Blueant ENDURE Manuale utente
ENDURE
USER GUIDE
Read Me to Get the Most Out of
Your Device...
• ENGLISH
• FRANÇAIS
• ESPAÑOL
Endure Quick Start Guide: English
1
Indicator
Light
Vol -Vol +
Command
Button
Microphones
Model: T2
Charge Your Headset
Your headset has been given an initial partial charge to get started,
but for best results charge it using the supplied USB cable and
adaptor until the indicator light turns white.
> Charge the Endure whenever it announces the battery is Very Low.
> Your headset features Rapid Charge technology. It will charge to
50% capacity in just 30 minutes. A full charge takes about 2 hours.
> During charging, the indicator light flashes red.
> When the light goes white, the charge is complete.
> The Endure features an iPhone headset battery meter so you can
check your battery status at a glance.
2
USB Connector
(lift cover to access)
Power
Switch
Wearing the Endure
You can wear your
headset on either ear.
For best results:
> Position the hook
and ear gel as
shown here.
> Make sure the
headset is angled
towards your mouth.
Pair Your Headset
1. Slide the power switch across to turn the Endure on.
2. Put the Endure in your ear.
3. The first time you use the Endure it will go straight to pair mode
and talk you through the pairing process.
For subsequent pairings, make sure the Endure is not connected to
any phones, then hold down the Command button. The Endure will
announce it is going into pairing mode.
Tip: The pairing code is 0000 (four zeros).
3
4
LEFT
EAR
RIGHT
EAR
Pairing mode will time out after 2 minutes. To go back into pairing
mode, press and hold the Command button. To cancel pairing mode,
turn the Endure off and back on again.
Transfer Your Phonebook
Once the pairing is complete, your headset will attempt to transfer
your phonebook contacts so that it can announce the names of
incoming callers. Please accept any connection requests on your
phone from the Endure and wait for the transfer to finish.
Some phones do not support automatic phonebook transfers. If
the Endure announces that this is the case, you need to go to your
phone’s address book and send contacts via Bluetooth to the Endure.
See “Phonebook Troubleshooting” or www.blueantwireless.com
for help.
Note: Whenever you add contacts to your phone in future you must
update your phonebook on the Endure: with the headset connected
to your phone but not on a call, hold down the Command button for 3
seconds to initiate a phonebook update.
Making Calls
Voice Dialing
To use this feature your phone must support voice dialing over
5
6
Bluetooth.
1. Double click the Command button.
2. The Endure activates your phone’s voice dial feature (if available).
Once you have activated the voice dial feature, you are using your
phone’s voice recognition software. Please check your phone manual
to find out what commands your phone supports.
> On the iPhone 4S this command activates Siri. There’s no need to
touch or unlock your phone. Note: Siri must be enabled on your
phone. Go to Settings > General on your iPhone and check that Siri
is set to ON.
> Android™ users: use this command to activate Google Voice
Actions (if available). Note: Depending on your handset, you may
need to disable the phone password lock to use voice dialing over
Bluetooth. Check your phone manual for further information on
this feature.
Other Ways To Make Calls
> Dial the number on your phone. The audio automatically transfers
to the headset.
> Hold down Vol + for 1 second to redial the last outgoing call.
> Hold down Vol - for 1 second to call back the last incoming call.
Taking Calls
When the phone rings, you can answer with your voice: wait for the
prompt to ask you if you want to take the call, and then say Answer
or Ignore.
If you don’t want to wait for the prompt, or you are in a noisy place:
> Click the Command button once to accept the call.
> Double click the Command button to reject the call.
During a call, click the Command button to end the call.
Multipoint
Up to 2 phones can connect to the Endure at the same time. To pair
a second phone:
1. Use your phone’s Bluetooth menu to disconnect the existing paired
phone from the Endure.
2. With the Endure switched on, hold down the Command button until
the Endure starts to talk you through the pairing process.
3. When the pairing is complete, use the Bluetooth menu on each
phone to reconnect them to the Endure.
When you have 2 phones connected, you can always answer a call
on either phone. If you initiate a call through the Endure, or activate
8
7
phone voice dialing, it will happen on the “primary phone”: the one
that connected to the headset first.
Listening to Audio
The Endure supports A2DP audio streaming: if your phone or
Bluetooth device supports the A2DP profile then simply start playing
music or any other audio (including directions from a GPS application
on the phone) and it will automatically transfer to the headset.
The audio will mute automatically if you make or receive a phone call,
and resume when the call ends.
Note: The Endure only supports A2DP bluetooth audio streaming
from one phone at a time.
Reset your Endure
If you are having problems with the Endure, you can reset it and start
again:
1. Disconnect the Endure from your phone by deleting the pairing
from your phone’s Bluetooth menu.
2. Turn your phone off and back on again to clear its memory.
3. With the Endure switched on, but not connected to any phones,
hold down all three buttons (Vol +, Vol -, and the Command button)
for about 3 seconds.
9
10
The Endure will reset and go straight to pairing mode. You will now
need to pair your phone with the Endure again.
Free Android Application
> Reads your incoming text messages
> Helps with pairing and setup
Go to the Android Market and search for “BlueAnt” to download and
install this free application. Once the application is installed you will
hear your text messages read aloud automatically on your BlueAnt
device as they come in.
Supports Android handsets running Android version 2.1 or above.
Android is a trademark of Google, Inc, and its use is subject to its
permissions.
11
Scan this code on your
phone with a QR code
reader to download the
application:
Phonebook Troubleshooting
When you pair your phone the Endure attempts to transfer the
contacts from your phonebook so that it can announce the names of
incoming callers.
Note: If your phone prompts you to allow a connection to the Endure,
you must select “YES” or “OK”.
Android™
On Android devices a message about the
phonebook transfer may appear in the
notifications area at the top of the screen.
In order to transfer your contacts you must
swipe your finger over this message and
accept the phonebook transfer request from
the Endure.
If you miss this step you will need to:
1. Delete the pairing from your phone.
2. Power the phone off and back on.
3. Reset your Endure and pair it with your phone again.
This is due to the way the Android PBAP request system works.
12
12a Phonebook Access Request
Notification
shown on
Android
devices
Altri manuali per ENDURE
1
Indice
Lingue:
Altri manuali Blueant Cuffia
Blueant
Blueant T1 Manuale utente
Blueant
Blueant X3 MICRO Guida all'installazione
Blueant
Blueant T2 ENDURE Manuale utente
Blueant
Blueant Q3i Manuale utente
Blueant
Blueant Q1 Manuale utente
Blueant
Blueant Z9i Guida rapida
Blueant
Blueant X3 MICRO Manuale utente
Blueant
Blueant T2 ENDURE Manuale utente
Blueant
Blueant Q1 Manuale utente
Blueant
Blueant Q3 Manuale utente
Blueant
Blueant V1 Manuale utente
Blueant
Blueant X3 MICRO Manuale utente
Blueant
Blueant Q2 Manuale utente
Blueant
Blueant V1 Manuale utente
Blueant
Blueant Z9i Manuale utente
Blueant
Blueant Interphone none Manuale utente
Blueant
Blueant V12 Guida all'installazione
Blueant
Blueant V1 Manuale utente
Blueant
Blueant ENDURE Manuale utente
Blueant
Blueant Z9i Manuale utente
