bluBathworks blu-stone BT0110L Manuale utente
blu·stone™freestanding bathtub
InstallationGuide
BT0102.01
BT0104.01
BT0105.01
1 866907 0122 blubathworks.com
2020-06
BT0305.02
BT0110L
BT0110R
BT0402N16
BT0305N15
BT0305N17.01
BT0304N17
BT0402N17
BT0406.01
BT0408.02
BT0402.02
BT0304.01
BT0110L
BT0110R
BT0203.01
1
1 866 907 0122 blubathworks.com
2020-06
Attention — Before Installation
Thank you for choosing from among Blu’s quality line of products. We recommend that you carefully read this installation guide
to ensure your bathtub’s proper operation and reliability for many years to come.
WARNING: This bathtub is made of a quartzite stone and resin. The tub’s weight may vary between 300 and 440 lbs
(140 and 200 kg). We recommend that the installation be done by a minimum of 2 people as a security precaution. Also make
sure to adopt the proper posture when lifting the tub.
Adhere to all local building and plumbing codes. The diagrams in this guide are not construction plans. They are visual aids.
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the xture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. The owner/user of the product must keep this information for future reference.
3. Consult local building codes to make sure the installation complies with standards.
4. Remove the unit from its packaging. Before disposing of it, inspect the unit to make sure its in good shape. Should inspection
reveal any damage or defect in the nish, contact your distributor. The warranty does not cover damages or defects in the nish
once it has been installed. Blu Bathworks’ responsibility for shipping damages ceases upon delivery of the product in good
order to the carrier. All complaints regarding damage due to transport must be made directly to the carrier.
5. Place the unit in the bathroom before you start working. Conserve all nuts and bolts.
6. To protect the unit during installation, we recommend that you lay a piece of cardboard on the bottom.
7. If the unit is covered with polyethylene protective lm, do not remove until installation is complete to grant maximum protection.
However, remove lm where any two surfaces will be in permanent contact.
8. Make sure the bathroom oor is level and strong enough to support the weight of the water-lled bathtub. If you are renovating,
bring down the walls to install framing and plumbing. Make sure the walls are properly insulated and comply with the
appropriate building code.
9. Verify that all dimensions on the plan are the same as the ones of the unit.
10. If an apron is to be installed, make sure the bathtub is at the same height as the oor covering.
Installation Notes
Important! Install this product according to the installation guide. Floor support under bath must provide for a minimum
of 1600 lbs (725kg). Hot water supply should be 70% of capacity or greater. Installation will vary.
Technical Support Assistance
If further assistance is required, please contact:
North America
Blu Bathworks Inc.
188 Smithe Street,Vancouver, BC, Canada, V6B 6A9
T +1.604.299.0122 F +1.604.299.0125
Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service.
2
1 866 907 0122 blubathworks.com
2020-06
General Instruction before Installation
IMPORTANT: Ensure to check the bathtub for proper drainage before any draining is done.
• The bathtub is shipped with the waste and matching blu·stone™drain cover.
•Blu recommends that the tub be water tested before installation is complete. Fill the tub to overow and inspect for leaks.
•Decide exactly where you wish to install the bathtub and place the tub where it is to be installed and ensure the tub is level.
Note: Use 1½" (FIP) adaptor.
• Install the basic plumbing components: water inlet and waste. These tub models require a vertical plumbing connection from
the oor.
•Shims may be required to level the tub depending on nish oor surfaces. Shims are not included. When adjusting the level
allow a slight clearance (8") between the nished oor and the apron. Note: use a level to ensure accuracy.
• Connect the bathtub drain to the waste. Hook up the water to the faucet. Check that all connections are waterproof.
NOTE: The faucet cannot be installed on the bathtub. The tub ller must be mounted either in the wall or a freestanding
oor-mounted tubller. Read the manufacturer’s instructions for installation details.
3
1 866 907 0122 blubathworks.com
2020-06
Installation Instructions
PREPARATION
•Clean, level, and prepare the oor for installation.
•Place the unit in the exact installed position on the oor and trace the outline of the bath with a pencil or any erasable
marking. (Fig. 1)
•Determine the location of the drain pipe on the oor by taking measurements of the drain and waste location underneath
the unit. (Fig. 2)
Note: Drain and waste locations will vary by model.
• Using a blanket, cardboard, or other clean protective surface, turn the unit on its side so that the unit is properly
supported during drain installation.
• Clean the drain hole area in preparation of setting the drain. The area should be dry and free of any debris.
- wear protection - two people recommended
1 2
3 4
INSTALL DRAIN HARDWARE
• Apply a bead of clear silicone around the drain body and pass it through the drain hole. (Fig. 3)
• Apply silicone over the bottom of the drain body. (Fig. 4)
• Attach the drain body nut on the drain body and tighten until the nut and washer have created a seal with the
bottom of the bathtub.
* DO NOT overtighten
4
1 866 907 0122 blubathworks.com
2020-06
INSTALL BATHTUB
• Apply a generous bead of adhesive or silicone to the bottom of the tub supports. (Fig. 6)
• Apply a bead of tub and tile caulk around the edge of the base. (Fig. 6)
• Carefully set tub into position (Fig. 7) and connect the drain hardware (previously installed).
Finish the installation of the tail piece.
PREPARE THE TAIL PIECE
All parts involved in tail piece installation are provided by the
installer (Fig. 5).
• Waste drain must always be installed according to local
standard. Verify the placement of the bathtub before
drilling the hole for the waste drain.
• Install 1½" rubber slip gasket over the waste drain.
•Alternatively, Blu Bathworks recommends BTWaste.RN Island
Tub Drain*** for easy installation of freestanding bathtubs.
(Provided by customer)
• Cut tail piece to desired length
(will vary for each installation)
•Slide tail piece nut over tail piece towards anged end.
•Place ange washer on top of tail piece.
• Connect tail piece assembly to waste drain.
5
6 7
Island Tub Drain Installation ***
Refer to BTWaste.RN Installation Guide
a
a
drain body
trap*
silicone drain gasket
on top of the tub
drain body nut
tail piece*
Island Tub Drain***
floor
provided by installer*
1x pop up cover in chrome
1x pop up cover in blu·stone™**
silicone drain gasket
at the bottom of the tub
flat
lip
top of
the tub
bottom
of the tub
tail piece nut
included
5
1 866 907 0122 blubathworks.com
2020-06
COMPLETE INSTALLATION
•Fill the tub with water to the overow and then drain the tub while inspecting the waste connections below the oor for
leaks. Access from below will be necessary for this step (Fig. 8).
•With the bathtub now in place, wipe o any excess tub and tile caulk and adhesive where the tub meets the oor.
•Run a bead of tub and tile caulk around the bottom edge of the bathtub where it meets the oor. Wipe o any excess
caulk withh a wet cloth (Fig. 9).
8 9
Note: This installation is recommended by Blu Bathworks. Our products must be installed by certied professionals only and
according to our install recommendations as well as federal, provincial / state and local building codes and regulations.
ALCOVE INSTALLATION USING TILE FLANGE
BT0102.01 · BT0110L/R · BT0114L/R · BT0104.01 · BT0105.01 · BT0203.01
In order to maintain the symmetry of these narrow rim tub models in an alcove installation, the following points
& illustration are provided below.
1. Determine wall nish material and its thickness
2. Install tile ange on corner edge of bathtub using high density silicone above and below
lip of TF.BTSB tile ange as shown in Detail I (exploded)
3. Install bathtub
4. Install wall nish
5. Apply a clear silicone bead where the tub and wall nish meet at the ange location
**Blu Bathworks recommends TF.BTSB Tile Flange (Sold separately)
DETAIL I
DETAIL I (exploded)
Silicone
above & below lip
6
1 866907 0122 blubathworks.com
2020-06
ALCOVE INSTALLATION EXAMPLES
BT0110L/R, BT0114L/R, BT0102.01,
BT0104.01, BT0105.01 + BT0203.01
7
1 866 907 0122 blubathworks.com
2020-06
T1.604.299.0122 | TF 1.866.907.0122 | F1.604.299.0125 | blubathworks.com
blu·stone
™
cleaning & repair guide
blu·stone™is Blu Bathworks’ signature eco-friendly stone collection; a durable, low maintenance and hygienic material that is high
pressure injection molded, non-porous and anti-microbial. blu·stone™products are stain, scratch and impact resistant, and easy
to clean: after each use, simply wipe with a soft cloth to remove any surface dirt.
routine care
• Never expose blu·stone™to petroleum based products, such as paint removers, oven cleaners or other solvents
(Note: personal hygiene products and cosmetics will NOT damage the surface)
• We recommend that stains are removed within 24 hours
• Do not directly cut on the blu·stone™surface
• Blu Bathworks does not recommend exceeding US/ Canada maximum hot water temperature regulations of 150ºF/65ºC,
respectively. Exceeding stated temperatures could result in damage to blu·stone™products
standard cleaning
For standard cleaning of both gloss and matte nishes, we recommend using widely available cleaning products such
as Mr. Clean, Fantastik, VIM, CIF etc. Matte nished products may occasionally require a mildly abrasive product.
blu·stone™matte finish:
• For more dicult stains, use a mildly abrasive cream cleanser such as Soft Scrub, Comet Soft Cleanser, CIF or VIM
blu·stone™gloss finish:
• Do not use abrasive products or cream cleansers
scratched or damaged surfaces
blu·stone™matte finish:
• Ensure there is no surface dirt by ushing with water
• Rub the 600-grit sanding block, provided, in a gentle circular motion
• Higher grit sandpaper may be required to blend the repaired area to match the existing product nish
blu·stone™gloss finish:
• Ensure there is no surface dirt by ushing with water
• We recommend sanding the area starting with 600, 800 and 1200-grit sandpaper: begin with the lower number (coarser)
grit followed with each higher number (ner) in ascending order
• Finish by polishing the surface using a cloth and white polishing compound for automobiles
repairs
For more extensive repairs, send a photograph of your blu·stone™ product to Blu Customer Service
limited warranty
Blu Bathworks’ (“Blu”) warranty on blu·stone™ products covers all defects in materials and manufacturing for a period of ve (5)
years from the date of purchase. This limited warranty, starting on the original purchase date, is only oered to the original
purchaser who acquires the product directly from Blu or from its authorized dealers. This limited warranty does not apply to cases
in which a product was incorrectly installed, nor to damage due to negligence, misuse, thermal shocks, cigarettes, ames, natural
catastrophes or other accidents. Blu is not responsible for costs and claims that may arise from purchase of a product unsuited to
the structure of the existing building. Any transformation or alteration made to a Blu product automatically voids the warranty.
Blu’s warranty is limited to repair or replacement (with a product of equal value), provided the claim is made to an authorized
dealer or directly to Blu, within the warranty period. Labor costs and any other expenses entailed by replacement of a Blu product
are not covered by the warranty.
Questo manuale è adatto per i seguenti modelli
15
Indice
Altri manuali bluBathworks Vasca
Manuali Vasca popolari di altre marche
Lyons
Lyons Elite ETLxx663219 Series Manuale utente
Woodbridge
Woodbridge BJ500 Istruzioni per il montaggio
Whirlpool
Whirlpool Ariel ARL-702 Manuale utente
TEIKO
TEIKO EXCELLENT DUO Manuale utente
American Standard
American Standard Colony 5-1/2' x 32" Manuale utente
American Standard
American Standard 3052OD.X0X Guida rapida
