3
A. General Safety Instrucons
When using this electrical appliance, basic safety precauons should always be
observed, including the following:
1. The product is for household use only.
2. Connect the appliance to single-phase AC supply of the voltage specied on
the rang label.
3. Always turn the product to the OFF posion and unplug it from the electrical
outlet when not in use.
4. Extreme cauon is necessary when the appliance is used by or near children,
invalids or elderly person.
5. Do not run cord under carpeng and do not cover cord with throw rugs, run-
ners or the like. Arrange cord away from trac area and where it will not be
tripped over.
6. Do not operate the appliance with a damaged cord or plug, or aer the unit
malfuncons, has been dropped, or damaged in any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualied person to avoid a hazard.
8. Use the appliance in a well-venlated area. While using, distance of no less
than 20cm should be kept away from wall or corner to ensure the air intakes
or exhaust openings should not be blocked unexpectedly. The unit must not be
located immediately below or besides a curtain or the likes.
9. Do not insert or allow ngers or any other objects into grill to avoid a me-
chanical danger when in use. Do not block air intakes or exhaust openings in any
manner.
10. Adequate clean water should be put into the tank within the water level limits
as shown by the water level indicator. Make sure that you DO NOT add water
whilst the power is on.
11. If you want to move the product whilst water is in the tank, unplug it and
push it slowly and very lightly on the side of the unit to avoid water spillage. The
best method would be to drain the unit using the valve at the boom of the unit.
12. Please keep the ice crystals box provided away from children, as it is a chem-
ical based substance that is harmful if swallowed. Also make sure that the ice
pack is not placed in direct sunshine. When scrapping the appliance, follow the
regulaons concerning the disposal of ice crystals.
13. Use the appliance on at, dry oor only.
14. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilies, or lack of experience and knowl-
edge, unless they have been given supervision or instrucon concerning use of
the appliance by a person responsible for their safety.
15. Children should be supervised to ensure that they do not play with the ap-
pliance.
B.Assembly of the Air Cooler
1.Remove the packaging carefully taking care not to damage the plasc body with
the scissors or knife
2.Installaon of Wheels: place 4 wheels to the holes located at the base of the air
cooler. Insert the wheels ghtly to the air cooler’s body.
3.Set the unit on a stable and horizontal base, keeping it away from radiang heat
sources and naked ame.
4. Filling Water: Turn the water tank lock to horizontal posion, taking out the
water tank, put in the ice boxes and add clean tap water to the tank. Be sure that
water level in the tank does not exceed the level “MAX” which is located at the
back of the tank.
5. Push the water tank to its housing and turn the tank lock to the vercal posi-
on.
6. Remote control: It is with CR2025 buon cell. Before use, please pull out the
card which is inserted at the buon of the remote control.
Insert plug to the electrical outlet. Turn the unit on with the power switch. Then
it will beep short, and the temperature display will show the current temperature
and the air cooler switches to the stand by posion. The funcons of the unit can
be controlled via board control panel or by remote control.
C. Operang the cooling funcon:
Turn the Change-over switch on cooling posion.
1.ON/OFF: Press the “ON/OFF” buon on the control panel or press the
ON/OFF buon on the remote control to turn the unit on. The unit will start
at low speed and normal wind. To switch back to the standby posion, sim-
ply press the ON/OFF buon on control panel or press the ON/OFF buon
on the remote control.
2. Speed: Wind speed can be adjusted to 3 levels as low---mid—high by
pressing the ‘Speed’ buon. Each me the ‘Speed’ buon is pressed, an
icon will appear on the screen indicang the current speed level.
3. Wind: Press the ‘Wind’ buon to choose the wind type. Each me this
buon is pressed, an indicator will light on the screen to indicate the type
of wind. There are 3 types of winds to choose: Normal—Natural—Sleep.
4. Timer: Press ‘Timer’ buon to set the fan running me between 0-12
hours, which switches the unit to standby aer preset me. Each me the
buon is pressed, the hours will increase one by one and the me indicator
will light on the screen.
To cancel the mer, simply press the buon unl the indicator shows”00”.
5. Swing: Press 'Swing' buon to change the wind direcon. The swing icon
will appear on the screen when the funcon is acvated. Press the buon
again to stop the oscillaon. The vercal direcon of air ow can be adjust-
ed manually by direcng the outlet louvers up and down.
6. Cooler: To acvate the air cooler funcon, please press the 'Cooler' but-
ton. Water pump will take the water from the tank and pour it onto the
cooling pad. Cooling pad absorbs the heat of the water and the evaporated
air is blown out by the help of fan. The cool breeze blown by the cooler
drops the temperature and creates a relaxing cooling eect.
Cauon: If the water level is low or there is no water in the tank, do not
acvate the ‘Cooler’ funcon. Check the water level and add water if need-
ed. Replace the stale water with fresh water. It is recommended to replace
water in the tank at least once in a week.
7.Ionizer: Press ‘Ion’ buon to acvate the ionizer funcon. Ion icon on the
screen will light and the negave anion release will start. Anions aract to
ny parcles in the air such as dust, pollen, mold spores etc. Which cause
them to become too heavy to remain air borne. This feature let us to have
dean air in the environment.
D. Operang the heang funcon:
Turn the Change-over switch on cooling posion.
1.ON/OFF: Press the “ON/OFF” buon on the control panel or press the
ON/OFF buon on the remote control to turn the unit on. The unit will
start at normal wind and low heang stage(1000W). Aer second press the
buon, heang will switch o, the fan will work 30 seconds more, then the
device will back to the standby posion.
2. Speed: this buon is not available
3. Wind/heat: Press the ‘Wind/heat’ buon to choose the heang stage.
Each me this buon is pressed, an indicator will light on the screen to
indicate the type of heang stage. There are 2 heang stages for choose:
low (1000W)—high(2000W)
4. Timer: Press ‘Timer’ buon to set the fan running me between 0-12
hours, which switches the unit to standby aer preset me. Each me the
buon is pressed, the hours will increase one by one and the me indicator
will light on the screen.
To cancel the mer, simply press the buon unl the indicator shows”00”.
