Bosch BE 300 LSN Manuale utente

Installation Instructions

BE 300 LSN

- 1 - 610-4.998.101.907

A3 Sept. 2001

Installation procedure and technical data

Cable routing:

1. The data cables are strain-relieved and

stripped directly after entering the cable

entry point.

Strip the cables to the required length (up

to the marked area (1) + approx. 10 cm)).

2. Very important: Pull insulating sheathing

over the auxiliary shielding wires.

3. Route the cable wires together with the

auxiliary shielding wire in the direction of

the marked area (1) (see next page for

maintenance position). 1

Slot Slot

Remove the top of the casing:

1. Press a screwdriver into the slots in the

bottom of the casing in order to raise the top

of the casing slightly.

2. Swing the bottom part of the top of the

casing approx. 45° relative to the bottom of

the casing. Pull off the top part to the front.

Fitting the bottom of the casing:

1. Cable entry points for recessed

cabling (1).

2. Cable entry points for surface-

routed cabling (2).

3. Cable entry point if the unit is

fitted over a recessed socket (3).

4. Recommended bolts 2x for 4x40

installation.

1 1

2 2

3 1

Continued on page 2

Installation Instructions

BE 300 LSN

- 2 - 610-4.998.101.907

A3 Sept. 2001

Insert top of casing into maintenance position:

1. A retaining clip is located at the lower

left side of the bottom of the casing

for holding the top of the casing in

the maintenance position.

2. Hook the top of the casing into

the retaining clip from the side.

Connect data cable:

1. Solder the cable wires and auxiliary shielding wires onto the connectors.

2. Route the cable wires so as not to impair the correct functioning of the pcb

(e.g. tamper switch).

LSN1

GND

LSN2

Fit the top of the casing:

1. Remove the top of the casing from the maintenance position and fit it into the

top of the bottom section at an angle of approx. 45°.

2. Swing the top section of the casing downwards and press it firmly until it snaps

into the bottom section.

Continued on page 3

Installation Instructions

BE 300 LSN

- 3 - 610-4.998.101.907

A3 Sept. 2001

Technical data

Operating voltage

- LSN section

- Control section + 15 V ... + 31 V

+ 9.6 V ... + 30 V

Current consumption

- LSN section

- Control section max. 3,55 mA (typ. 2,9 mA)

20 mA standby / 50 mA with illumination

Tamper monitoring Tamper switch

Ambient conditions

- Operating temperature

- Storage temperature

- Degree of protection of casing

- 5° C ... + 45° C

- 20° C... + 60° C

IP 40

Casing

- Material

- Colour ABS

RAL 9010

Dimensions (H x W x D) 112 x 162 x 29 mm

Weight 0.25 kg

VdS class Class C

VdS approval G 100070

(included in NZ 300 LSN approval)

Sealing the unit:

1. Twist a locking screw

(contained in the accessories pack)

from below into the casing.

2. Seal the screw. Locking screw and seal

Attach service card:

1. Swing down the control console flap of the BE 300 LSN.

2. Stick the service card with the telephone No. of the service centre and ID

number onto the inside of the flap.

Altri manuali per BE 300 LSN

Altri manuali Bosch Pannello di controllo

Bosch

Bosch AMAX panel 2100 Manuale utente

Bosch

Bosch B6512 Manuale utente

Bosch

Bosch FPD-7024 Guida rapida

Bosch

Bosch D7212GV3 Guida rapida

Bosch

Bosch AMAX panel 2000 ICP-AMAX-P Manuale utente

Bosch

Bosch Solution Ultima 880 Manuale utente

Bosch

Bosch D6412 Guida rapida

Bosch

Bosch MAP Control Center IUI-MAP0001-2 Manuale utente

Bosch

Bosch ICP-AMAX4-P1 Manuale utente

Bosch

Bosch 2000 Series Guida alla risoluzione dei problemi

Bosch

Bosch ICP-EZM2 Manuale utente

Bosch

Bosch HPC 400 Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Bosch

Bosch B9512G Manuale utente

Bosch

Bosch ICP-CC488 Manuale utente

Bosch

Bosch DS9400 Series Come usare

Bosch

Bosch D9112B Guida alla risoluzione dei problemi

Bosch

Bosch D9412GV2 Manuale utente

Bosch

Bosch B6512 Manuale di istruzioni

Bosch

Bosch ICP-CC488 Manuale utente

Bosch

Bosch Rexroth VAM 10.2 Manuale tecnico

Bosch

Bosch ICP-CC408 Manuale utente

Bosch

Bosch D9412GV2 Manuale utente

Bosch

Bosch FPA-5000 Guida utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche

Truma

Truma CP plus Manuale utente