BON ELECTRONICS BSM-093N3G Manuale utente

BSM-093N3G / BSM-173N3G

BSM-183N3G / BSM-213N3G

BSM-243N3G / BSM-463N3G

BSM-553N3G

BSM-212i / BSM-242i

Contents

Safety Instructions.......................................................................................................................3

Front............................................................................................................................................4

Rear.............................................................................................................................................6

MENU Description.....................................................................................................................8

VIDE ........................................................................................................................................9

DISPLAY 1...............................................................................................................................10

DISPLAY 2...............................................................................................................................12

C L R.....................................................................................................................................14

MARKER..................................................................................................................................15

SD...........................................................................................................................................17

SD 2........................................................................................................................................19

AUDI ......................................................................................................................................20

GPI............................................................................................................................................22

SYSTEM...................................................................................................................................24

USB Firmware Update..............................................................................................................26

External Remote Control..........................................................................................................27

Assignable functions are listed below.......................................................................................28

Dimensions................................................................................................................................29

Troubleshooting........................................................................................................................30

Warranty Information................................................................................................................32

Modification of Product............................................................................................................32

Caution on Menu peration......................................................................................................32

Caution for Monitor Placement.................................................................................................32

Caution for Usage.....................................................................................................................32

Safety Instructions

To help avoid damaging your monitor, connect only one power (AC or DC) in

operation.

Rough handling of product may cause physical damage or malfunction.

Never insert anything metallic into the monitor openings. Doing so may create

the danger of electric shoc .

To avoid electric shoc , never touch the inside of the monitor. Only a qualified

should open the monitor’s case.

Openings in the monitor cabinet are provided for ventilation. To prevent

overheating, these openings should not be bloc ed or covered.

Minimum 50cm (20 inches) room to wall is necessary to prevent overheating

when the monitor is installed to wall.

Put your monitor in a location with low humidity and a minimum of dust. Avoid

places li e damp basement or dusty hallways.

Place the monitor on a solid surface and treat it carefully. The screen is made of

glass and can be damaged if dropped or sharply hit.

Do not attempt to remove the bac cover, as you will be exposed to a shoc

hazard. The bac cover should only be removed by qualified service personnel.

Unplug the monitor power before you connect external devices to the monitor.

If your monitor does not operate normally, or if there are any unusual sounds or

smells coning from it, unplug it immediately and contact us.

Please do not disassemble the monitor. No service will be provided in that case.

Displaying fixed picture for a long time may cause an afterimage or dead spots.

To recover LCD pixels, display whole white picture on screen for a n hour or

two and pixels will be recovered.

No service will be provided for user’s own color calibration.

Front

[BSM-18.5” ~ 24” Front Key]

[BSM-9” Front Key]

[BSM-46” 55” Front Key]

1) Power

2) Menu

3) Enter

4) SDI 1, SDI 2 Input

5) HDMI/DVI Input

6) Analog

Switch analog input in the order of CVBS1 -> CVBS2 -> CVBS3 -> SVIDEO ->

YPbPr -> RGB -> VGA.

7) WF/VS

Waveform / Vectorscope display selection button.

8) Marker On/Off

9) Scan

Switch scan mode among Zero Scan, Under Scan, Over Scan, Pixel to Pixel in HD

resolution. Zero Scan, Under Scan, Over Scan, Pixel to Pixel in SD resolution.

10) H/V Delay

11) R/G/B Gray

Switch for Red/Green/Blue/Gray only.

12) Function Keys

User-assigned function eys.

13) Headphone Jack

14) Speaker

15) Aspect

Adjust aspect ratio in the order of 4:3, 16:9, Fill, Native.

16) Knob for Adjustment or Enter

Knob used to adjust Brightness / Contrast / Chroma / Phase or Enter button.

BSM-463N3G,BSM-553N3G Model are Up, Down keys used by the SD MENU

display.

Rear

1,2) SDI Port

3) Component YPbPr/RGB or CVBS 1,2,3 Port

4) HDMI Port

5) DVI-I Port

6) Loop-Through Out for SDI-1/SDI-2 or YPbPr

7) AC Input

Please chec Power Cord, Power Voltage, Supply power for power input are

suitable for the standard before use.

Please do not mix AC power and DC power as it may cause the defects or fire.

⑥

①

②

③

④

⑤

⑦⑧

⑨⑩ ⑪ ⑫

8) DC Input

For DC power supply. Chec the DC Input voltage. In case of using the Battery

power, DC 12 ~ 24V is usable.

9) Update Port

The Serial communication terminal that for changing the operating

program(Firmware) of the body or controlling the monitor.

10) Remote Ethernet Port

External control via PC is able with this port by using 'Wall Control Program'.

Firmware is also updatable through this port.

11) USB Port

USB Firmware Update Port.

12) Audio IN/OUT

Audio Line In/Out Port

MENU Description

General Cautions for OSD menu or Display

The menu may not be displayed even when user pressed Menu button if there's No

Signal, or in unclear signal status.

The menu selection may be saved for each input signal mode, so sometimes user

should do menu selection again.

VIDEO

Brightness, Contrast, Chroma, Phase, Sharpness

Adjust color representation values.

SDI 3G Mode

Turns on SDI 3G mode to accept 3G signal.

SDI Switching

Normal : Use Normal in general condition but the screen might be blin ing on

screen change when you use Matrix or Routing Switcher.

Fast : Use Fast to minimize blin ing on screen change.

NTSC Setup

Select IRE among 0 or 7.5 (Default)

HDMI UV Swap

Sometimes color might be swapped on some HDMI input such as PC RGB. Turn

this mode on to return to correct color.

DISPLAY 1

Aspect

Set the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable.

1:1 Scan

Set this on to display picture in 1:1 pixel mapping.

Anamorphic

Set this mode to resize the screen to 3.56:1, 2.74:1, 2.59:1, 2.55:1, 2.40:1, 2.39:1,

2.35:1, 1.85:1, 1.75:1, 1.66:1, or 1.37:1

Waveform Display

Select waveform display mode. Choose Normal to analyze whole screen, choose

Line Select to analyze a specific line of the screen.

Waveform Line Select

Select the line when you select Line Select mode for Waveform display.

Waveform Select

Select waveform line to display among Y, Cb, Cr.

Waveform Intensity

Adjust color saturation of the waveform between 0 to 63.

Waveform & Vector Blend

Adjust transparency of the scope.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali BON ELECTRONICS Monitor

BON ELECTRONICS

BON ELECTRONICS FM-073SC Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione