Adaptor is properly connected to the two-way radio and that the

radio is turned on. Ensure that your wireless audio accessory has a fully charged battery and is

turned on. If the devices will still not work, re-pair the Blu-Comm Adaptor to the wireless

accessories.

My radio shows "Keyloader" on the LCD when I press the Talk button of the Adaptor.

When your press the talk key with no wireless headset paired, the radio believes a keyloader is

attached to the radio. Disable the keyloader function in the radio's programming software or

pair a wireless accessory with the adaptor.

LED INDICATION

One flash per minute

Two flashes per minute

One long flash for three seconds

No indication

MEANING

Normal operation

Audio accessory pairing mode active

Successfully paired or re-paired

Radio is turned off

Status LED

The Bluetooth word mark and logos are owned by the Bluetooth SIG and used under

license by Klein Electronics, Inc.

DISCLAIMER:The wireless link used by Blu-Comm products is an open standard,

unsecured technology. Additionally, this product can mute the portable radios internal

The Kenwood series works with 4-digit models, i.e. TK-3180, but not 3-digit models.

This product is not recommended for ﬁrst-responder or other mission critical users.

speaker and microphone if used with no wireless or wired audio accessory connected.

Names and logos used are the property of their respective owners.

Indice

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente