Bosch 560 DDC Manuale utente
Quick Start Guide
560/583 DDC
Please refer to the included Hardware User’s Guide and BACview Installation and
Operation Manual for more detailed information on setting up and using the controllers.
8733914716(2014/02)
2 |
8733914716 DDC (2014/02) Subject to change without prior notice Quick Start Guide
Quick Start Guide
| 3
Quick Start Guide Subject to change without prior notice 8733914716 DDC (2014/02)
Quick Start Guide
CONTENTS
Quick Start Guide – Hardware Setup .................4
Controller Features.............................4
Getting Started...................................5
Jumper Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP Switch Settings ...............................6
Rotary Dial Settings...............................7
Power Up .......................................7
Quick Start Guide – Software Setup..................8
Software Conguration Tools ....................8
Handheld BACview Module Features ..............8
Virtual BACview Module Features .................9
Getting Connected...............................10
Conguring Application Parameters using BACview...11
Modifying Parameter Values Using BACview .........11
Customizing Program Features Using BACview ......12
Useful Shortcuts for Tweaking Program Features
Using BACview...............................12
Congurable I/O Port Assignments (SW 7.03.06) ......13
Wiring Diagram .................................14
Typical FHP560 Wiring Diagram ...................14
Table of Contents
4 |
8733914716 DDC (2014/02) Subject to change without prior notice Quick Start Guide
Quick Start Guide
©Copyright 2014 Bosch, Inc All rights reserved
Quick Start Guide – Hardware Setup
Controller Features
Battery
Network
LON Connector
Rotary Switch
Jumper Bank
RNET
Connector
Universal
Inputs
IN-1 to IN-6
Local Access Port
(see page 10)
24VAC
DIP Switch
Bank
Analog
Outputs
(583 only)
Digital
Outputs
Part Number
Hardware Setup
FHP 560 Controller
| 5
Quick Start Guide Subject to change without prior notice 8733914716 DDC (2014/02)
Quick Start Guide
GETTING STARTED
Perform a quick visual inspection to ensure the
controller has no external damage and all connectors
are intact. Ensure wiring is per desired application
(see sample FHP 560 wiring diagram on page 14).
Refer to I/O port conguration (page 13) for further
details on wiring inputs and outputs.
JUMPER SETTINGS
Verify that hardware conguration for jumpers
match corresponding Heat Pump system
application. If the controller is networked, ensure
communications jumper is set to EIA-485, unless
the network protocol is BACnet over ARC156.
Getting Started
Input Selection Jumpers for IN-1 & IN-2
(e.g. for a 0-5V CO2 Sensor
connected to IN-1, the jumper
should be set in bottom position)
IN-1 & IN-2 Jumper
Settings Label
Communications Selection Jumper
(i.e. jumper in bottom position for
BACnet over ARC156, or, jumper in top
position for EIA-485 using BACnet over
MS/TP, LON, Modbus, or N2 protocols)
Communications Selection label
In the above diagram, IN-1 and IN-2 are set to Thermistor/Dry
Contact, and Communications is set to BACnet over ARC156.
6 |
8733914716 DDC (2014/02) Subject to change without prior notice Quick Start Guide
Quick Start Guide
DIP SWITCH SETTINGS
Verify that hardware conguration for DIP switches
match corresponding network application per the
BAS Port Settings.
BAUD RATES SW1 SW2
9600 Off Off
19.2K Off On
38.4K On Off
76.8K On On
PROTOCOLS SW3 SW4
BACnet® MS/TP Off Off
N2 On Off
Modbus Off On
LON Option On On
Sample DIP switch settings for a
LON Talk Application.
Caution
The LonTalk®card
must be installed
DIP Switch Settings
DIP
Switch
| 7
Quick Start Guide Subject to change without prior notice 8733914716 DDC (2014/02)
Quick Start Guide
ROTARY DIAL SETTINGS
Verify hardware conguration for rotary dials matches
corresponding application.
The rotary dials provide the controller address for
identication over a network.
The top dial represents the tens digit of the address,
and the bottom dial represents the ones digit for the
address. See example below:
In the example to the left,
the rotary dial is set to 69.
Rotary Dial Settings
POWER UP
Apply power to the unit and verify via the power LED
that the controller is receiving 24VAC.
8 |
8733914716 DDC (2014/02) Subject to change without prior notice Quick Start Guide
Quick Start Guide
Quick Start Guide – Software Setup
Software Conguration Tools
Handheld BACview Module Features
• Hot-keys: used for entering number values.
• Arrow keys: used for navigating the various
BACview screens.
• Soft- keys: four (4) buttons used to access
corresponding Soft-key Labels directly above them.
Software Setup
• Link: an arrow next to a menu item implies
additional screen(s) can be accessed through
that menu. To access a screen navigate to the
menu item and hit the ENTER button. (Note:
selected elds have a bracket [...] around them).
• Contrast screw: used to adjust screen contrast.
| 9
Quick Start Guide Subject to change without prior notice 8733914716 DDC (2014/02)
Quick Start Guide
Virtual BACview Features
Installation
• Download and install driver for USB cable (cable p/n
641-261 purchase required) from FHP website
(http://fhp-mfg.com/?p=controls_support).
• Verify device is installed in Device Manager and take
note of COM port.
• Download and install Virtual BACview from FHP
website (http://fhp-mfg.com/?p=controls_support).
Interface
• Use mouse to select keypad buttons (for
shortcut key combinations, FN = Ctrl on
keyboard e.g. FN+9 is Ctrl+9).
• Screen size (number of rows) can be adjusted
in Virtual BACview at startup.
Caution
All screen shots of BACview used in
this manual are from Virtual BACview
and may not represent the screen
viewed on an actual BACview module,
which is limited to four (4) rows of text.
Virtual BACview Features
10 |
8733914716 DDC (2014/02) Subject to change without prior notice Quick Start Guide
Quick Start Guide
Getting connected
Getting Connected
Connect the BACview module (or laptop if using
Virtual BACview) to the FHP controller, or to an RS
Sensor connected to the controller.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Bosch Controllori
Bosch
Bosch CC 100 M Manuale utente
Bosch
Bosch Rexroth IndraDrive M Manuale tecnico
Bosch
Bosch ARC R-1 Istruzioni operative
Bosch
Bosch Smart Home controller II Manuale dell'operatore
Bosch
Bosch Smart Home Controller AA Manuale utente
Bosch
Bosch CR 20 RF Manuale utente
Bosch
Bosch FMR-7033 Manuale utente
Bosch
Bosch Rexroth VT-VPCD Series Manuale utente
Bosch
Bosch CR 400 Manuale utente
Bosch
Bosch PVA-4CR12 Manuale utente
Bosch
Bosch Rexroth IndraDrive CsDrive System with HCS01 Manuale utente
Bosch
Bosch Access Easy Controller 2.1 Istruzioni per il montaggio
Bosch
Bosch ADS-AMC2-4R4CF Manuale utente
Bosch
Bosch Rexroth CS 106 Guida utente
Bosch
Bosch CLIMATE 5000 VRF RDCI Series Manuale di istruzioni
Bosch
Bosch Rexroth CKL Series Guida
Bosch
Bosch Rexroth CS 440RC Guida utente
Bosch
Bosch BODAS RC/3 Series Manuale utente
Bosch
Bosch Rexroth 31 Series Manuale di istruzioni
Bosch
Bosch DSA E Series Manuale utente
