BlueUp BlueBeacon Gateway W Manuale utente

BlueUp S.r.l.s.

Loc. Belvedere, Ingresso 2, 53034 Colle di Val d'Elsa SI) - ITALY

Ph. 347 4123206, Fax 0577 043101

E-mail: [email protected], Web: www.blueupbeacons.com

VAT N. IT 01373980521

BlueBeacon Gateway

User manual

Introduction

BlueBeacon Gateway is a BLE-beacon gateway with BLE and LAN/WLAN interfaces that

allows to communicate with BLE beacons new software manages both scanning for

generic BLE beacons and connecting to BlueBeacon beacons).

BlueBeacon Gateway is offered in two alternative versions:

•BlueBeacon Gateway D for desktop applications;

•BlueBeacon Gateway W for wall installations.

BlueBeacon Gateway D is provided in a plastic enclosure suitable for desktop applications

optional mounting kit is available). It is available in one version:

- D/A00: with integrated omnidirectional BLE antenna.

BlueBeacon Gateway W is provided in an elegant plastic enclosure suitable for wall or

ceiling installation. It is available in three versions:

- W/A00: with integrated omnidirectional BLE antenna;

- W/A05: with internal 5dB-directive BLE antenna;

- W/SMA: with SMA connector for external BLE antenna.

Possible applications with BlueBeacon Gateway are:

- remote monitoring and management of beacons;

- localization of BLE beacons tags) for RTLS and access control;

- distributed monitoring systems of environmental parameters, using BlueBeacon Sensor

with temperature, humidity and pressure sensors);

Before you start using a BlueBeacon Gateway, verify that it is undamaged and carefully

read the instructions in this user manual, particularly the indications in the "Safety" section.

BlueUp S.r.l.s. disclaims any and all liability if the devices are used in modes and

environments incompatible for keeping the product’s intact, safe and in operation.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 1/28

Technical characteristics

Hardware

Platform: Quad Core 1.2GHz Broadcom BCM2837 64bit CPU

Connectivity: Ethernet, WiFi

Radio (Bluetooth)

Version: 4.1 Bluetooth Smart Low Energy)

Frequency: 2.402 to 2.480 GHz

Antenna: D/A00: desktop-version with integrated omnidirectional chip antenna;

W/A00: wall-version with integrated omnidirectional chip antenna;

W/A05: wall-version with internal 5dB-directive antenna;

W/SMA: wall-version with SMA connector for external antenna.

Electrical specifications

Voltage: 5VDC micro-USB)

Current: 1.5A typ.)

Mechanical and environmental specifications

Size: Ver. D: 100 x 73 x 30 mm

Ver. W: 120 x 120 x 45 mm excluding flanges)

Mounting kit: Ver. D: none

Ver. W: wall-mounting plastic flange

IP protection: IP40

Operating temperature: -20°C to +60°C

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 2/28

Safety

These information are an integral and essential part of the product BlueBeacon Gateway )

and must be delivered to the user. Read them carefully as they contain important

information regarding the installation, use and maintenance.

Warnings

BlueBeacon Gateway W must be intended for use for which it was designed. Any other

use is considered improper and therefore dangerous.

Before you start using BlueBeacon Gateway W, verify that it is undamaged.

DO NOT use BlueBeacon Gateway W in potentially explosive atmospheres. The presence

of flammable gas or fumes is a serious safety hazard.

Make sure that BlueBeacon Gateway W is always kept in a dry environment.

The company BlueUp S.r.l.s. disclaims any liability for damages caused by an inadequate

use of the device and the failure to observe the information provided herein.

Power

The device must be powered via the micro-USB port with a 5VDC power-supply. Use an

AC/DC plug-in power adapter with USB output and USB-to-microUSB power cable. The

power supply must be capable of supplying a current of at least 1.5A. The external power

adapter must comply with applicable standards and regulations in the country of use.

Do not power the device with power voltages other than 5VDC. Power supply with

voltages other than 5VDC may irreversibly damage the device, as well as cause potential

safety hazards.

Waste disposal

In implementing the Directives 011/65/EU and 01 /19/EC on the restriction of the

use of hazardous substances in electrical and electronic equipment and the

disposal of waste.

The crossed bin symbol on the appliance or its packaging indicates that at the end of the

product’s life, it must be collected separately from other waste. The user must, therefore,

take the remote control to an authorized disposal center for collection of electronic and

electrical waste, or return it to the dealer when purchasing a new similar appliance, on a

one to one basis. Appropriate separate collection for the subsequent forwarding of the

product sent for recycling, treatment and environmentally compatible disposal helps to

prevent negative environmental and health effects and promotes the reuse and/or

recycling of materials making up the equipment. Illegal dumping of the product by the user

entails the application of administrative sanctions in the current provisions of law.

For more information about the collection systems, contact your local authorities.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 3/28

In implementing Directive 006/66/EC on the reduced use of hazardous substances

in batteries and the disposal of the same.

The crossed bin symbol on the appliance or its packaging indicates that the batteries must

not be disposed of with the rest of the household waste, as they may contain substances

that are potentially harmful to the environment and health. Remove the old battery from the

device and turn it in at the appropriate collection points.

Disclaimer

This manual is intended to provide a brief summary of our knowledge and some guidance

regarding the use of the device and its accessories. The information contained herein has

been provided by sources that BlueUp S.r.l.s. considers to be dependable and is accurate

to the best knowledge of the company. This sheet is not intended to be an inclusive

document on worldwide hazard communication regulations. The information is provided in

good faith. Each user of this material needs to evaluate the conditions of use and define

the appropriate protective mechanisms to prevent the exposure of persons, property

damage or release to the environment.

BlueU S.r.l.s. assumes no res onsibility for injury to the reci ient or third ersons,

or for any damages resulting from misuse of the device and its arts.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 4/28

Device connection and setu

BlueBeacon Gateway comes with the following default network configurations:

•Ethernet network interface: Enabled with DHCP

•Wifi network interface: Disabled

To access the BlueBeacon Gateway administration interface, you need a LAN

infrastructure with at least one device offering IP address assignment DHCP Server).

Usually any commercial router integrates a DHCP Server.

Connect BlueBeacon Gateway with an ethernet cable to your LAN network, then power

BlueBeacon Gateway via the MicroUSB connector - we recommend using a power supply

with the following features:

•Input: 100-240V ~ 50 / 60Hz

•Output: 5V 1.5A �

Once powered, BlueBeacon Gateway will begin the boot process of the operating system

and the necessary software components. When the green LED will start to flash

heartbeat-blink) BlueBeacon Gateway will be fully operational.

In case of incorrect network configuration or problems such that the BlueBeacon Gateway

administration interface is no longer reachable on the network, it is possible to restore the

factory settings using the reset button located on the bottom of the device under the

Ethernet connector) . By keeping this button pressed for at least 5 seconds, the green LED

will remain on and the device will start the reset procedure. At the end of the procedure,

BlueBeacon Gateway will automatically reboot and the green LED will flash again

indicating the correct execution of the software on board.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 5/28

5VDC ETH

ETH

5VDC

Get into the administration interface

BlueBeacon Gateway has a web interface to manage all its features. The web interface is

reachable at the IP address of the device.

BlueBeacon Gateway comes with a pre-configured ethernet interface to use DHCP.

So, in order to access the web interface the first time you boot BlueBeacon Gateway, you

need a device usually a commercial router) with DHCP Server functionality enabled.

When your router has assigned an IP address to the BlueBeacon Gateway you need to

identify the IP address assigned and then point your browser to this IP.

Figure 1 shows an example of identifying the IP address assigned to the BlueBeacon

Gateway by a SpeedTouch router.As you can see, BlueBeacon Gateway is identified by its

hostname which consists of the string BBGW-CPU_SERIAL_NUMBER.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 6/28





Administration interface: Login

Once the BlueBeacon Gateway IP address is identified, to access the administration

interface, simply point the browser to the BlueBeacon Gateway IP address, as shown in

Figure 2.

At this point, the login screen will appear on the browser Figure 3).

The default password to be used at the first start is blueup.

Once logged in, you will be redirected to the index page of the BlueBeacon Gateway

administration interface.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 7/28

 !

"

#$



Administrative interface: Overview

Figure 4 shows an overview of the BlueBeacon Gateway administration interface.

On the left side you can see the sidebar of the menus, where are the buttons to access the

following pages:

•System Info : contains information and system configurations

•Network Settings : allows you to view and edit network configurations

•BlueBeacon Cloud : allows you to register BlueBeacon Gateway at the BlueBeacon

Cloud portal and then monitor and manage the beacon remotely

•Beacons : displays information about the beacon currently received by BlueBeacon

Gateway

•HTTP Callbacks : allows you to configure HTTP callbacks to automatically send

beacon data to a server

•Beacon RSSI : displays a plot of the received signal strength indication RSSI)

•Docs : documentation related to the REST APIs provided by BlueBeacon Gateway

At the top you can view the topbar, where in the top right menu you have access to the

features of:

•Reboot , restart of BlueBeacon Gateway

•Shutdown , shutdown of BlueBeacon Gateway

•ogout from the administration interface

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 8/28

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 9/28

%

Administrative interface: System Info

The System Info tab displays the main information and system configurations Figure 5).

System information is grouped into:

•General Info : general information

◦Firmware version : version of the BlueBeacon Gateway software package

◦Hostname : system hostname, default BBGW-CPU_SERIAL_NUMBER

◦System Timezone : system timezone, the default value is Europe / Rome, but it

can be changed by selecting the timezone among those available

◦System Time 11: system date and time, varies according to the chosen timezone

◦System Uptime : system uptime, indicates how long BlueBeacon Gateway is

active

•Device Identifiers : unique serial identifiers of the system

◦Machine ID : unique id generated when first started

◦CPU Serial : unique ID of the CPU

◦uSD Serial : unique ID of the SD-CARD

•Network Interfaces : configuration of active network interfaces

•ogin Password : allows you to change the password for accessing the BlueBeacon

Gateway administration interface

•Firmware Upgrade : allows you to upgrade the software developed by BlueUp

requires the upload of the software package released by BlueUp)

Administrative interface: Network Settings

The Network Settings tab displays and allows you to configure the BlueBeacon Gateway

network interfaces Ethernet and WiFi) Figure 6).

For each network interface you can choose whether to use DHCP or static IP, configure

the default gateway and the DNS servers to be used.

Regarding the wireless network interface, you will also need to specify:

WLAN country code: country code to select from those available

1 BlueBeacon Gateway in the basic version, does not have a dedicated RTC but sets and maintains the

system time using NTP Network Time Protocol). The NTP protocol defines a client / server mechanism

with which an operating system can keep the system time synchronized using NTP remote servers.

Therefore, to be able to maintain the system time, it will be necessary that BlueBeacon Gateway is

connected to a LAN that allows BlueBeacon Gateway to reach the remote NTP servers on the web.

BlueUp S.r.l.s. - 2018 V1.0– 26/06/2018 10/28

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente