Blyss NT10SSR Manuale utente
EN
DRY INERTIA CERAMIC HEATER
NT10SSR 840-1000W 3663602688600
NT15SSR 1250-1500W 3663602688631
NT20SSR 1680-2000W 3663602688662
Let’s
get started…
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
Getting started… 02
Safety
Before you start
Quick start
03
06
11
In more detail… 17
Technical and legal information
Care and cleaning 18
22
23Environment protection
02EN
Safety
PLEASE READ SAFETY INSTRUCTIONS CAREFULLY
BEFORE USING THE UNIT.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
Children of less than 3 years should be kept away
unless continuously supervised.
Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided that
it has been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3 years and less than 8 years
shall not plug in, regulate and clean the appliance
or perform user maintenance.
CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention has to
be given where children and vulnerable people are
present.
03EN
Safety
If the power cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
The appliance should not be placed immediately
below a socket.
WARNINGS: In order to avoid overheating, do
not cover the heater.
Do not use this heater with a programmer, timer,
separate remote control system or any other device
that turns on the heater automatically because
there is a risk of fire if the device is covered or
placed incorrectly.
CAUTION: To avoid hazard due to inadvertent
resetting of the thermal cutout, this appliance must
not be powered via an external switch, such as a
timer, or connected to a circuit that is regularly
switched on and off by the electricity supplier.
This heater must not be disposed of with household
waste; it must be taken to a local centre of
recovery and recycling of electrical appliances.
The heater must be installed so that switches and
other control devices can not be touched by a person
in the bath or shower.
A means of disconnection from the power supply
having a contact opening distance of all poles must
be included in the fixed wiring in accordance with
the installation requirements.
04EN
Safety
If being fitted in a bathroom, a 30mA RCD must
be used.
With respect to the details of how to install the
appliance onto the wall, refer to "INSTALLATION"
on pages 9-10.
05EN
For domestic use only.
Never allow children or persons unable to operate the
appliance safely to use this appliance without supervision.
Please dispose of plastic bags carefully and keep them
away from children.
This appliance is for indoor use only.
Observe the minimum distances as shown in Fig. 1.
Do not install the unit in place where air flow that may
disturb its regulation(e.g. under an air conditioning unit)
Before you start
The power connection is made by the 2 cables via a
connection box. In places such as wet bathroom,
laundry, kitchen, install the appliance at least 250 mm from
the level of the ground.
Things to check before you start
1. Body
2. Control panel
Your product
INSTALLING THE APPLIANCE?
3. Wall-mounted kits
2
1
06EN
Description Drawing QTY
Screw
Wall plug
4
4
3
Before you start
This heater is for wall mounting only. Do not attempt to use it
free standing.
You need to follow the below requirements when you install
your heater:
- Means for disconnection having a contact separation in all
poles must be incorporated in the fixed wiring in accordance
with the wiring rules.
- Warning: you need to connect the two conductors of the
supply cable to a connection block in respecting the
polarities as following:
IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Blue – Neutral
Brown – Live
The blue wire must be connected to the terminal marked with
an N or coloured black.
The brown wire must be connected to the terminal marked
with an L or coloured red.
WARNING: Never connect live or neutral wires to the earth
terminal.
This product is double insulated and must not be
earthed. If there are any incoming earth cables, they must be
joined together using a suitable connector (not supplied) and
well insulated with good quality insulation tape. This is to
ensure earth continuity throughout your property.
All fittings must be installed by a competent person in
accordance with the current IET Wiring Regulations
(BS7671). If in doubt, consult a qualified electrician.
THIS PRODUCT IS SUITABLE FOR BATHROOMS ZONE
2 AND OUTSIDE ZONE;
07EN
Before you start
This product is suitable for use in living areas, and Bathroom
dry (Outside) Zones only (see diagram below and current
IET Wiring Regulations for details). It is not suitable for
moisture is likely. If being fitted in a bathroom a 30mA RCD
must be used. This appliance does not come fitted/supplied
with a fused plug. DO NOT wire/fit a plug to this appliance.
The appliance must be electrical connected to a fused fixed
spur, which is fitted with a 13Amp fuse.
Always refer to the Reference Drawing for Bathroom
Installation.
Note: the below drawing is for reference only.
We suggest you to contact a professional electrician for any
help.
* Full details can be found in the current IET Wiring
Regulations (BS7671)
0.6m
0.6m
ZONE
2
Window
recess
(DRY) OUTSIDE ZONES
ZONE
2
ZONE
1
2.25m
Ceiling
THIS PRODUCT IS SUITABLE FOR BATHROOMS
ZONE 2 AND OUTSIDE ZONE;
ZONE
0
Bathroom Zones 0,1, or other areas where contact with
08EN
Before you start
INSTALLATION
09EN
To hang the heater on the wall:
1. Choose a suitable installation location for the
heater. (Figure 1)
2. Disassemble the wall bracket by loosening the
screw (do not remove, only loosen) and slide the
metal plate out of the hole. Take out the bracket by
pulling down (Figure 2).
3. Verify that the bracket is horizontal with a spirit
level and mark the location of 4 holes on the wall.
Drill 4 holes in the wall using a drill adapted to
the diameter of wall plug. Insert the wall plug into
the holes,then screw securely wall mount bracket
onto the wall. (Figure 3)
4. Place the heater against bracket (Figure 4):
A : Align the heater on the 2 lower hooks that are
downwards.
B : Pull the heater upwards whilst retaining it in the
2 lower hooks.
C : Align the heater on the 2 upper hooks that are
upwards.
D : Pull the heater down.
5. Slide the metal plate into the hole, and fasten the
screw to lock the wall mount bracket (Figure 5).
Before you start
10EN
Questo manuale è adatto per i seguenti modelli
5
Indice
Lingue:
Altri manuali Blyss Stufa
Blyss
Blyss Wickham 3663602847533 Manuale utente
Blyss
Blyss 3663602845027 Manuale utente
Blyss
Blyss Thorpe 3663602847595 Manuale utente
Blyss
Blyss WDH-122E Manuale utente
Blyss
Blyss NPO Manuale utente
Blyss
Blyss Ellesmere 3663602844822 Manuale utente
Blyss
Blyss NT20-12A Manuale utente
Blyss
Blyss 3663602844624 Manuale utente
Blyss
Blyss Wickham Manuale utente
Blyss
Blyss KPT-2000B 5203L Manuale utente
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente