07 11
08 12
09 13
10 14
Screen: 7’’ TFT LCD screen/long life, LED backlight
Resolution: 800x480
Brightness: 450 cd/m²
Contrast: 500:1
View Angle: 140/120 degree (Horizontal/Vertical)
Antenna Connector: RP-SMA
Channel: 5.8G Input; 2 Brands/ 32 Frequency selectable (Automatically
switch to the frequency with better signal)
Size: 176x112x24mm (Height of light shield:102mm)
Battery: Built-in 4000mA Li-Po battery
DC: 12V/1A
Power Consumption: 600mA@12V(maximum)
Working Temp. : -10 - +65 degrees
Specifications
1、Install Equipment to Remote Control
2. Install Tripod Connector
a、Loosen the two nuts of remote control connector, pick it out with screw from the gap;
b、Insert the metal pole of remote control in the bottom of remote control connector case,
then put the screw back to the gap and fasten the nuts. The installation is OK;
a、After turning on the machine, set channel manually to receive image.
Corresponding channel frequency diagram are as below:
b、
By dial switch, to set the same channel or different channels for two receivers;
If setting the same channel, system will select the receiver with strong signal.
If setting different channels, you can choose the receiver by video switch button.
a、
After setting the channel of receiver, you can see the real time video image
from transmitter as below:
4、
Automatic searching Automatic searching switch
when all the switches to F8 channel, the system opens automatically searching
function. At this point, no need go through DIP switch FM, Direct operate right button
to search frequency. Press searching button once, the system will automatically
search for the best channel of the signal and lock it. May continue to operate searching
if dissatisfied.
Notice: Recommend manually dialing FM signal when the distant source signal
is weak. Automatic search frequency is not easy to lock when the signal is weak.
1、Power On/Off
2、Channel Dial
3、
Receive image
Connection Point of Holder
Tripod Connection Nut
Tripod Connector
Screw Hole
Metal Pole of
Remote Control
Remote Control Connect Nut
Remote Control
Connector Case
Slope Adjustment Nut
Sphere Connect Screw nut
12345
1 2
345
Adjust Band of A\B\E\F
Show Switch position
Band Adjustment
A
CH1
345
CH2
345
CH3
345
CH4
1
1
0
1
0
1
0
345
CH5
345
CH6
345
CH7
345
CH8
1
0
2
B
1 2
E
1 2
F
Channel Adjustment
Adjust Channel of CH1 to CH8
III、Graphic Installation
Please Note: When you adjust the revolute joints, be sure to loosen completely.
Or it will wear and tear the gear of the revolute joints.
a.Pick out the screw of holder connector, then take down connection holder of
remote controller;
b.Install the tripod connector, use tripod connection nut to connect tripod holder directly.
3. Install Antenna
a. Directional or Omnidirectional antenna which match with RP-SMA can be installed;
IV、Operation
a、After completing the operation above, open the light shield, push the power button to
ON to turn on the machine, the screen will be lighted; Push the power button to OFF to
turn off the machine and the screen.
b、When the power is not sufficient, power indicator will blink and you will hear a
warning voice; If no manual Shutdown, system will turn off the machine automatically.
Notice: If you do not use the machine for long time, please charge the
battery regularly to avoid undue discharging and cause the battery damage.
5、
Charging for the host
3S\4S\5S\6S
Battery
charger
12V
Charge Schematic
Charging Cable
host
a、
When the host battery runs low, a voice prompt, and then automatically shut
down; please charge in time for the host.
345
1
0
1 2 345
1 2
