Bosch AEC-AMC2-VDS1 Manuale utente

AEC-AMC2-VDS1

en Installation manual

de Installationshandbuch

pl Instrukcja instalacji

zh 安装指南

nl Installatiehandleiding

ru Руководство по установке

hu Telepítői kézikönyv

pt Manual de instalação

es Manual de instalación

AEC-AMC2-VDS1 3

Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12

English

Deutsch

Polski

中文

Nederlands

Magyar

Português brasileiro

Español latinoamericano

AEC-AMC2-VDS1 - Installation manual en 5

Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12

Included parts

The metal housing inlcudes the following components:

Figure 1 Parts of the housing

1 = Name plate

2 = AMC grounding post

3 = Mounting rail for PS and AMC

4 = Cable knock-out for reader and signal cables

5 = Opening for rechargeable battery securation

6 = Cover tamper switch

7 = Power cable knock-out

8 = Label

9 = Three pin connector

10 = Cover grounding post

11 = Main grounding post

12 = Power supply connector

6en AEC-AMC2-VDS1 - Installation manual

F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH

The accessories kit includes the following cables. Install these

cables as described in Section Connection of the Devices,

page 8.

Figure 2 Accessories kit content

Content of the accessories kit:

A= Pre-assembled cable to connect the AMC to the power

supply

B= Pre-assembled cable to connect the rechargeable batteries

to the UPS (uninterruptable power supply) which is included in

the power supply

C= Cable using 24 V mode

D= Grounding cable for the cover

E= Cable ties to secure the pre-assembled cable

F= Cable ties to fix the rechargeable batteries

G= Pre-assembled cable with temperature sensor

H= Three screw anchors S8 and wood screws M6 x 50

J= Bracket for cable fixing

Before the assembly of the housing the following preparations

should be done and conditions be considered.

AEC-AMC2-VDS1 - Installation manual en 7

Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12

The opening for the AC supply cable (position 7) is covered by

two plastic inserts. The AC cable can either be routed through a

standard cable duct (40 mm x 25 mm) or be introduced directly

from the back of the housing. Disrupt the appropriate plastic

insert such that you can insert the power cable properly.

Mounting the Housing

Open the housing cover lock with the provided key and remove

the hood from the wall mounted frame.

Mount the metal housing at the desired position with the screw

anchors provided with the enclosure.

Use the screws (position Hof the accessories kit) at the points

to mount the housing against the wall.

Figure 3 Demensions of the housing

8en AEC-AMC2-VDS1 - Installation manual

F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH

Connection of the Devices

Figure 4 Connection of the devices

1. Mount the AMC on the rail (item 3 in Figure 1) and left

aside the power supply.

2. Put the rechargeable batteries on the bottom of the

housing and secure them with the cable ties F - (Figure 2).

3. Stick the bracket J Figure 2 on the back of the housing in

such a way that later on not used connectors of the cable

Bcan fixed with it.

4. Cable set A:

a. Connect the 7-pin plug A1 to the AMC’s power supply

connector (labeled: POWER).

b. Attach connectors A3 to the PS-interface DC and A2

to the interface labeled OK.

c. Connect the grounding cable A4 beneath the

grounding point 2.

5. Cable set B:

NOTICE!

The following steps describe connecting the rechargeable

batteries in 24 V mode. For information on 12 V mode

connections, refer to Section 12 V Mode Variations, page 11.

AEC-AMC2-VDS1 - Installation manual en 9

Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12

a. Connect the plug connector B1 the second position

from the left on the power supply - labeled with BAT.

b. Attach connector B2b (red) to the +-pin of the first

rechargeable battery.

c. With cable Cconnect the --pin of the first

rechargeable battery to the +-pin of the second

rechargeable battery.

d. Attach connector B2a (black) to the --pin of the

second rechargeable battery.

e. Connectors B3a and B3b are not used.

6. Cable set G:

a. Attach connector G1 on the PS-interface labbeled

RTH.

b. Route the cable across the temperature sensor

bracket Jso that the temperature sensor G2 hangs

approximitely 5 cm (2 in.) above the rechargeable

batteries.

7. Pre-assembled cable set 12:

a. Connect the 2-pin plug on the interface AC of the

power supply.

8. Pre-assembled cable 6:

a. Connect the loose ends of the cover tamper switch to

the 2-pin screw connector on the top of the AMC.

Position the cable in the space between the housing

and the mounting rail.

9. Connect the main AC supply X:

a. Connect the brown (phase) wire to terminal L1.

b. Connect the blue (neutral) wire to terminal N.

c. Connect the grounding cable to the housing at

position 11.

DANGER!

Remove the fuse from the three-pin connector before

proceeding with the power supply connection.

Do not install the fuse before completing the installation

procedure.

CAUTION!

Shorten the external supply wires so that the ground (yellow/

green) wire is at least 20 mm (0.8 in.) longer than the live (blue

and brown) wires. This ensures that the ground wire cannot be

accidentally disconnected before life wires.

10 en AEC-AMC2-VDS1 - Installation manual

F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH

10. Cable D:

a. Connect D1 to grounding post 10.

b. Connect D2 to the grounding post on the cover.

11. Install the fuse.

12. Close the cover.

NOTICE!

Connect the readers and other peripheral devices as described

in the AMC Installation Manuals. Route the device cables

through the knock-outs in the top an right side wall of the

housing, or through the rear of the housing.

Indice

Lingue:

Altri manuali Bosch Controllori

Bosch

Bosch BMS-BAC Manuale utente

Bosch

Bosch Smart Home controller II Manuale dell'operatore

Bosch

Bosch Rexroth IndraDrive HMS02 Manuale utente

Bosch

Bosch PVA-4CR12 Manuale utente

Bosch

Bosch WORCESTER GREENSTAR WIRING CENTRE Guida utente

Bosch

Bosch REXROTH SB356 Manuale utente

Bosch

Bosch AMC-4W Manuale utente

Bosch

Bosch Rexroth OptiFeed-FS EcoDrive 03 FLP04VRS Istruzioni per l'uso e l'installazione

Bosch

Bosch Rexroth 31 Series Manuale di istruzioni

Bosch

Bosch Rexroth Rho 4.0 Manuale utente

Bosch

Bosch ADS-AMC2-4R4CF Manuale utente

Bosch

Bosch Rexroth IndraDrive M Manuale tecnico

Bosch

Bosch Access Easy Controller 2.1 Istruzioni per il montaggio

Bosch

Bosch Rexroth CS 440RC Guida utente

Bosch

Bosch Rexroth IndraControl L25 Manuale utente

Bosch

Bosch Rexroth CS660 Manuale utente

Bosch

Bosch GAL 18V-160 C Professional Manuale utente

Bosch

Bosch K 30 RF Manuale utente

Bosch

Bosch 560 DDC Manuale utente

Bosch

Bosch rexroth CS610 Manuale utente

Bosch

Bosch Rexroth Diax 04 Manuale utente

Bosch

Bosch EasyControl CT200B Manuale utente

Bosch

Bosch LTC 8600 Manuale utente

Bosch

Bosch AMC2 Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente