BOCK FK20/120 N Manuale utente

BOCK FK

Assembly instructions

09740-01.2021-Gb

Translation of the original instructions

colour the world

of tomorrow

BOCK®

FK20/120 N FK20/145 N FK20/170 N

FK20/120 K FK20/145 K FK20/170 K

FK20/120 TK FK20/145 TK FK20/170 TK

FKX20/120 N FKX20/145 N FKX20/170 N

FKX20/120 K FKX20/145 K FKX20/170 K

FKX20/120 TK FKX20/145 TK FKX20/170 TK

09740-01.2021-DGbFITr

About these instructions

Read these instructions before assembly and before using the compressor. This will avoid

misunderstandings and prevent damage. Improper assembly and use of the compressor can lead to

serious or fatal injury.

Observe the safety instructions contained in these instructions.

These instructions must be passed onto the end customer along with the unit in which the

compressor is installed.

Bock GmbH

72636 Frickenhausen

Manufacturer

Contact

Bock GmbH

Benzstraße 7

72636 Frickenhausen

Germany

Phone +49 7022 9454-0

Fax +49 7022 9454-137

www.bock.de

[email protected]

09740-01.2021-DGbFITr

Contents Page

1 Safety 4

  1.1 Identicationofsafetyinstructions

  1.2 Qualicationsrequiredofpersonnel

1.3 General safety instructions

1.4 Intended use

2 Product description 6

2.1 Brief description

2.2 Name plate

2.3 Type key

3 Areas of application 8

3.1 Refrigerants

3.2 Oil charge

3.3 Limits of application

3.4 N and K versions

3.4.1 Limits of application R134a

3.4.2 Limits of application R407C

3.5 TK version

3.5.1 Limits of application R404A/R507

3.5.2 Limits of application R22

4Compressor assembly 9

4.1 Setting up

4.2 Maximum permissible inclination

4.3 V-belt drive

4.4 Main bearing load

4.5 Electromagnetic clutch assembly

4.6 Pipe connections

4.7 Pipes

4.8 Operating the shut-off valves

4.9 Operating mode of the lockable service connections

  4.10Suctionpipelter

5 Commissioning 13

5.1 Preparations for start-up

5.2 Pressure strength test

5.3 Leak test

5.4 Evacuation

5.5 Refrigerant charge

5.6 Shaft seal

5.6.1 Notes on replacing the shaft seal

  5.7 Avoidingliquidshocks

6 Maintenance 16

6.1 Preparation

6.2 Work to be carried out

6.3 Recommended spare parts/accessories

6.4 Extract from the lubricants table

6.5 Decommissioning

6.6 Valve plate, TK version

7 Accessories 18

7.1 Thermal protection thermostat

8 Technical Data 19

9 Dimensions and Connections 20

10 Declaration of incorporation 22

11 Service 23

09740-01.2021-DGbFITr

1.1 Identicationofsafetyinstructions:

DANGER! Indicates a dangerous situation which, if not avoided, will cause

immediate fatal or serious injury.

WARNING!

Indicates a dangerous situation which, if not avoided,

may cause fatal or serious injury.

CAUTION!

Indicates a dangerous situation which, if not

avoided, may cause fairly severe or minor injury.

ATTENTION! Indicates a situation which, if not

avoided, may cause property damage.

INFO! Important information or tips on simplifying work.

1|Safety

1.2 Qualicationsrequiredofpersonnel

WARNING! Inadequatelyqualiedpersonnelposestheriskofaccidents,

 theconsequencebeingseriousorfatalinjury.Workon

compressors is therefore reserved for personnel with the

 qualicationslistedbelow:

• For example, a refrigeration technician, refrigeration mechatronic

engineer.

As well as professions with comparable training, which enables

personnel to assemble, install, maintain and repair refrigeration and

air-conditioning systems. Personnel must be capable of assessing

the work to be carried out and recognising any potential dangers.

09740-01.2021-DGbFITr

1|Safety

These assembly instructions describe the standard version of the FK20 manufactured by Bock. The

compressor is intended for use in refrigeration systems in compliance with the limits of application.

Onlytherefrigerantspeciedintheseinstructionsmaybeused.

Any other use of the compressor is prohibited!

The Bock refrigerating compressor named in the title is intended for installation in a machine (with-

in the EU according to the EU Directives 2006/42/EC Machinery Directive, 2014/68/EU Pressure

EquipmentDirective).

Commissioning is permissible only if the compressor has been installed in accordance with these as-

sembly instructions and the entire system into which it is integrated has been inspected and approved

in accordance with legal regulations.

1.4 Intended use

1.3 General safety instructions

DANGER! • Refrigerating compressors are pressurised machines and as

such call for heightened caution and care in handling.

The maximum permissible overpressure must not be exceeded,

even for testing purposes.

WARNING! • Risk of burns! Depending on the operating conditions,

surface temperatures of over 60 °C on the discharge side or

below 0 °C on the suction side can be reached.

09740-01.2021-DGbFITr

2|Product description

Three different designs are available for various ranges of application:

> for air-conditioning the K Design

> for air-conditioning or normal cooling the N Design

> for deep freezing the TK Design

The differences lie mainly in the valve plate tooling which is adapted to each applica-

tion range where operational safety and efficiency are concerned.

Compact two-cylinder compressor in single row.

Three capacity ranges.

Lightweight aluminum design.

Lubricating oil pump with oil pressure relief valve independent of rotational direction.

Variable connection and fixing options.

Fig. 1

2.1 Brief description

Fig. 2

Suction shut-off

valve

Cylinder cover

Name plate

Shaft end

Shaft seal

Valve plate

Oil pump

Dimension and connection values can be found in Chapter 9

Discharge

shut-off valve

Sight glass

09740-01.2021-DGbFITr

2|Product description

FK 02 170 NX

1 Type designation

2 Displacement at 1450 rpm

3 LP:

Max. permissible operating pressure

  (g)Lowpressureside

HP:

Max. permissible operating pressure

  (g)Highpressureside

4 Machine number

5 Factory-lledoiltype

Fig. 3

2.2 Name plate(example)

2.3 Type key(example)

¹)K - specially for air-conditioning

N - specially for air-conditioning or normal cooling

TK - specially for deep freezing

²)X- Esteroilcharging(HFCrefrigerant,e.g.R134a,R407C)

Designs ¹)

Swept volume

Size

Ester oil charging ²)

Series

BB12345A020

19/28bar

Observe the limits of application

diagrams!

}

FKX20/170N

14,8

Bock GmbH, Benzstr. 7

72636 Frickenhausen, Germany

BOCK

09740-01.2021-DGbFITr

Max.permissibleoperatingpressure(g)high-pressureside(HP):

28 bar

3|Areas of application

ATTENTION! Compressor operation is possible within the operating limits.

These can be found in Bock compressor selection tool (VAP)

under vap.bock.de. Observe the information given there.

    -Max.permissibledischargeendtemperature:140°C

    -Max.permissibleambienttemperature:100°C

    -Max.permissibleswitchingfrequency:12x/h

    -Aminimumrunningtimeof2min.atequilibrium(continuous

operation) must be achieved.

Avoid continuous operation near the threshold. Should the

compressor happen to be used near the thresholds, we

recommend the use of a thermal protection thermostat

(Accessories, Chap. 7).

When operating in the vacuum range, there is a danger of air

entering on the suction side. This can cause chemical reactions,

a pressure rise in the condenser and an elevated compressed-

gas temperature. Prevent the ingress of air at all costs!

 Thecompressorsarefactory-lledwiththefollowingoiltype:

- for R134a, R404A/R507, R407C FUCHS Reniso Triton SE 55

- for R22 FUCHS Reniso SP 46

Compressorswithesteroilcharge(FUCHSRenisoTritonSE55)aremarkedwith anX inthe type

designation (e.g. FKX20/170N).

3.1 Refrigerants

• HFKW / HFC: R134a, R404A/R507, R407C

• (H)FCKW/(H)CFC: R22

3.2 Oil charge

3.3 Limits of application

INFO! Forrecharging,werecommendtheaboveoiltypes.Alternativesare:

see lubricants table , Chapter 6.4.

09740-01.2021-DGbFITr

4|Compressor assembly

4.1 Setting up

4.2 Maximum permissible inclination

Amax. 30°,

max. 2 minutes

amax. 15°,

continuous

operation

ATTENTION! Poor lubrication can damage the compressor.

Respect the stated values.

INFO! New compressors are factory-lled with inert gas. Leave this

service charge in the compressor for as long as possible and prevent

the ingress of air.

Check the compressor for transport damage before starting any

work.

Fig. 4

 Fittings(e.g.pipeholders,additionalunitsetc.)onthecompressorarepermissibleonly

following consultation with Bock.

 Setuponanevensurfaceorframewithsufcientload-bearingcapacity.Thecompressorcan

be fastened as follows:

- using the 4 drill holes on the baseplate

- using the 3 side M10 tapped blind holes on the left or right of the compressor housing

- using the 4 M10 tapped blind holes on the front of the compressor housing.

Correct setup of the compressor and mounting of the belt drive are decisive for running

comfort, operating safety and the service life of the compressor.

09740-01.2021-DGbFITr

4|Compressor assembly

4.3 V-belt drive

4.4 Main bearing load

4.5 Electromagnetic clutch assembly

ATTENTION! Inappropriately designed belt drives, especially belt knocking

or excessive tensioning forces can cause compressor damage!

Make sure that the drive belt is designed correctly, e.g. by using

 tensionersandselectingthebeltproleandthebeltlength.

The following description applies for an electromagnetic clutch secured to a shaft.

Toabsorbthemagneticeldoftheelectromagneticclutch,theslidingringlidhas

asnugtØ38h8(seeFig.6).

Toconnectthemagneticeld,removethemarkedAllenheadscrewsoftheslidingringlid

(seeFig.7).

Slidethemagneticeldtoasnug-tandfastenusingthethreeM5x20cheesehead

screwsprovided(Fig.7).Screwtorque=9Nm.

Further assembly of the electromagnetic clutch according to the clutch manufacturer.

Fig. 6

Sliding ring lid

Magneticeld

Fig. 7

To prevent the belt drive overloading the compressor main bearing,

ensure that:

Theengagementforceappliedbythebelttension(seeFig.5)

must not exceed Fmax per.=600N.

If the force engagement point shifts to the right (see Fig. 5,

smallpoint),theforceFmax per. reduces as per the following

formula:

Fmax per.= 30 kNmm

(50 mm + L1[mm])

Fmax= 600 N

Mbmax= 30kNmm

(mm)

Fig. 5

Snugt

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali BOCK Compressore

BOCK

BOCK BOCK HG12P Manuale utente

BOCK

BOCK UL-HGX44e Manuale utente

BOCK

BOCK FK40 Seroes Manuale utente

Manuali Compressore popolari di altre marche

Panasonic

Panasonic Matsushita QA91K22CAU6 Manuale utente

EKOM

EKOM DK50 B Manuale utente

Challenge Xtreme

Challenge Xtreme CX 1500/1 Manuale utente

Conrad

Conrad 1719346 Manuale utente

Hanbell

Hanbell RC2-AV Series Manuale utente

PLASMATECH

PLASMATECH SHARK 25 Manuale utente

Emerson

Emerson Copeland Scroll Digital HLR Series Manuale di istruzioni

Drawmer

Drawmer 1968 MKII Manuale utente

Badger Air-Brush

Badger Air-Brush X-Air 80-8 Manuale di istruzioni

Omnitronic

Omnitronic CL-166 Manuale utente

Scheppach

Scheppach HC24V Istruzioni per il montaggio

Ingersoll-Rand

Ingersoll-Rand centac C950 Manuale tecnico

LG GVH282PAB Manuale utente

Kooper

Kooper 2196438 Manuale utente

American Eagle

American Eagle SHD-66DD Manuale utente

Frick

Frick 1510 Manuale utente

Sierra

Sierra Eagle 12 VX Manuale

EUFAB

EUFAB 21083 Manuale utente