Blu SA0504 Manuale utente
blu·stone™freestanding basins
Installation Guide
1 866 907 0122 blubathworks.com
2016-08
SA0504
SA0505
SA0506
SA0507
SA0505N44
1 866 907 0122 blubathworks.com
2016-08
1
Attention — Before Installation
- We recommend that the installation be done by a minimum of 2 people as a security precaution. Also make sure
to adopt the proper posture when lifting the basin.
- Adhere to all local building and plumbing codes. The diagrams in this guide are not construction plans. They are
visual aids.
- For best results, the oor must be level and the wall must be square with the oor.
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the xture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. The owner/user of the product must keep this information for future reference.
3. Consult local building codes to make sure the installation complies with standards.
4. Remove the unit from its packaging. Before disposing of it, inspect the unit to make sure its in good shape. Should
inspection reveal any damage or defect in the nish, contact your distributor. The warranty does not cover damages
or defects in the nish once it has been installed. Blu Bathworks’ responsibility for shipping damages ceases upon
delivery of the product in good order to the carrier. All complaints regarding damage due to transport must be made
directly to the carrier.
5. Place the unit in the bathroom before you start working. Conserve all nuts and bolts.
6. To protect the unit during installation, we recommend that you lay a piece of cardboard on the bottom.
7. If the unit is covered with polyethylene protective lm, do not remove until installation is complete to grant maximum
protection. However, remove lm where any two surfaces will be in permanent contact.
8. Verify that all dimensions on the plan are the same as the ones of the unit.
Installation Notes
Important! Install this product according to the installation guide. Product does have an overow. Spout must provide a
minimum of 5” reach for adequate clearance into basin. Our products must be installed by certied professionals only
and according to our installation guide as well as federal, provincial / state and local building codes and regulations.
Technical Support Assistance
If further assistance is required, please contact:
Product Support at 1.866.907.0122 (09:00 – 17:00hrs PST) or email [email protected]
North America
Blu Bathworks Inc.
188 Smithe Street,Vancouver, BC, Canada, V6B 6A9
T +1.604.299.0122 F +1.604.299.0125
Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service.
2
1 866 907 0122 blubathworks.com
2016-08
Installation for Freestanding Basins
SA0504 / SA0505 / SA0506 / SA0507
PREPARATION
1. Place pedestal into installed position. Ensure product is level when placed and mounting holes are located at the
sides.
2. Carefully mark the mounting hole locations for the pedestal onto the oor with a non-permanent marker.
3. To help recall the pedestal position, trace a line along the base of the pedestal.
4. Carefully remove the pedestal.
PEDESTAL INSTALLATION
5. Drill pilot holes for the oor mounting brackets 1⁄2” (12mm) inside the line.
6. Install the pedestal mounting hardware provided. Place a metal washer onto the bolts and insert the bolts through the
mounting brackets into the oor securely. Fig 1.
7. Return the pedestal into position with the mark on the oor.
8. Install the pedestal bracket to oor using the two supplied screws. Fig 2.
WARNING: DO NOT OVERTIGHTEN. Overtightening may damage the products and cause personal injury and/or
property damage.
Line of basin
Floor mounting
brackets
11"
Rear
cut-out
for drain
Min 2" (51mm)
Max 3” (76mm)
from finished wall
¾" Mounting holes
1
2All dimensions based on
recommended 3” gap between
nished wall – actual distance
based on spout length to be
conrmed by installer
½"
(12mm)
1½"
(35mm) ؼ"
Ø(8mm)
3
1 866 907 0122 blubathworks.com
2016-08
FAUCET AND DRAIN CONNECTIONS
(NOT SUPPLIED)
1. Connect the water supply to the faucet according to faucet
instructions.
2. Connect and tighten the trap to the drain.
3. Turn ON the water supplies to the faucet.
4. Purge air from the HOT & COLD water by running the water
for a few seconds.
5. Fill the lavatory with water.
6. Check for leaks at the water supply and drain connections.
SA0504 / SA0505 / SA0506 / SA0507
1 2
3 4
5FAUCET AND DRAIN CONNECTIONS
(NOT SUPPLIED)
1. Connect the water supply to the faucet according to faucet
instructions.
2. Connect and tighten the trap to the drain.
3. Turn ON the water supplies to the faucet.
4. Purge air from the HOT & COLD water by running the water
for a few seconds.
5. Fill the lavatory with water.
6. Check for leaks at the water supply and drain connections.
4
1 866 907 0122 blubathworks.com
2016-08
SA0505N44
1 2
3 4
5
Plastic Anchors for
Concrete Floor
Silicon
3¼"
¾"
14 "
[370]
silicon
FAUCET AND DRAIN CONNECTIONS
(NOT SUPPLIED)
1. Connect the water supply to the faucet according to faucet
instructions.
2. Connect and tighten the trap to the drain.
3. Turn ON the water supplies to the faucet.
4. Purge air from the HOT & COLD water by running the water
for a few seconds.
5. Fill the lavatory with water.
6. Check for leaks at the water supply and drain connections.
5
1 866 907 0122 blubathworks.com
2016-08
where water meets modern®
188 Smithe Street, Vancouver, BC V6B 6A9 Canada | T1.604.299.0122 | TF 1.866.907.0122 | F 1.604.299.0125 |
blubathworks.com
®
where water meets modern®
188 Smithe Street, Vancouver, BC V6B 6A9 Canada | T1.604.299.0122 | TF 1.866.907.0122 | F 1.604.299.0125 |
blubathworks.com
®
blu·stone™cleaning & repair guide
blu·stone™is Blu Bathworks’ signature eco-friendly stone collection; a durable, low maintenance and hygienic material that is high
pressure injection molded, non-porous and anti-microbial. blu·stone™products are stain, scratch and impact resistant, and easy
to clean: after each use, simply wipe with a soft cloth to remove any surface dirt.
routine care
• Never expose blu·stone™to petroleum based products, such as paint removers, oven cleaners or other solvents
(Note: personal hygiene products and cosmetics will NOT damage the surface)
• We recommend that stains are removed within 24 hours
• Do not directly cut on the blu·stone™surface
• Blu Bathworks does not recommend exceeding US/ Canada maximum hot water temperature regulations of 150ºF/65ºC,
respectively. Exceeding stated temperatures could result in damage to blu·stone™products
standard cleaning
For standard cleaning of both gloss and matte nishes, we recommend using widely available cleaning products such
as Mr. Clean, Fantastik, VIM, CIF etc. Matte nished products may occasionally require a mildly abrasive product.
blu·stone™matte finish:
• For more difcult stains, use a mildly abrasive cream cleanser such as Soft Scrub, Comet Soft Cleanser, CIF or VIM
blu·stone™gloss finish:
• Do not use abrasive products or cream cleansers
scratched or damaged surfaces
blu·stone™matte finish:
• Ensure there is no surface dirt by ushing with water
• Rub the 600-grit sanding block, provided, in a gentle circular motion
• Higher grit sandpaper may be required to blend the repaired area to match the existing product nish
blu·stone™gloss finish:
• Ensure there is no surface dirt by ushing with water
• We recommend sanding the area starting with 600, 800 and 1200-grit sandpaper: begin with the lower number (coarser)
grit followed with each higher number (ner) in ascending order
• Finish by polishing the surface using a cloth and white polishing compound for automobiles
repairs
For more extensive repairs, send a photograph of your blu·stone™ product to Blu Customer Service
([email protected]), who will inform you as to the most appropriate methods to use.
limited warranty
Blu Bathworks’ (“Blu”) warranty on blu·stone™ products covers all defects in materials and manufacturing for a period of ve (5)
years from the date of purchase. This limited warranty, starting on the original purchase date, is only offered to the original
purchaser who acquires the product directly from Blu or from its authorized dealers. This limited warranty does not apply to cases
in which a product was incorrectly installed, nor to damage due to negligence, misuse, thermal shocks, cigarettes, ames, natural
catastrophes or other accidents. Blu is not responsible for costs and claims that may arise from purchase of a product unsuited to
the structure of the existing building. Any transformation or alteration made to a Blu product automatically voids the warranty.
Blu’s warranty is limited to repair or replacement (with a product of equal value), provided the claim is made to an authorized dealer
or directly to Blu, within the warranty period. Labor costs and any other expenses entailed by replacement of a Blu product are not
covered by the warranty.
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Blu Prodotto idraulico
