Bosch IUI-UEZ-BE1000s Manuale utente

IUI-UEZ-BE1000s Intrusion Keypad

Manuel d'utilisation

IUI-UEZ-BE1000s

Intrusion

Gebruiksaanwijzing

IUI-UEZ-BE1000s

Inbraakdetectie

Operating manual

IUI-UEZ-BE1000s

Intrusion

Bedienungsanleitung

IUI-UEZ-BE1000s

Notruf

- 2 -

Introduction and safety instructions..............3

Display/control elements

Explanation of message display ........................4

Explanation of keys............................................5

Message display/processing ..........................6

Querying statuses

Querying areas and triggering statuses.............7

Querying internal program statuses...................8

Time-controlled activation

Time-controlled arming ......................................9

Time-controlled disarming................................10

Code mode

Starting and ending code mode.......................11

Starting and ending code mode with

messages present............................................12

Operation in the menu

Calling up and ending functions.......................13

Switching internal programs on and off............14

Resetting the control panel..............................15

Resetting internal messages............................15

Display test ......................................................16

Querying areas and ignoring

detector zones and faults.................................17

Isolating detector zones...................................18

Isolating a detector in a detector zone.............19

Walktest...........................................................20

Notes ..............................................................21

Table of Contents

- 3 -

Introduction to operation

The remote keypad can only be operated by

trained personnel.

For safety reasons and to prevent faulty op-

eration, the authorization code for operating

the system should only be provided to these

people.

Under certain conditions, the keypad is inac-

tive, i.e. inoperable

Detection area is armed. The keypad has

been allocated to the armed detection area.

Detection area is armed. The keypad has

been programmed to "dark when armed".

Holdup alarm in the system. The keypad

has been programmed to "dark if holdup".

What will this operating manual tell you

This manual contains all information required

for interpreting the message display and op-

erating the keypad.

What this operating manual will not tell

you

The operating manual does do not provide

any information regarding general or special-

ized technical/safety knowledge.

Therefore: Please ensure that you are famil-

iar with all safety/technical procedures and

guidelines in your area (e.g. what to do in the

event of an alarm, application plans, alarm

organization, etc.).

Notes regarding cleaning

When cleaning the surface of the keypad,

particularly the user interface and display

unit, ensure that no corrosive or abrasive

cleansers are used and that no fluid pene-

trates into the inside of the unit.

Introduction and safet

instructions

- 4 -

Explanation of message display

Display for operation (green LED).

The display lights up when the unit is

ready for operation.

Cumulative display for alarms (red LED).

The display lights up in the event of an ex-

ternal or internal alarm, a pre-alarm, or a

fault with external alarm signaling.

The corresponding alarm is saved and in-

dicated by the buzzer.

General display for faults (yellow LED).

The display lights up for all types of faults.

The corresponding fault message is saved

and indicated by the buzzer. If the type of

fault cannot be reset by the authorized

user, 24-hour service must be informed.

Display (LCD): The display consists of

2 lines with 16 characters. All pending mes-

sages as well as the notes for operation are

displayed in the menu in plain text. If the key-

pad is in standby mode, i.e. there are no

messages and no functions have been called

up from the menu, then the current time, the

date, as well as access via the center vari-

able function key in the menu will appear.

Display/control elements

pNumber of the current message

qType of message

rDetector zone number

sDetector number of the detector zone

3 HO UP 0012-6

MESSAGE? DETEC.

pq r s

nNumber of messages

oType of message

03 HOLD UP

n o

15 : 13 22.11.2005

987

654

21 3

G H ID E F

B C

P Q RM N OJ K L

S T U Y Z

ENTER

./:

STOP

V W X

- 5 -

Explanation of keys

Variable function keys

The variable function keys can be

used to call up the functions dis-

played via these keys. The text

that appears above the key in the

display provides information for

operating the corresponding vari-

able function key; for example:

- The left variable key calls up the next mes-

sage.

- The center variable key displays the help

text for 3 seconds.

- The right variable key calls up the next de-

tector of the detector zone.

Information regarding the variable function

keys for operating the functions in the menu:

Scroll forward through the functions in

the menu using the right variable function

key.

Scroll backwards through the functions

in the menu using the left variable function

key.

Function keys

Enter digits:

If number entries are required (e.g. inputting

the operator code), these entries can be

made at the position where the cursor is lo-

cated.

Confirm input:

Press the "ENTER" key:

- After inputting the digits.

- To call up the functions in the menu.

Return / Stop:

The "STOP" key causes a return by one level

or cancellation of the function started.

Switch off buzzer:

The buzzer will sound in the event of alarm or

fault messages. The buzzer can be switched

off using the "Buzzer off" key.

.................................

Display/control elements

)Variable function keys

3 HO UP 0012-6

MESSAGE ? DETEC

Display

ENTER

STOP

A B C

Important

info

- 6 -

Description

Example: there are a total of 3 messages (de-

tector zones) pending that are message type

e.g. "INTRUSION". If multiple message types

are pending, they are displayed according to

their priority.

Procedure

1.Call up the next message type. Press the

right key.

The right key can be used to call up

additional message types (e.g. "FAULT").

2.Call up the message for the message type

selected. Press the "ENTER" key.

The chronologically first message (1) will

be displayed along with the detector zone

(no. 0001) and the detector (no. 02).

3.Call up additional messages. Press the left

key.

The messages (detector zones) for the

message type selected can be called up

with the left key. The messages are

displayed consecutively according to their

chronological order e.g. detector zone

(no. 0033) along with the detector (no. 07).

4.Call up additional detectors. Press the right

key.

The next triggered detector (no. 14) in the

detector zone (no. 0033) will be displayed

in the first line.

5.Call up additional information. Press the

center key.

The additional information (e.g. staircase)

will be displayed in plain text for approxi-

mately 3 seconds. For units networked us-

ing SRT, the unit number is displayed for

an additional 3 seconds. The display then

returns to the previous display.

1 FAULT 0001-02

STAIRCASE

2 FAULT 0033-14

MESSAGE ? DETEC

03 INTRUS. EXT

2 FAULT 0033-07

MESSAGE ? DETEC

02 FAULT

1 FAULT 0001-02

MESSAGE ? DETEC

Message display/processing

- 7 -

Querying areas and triggering

statuses

Description

The status of ON/OFF areas (armed/dis-

armed) and their triggering of detectors can

be displayed on the display. For example, in

order to properly arm the system, all doors

and windows must be in normal condition

(closed). This function can be used, for ex-

ample, to locate corresponding detectors and

detector zones in the system. Example – dis-

play:

Procedure

1.Start a query. Press the center

"menu" key.

The query display will appear.

2.Call up areas. Press the left key.

The first area and its status will be dis-

played.

3.Call up additional areas. Press the right

key.

The right key can be used to call up

additional areas consecutively. After the

last area, "AREA 01" reappears in the dis-

play. If the area is not ready for arming,

"NARM" (reasons for "not ready for arm-

ing") appears in the display.

4.Call up an area's triggering. Press the cen-

ter key.

The reasons for "not ready for arming" will

be displayed.

5.Call up an area's additional triggering.

Press the right key.

The right key can be used to call up

the area's additional triggering consecu-

tively. After the last triggering, the first trig-

gering reappears in the display.

6.Call up additional information. Press the

center key.

Additional information for the triggering will

be displayed for approximately 3 seconds.

7.Return. Press the "STOP" key twice.

The "STOP" key causes a return by one

level. The query will be ended.

15 : 13 22.11.2005

ID:0 CO:¾¾¾¾¾¾

REA PROG.

0005 - 13 = TRIGGE

Window room 6

0005 - 17 = TRIGGE

0005 - 13 = TRIGGE

AREA 01 = OFF

NARM

ID:0 CO:¾¾¾¾¾¾

AREA PROG.

AREA 02 = OFF

NARM

Querying statuses

- 8 -

Querying internal program statuses

Description

Example – display:

Procedure

1.Start a query. Press the center

"menu" key.

The query for the internal program will be

started and displayed.

2.Call up internal programs. Press the right

key.

The first internal program and its status

(ON/OFF) will be displayed

3.Call up additional internal programs. Press

the right key.

By pressing the right key, additional

internal programs can be called up con-

secutively. The status of internal program

02 (ON/OFF) will be displayed. After the

last internal program and pressing the right

key, internal program 1 reappears in

the display.

4.End the query. Press the "STOP" key

This action ends the query. If you press the

"STOP" key is again, the standby picture

will appear in the display.

15 : 13 22.11.2005

MENU ID:0 CO:¾¾¾¾¾¾

REA PROG.

INT-PR 01 = ON

ID:0 CO:¾¾¾¾¾¾

AREA PROG.

INT-PR 02 = ON

Querying statuses

- 9 -

Time-controlled arming

Description

The exit delay time must be entered by the

safety company in charge. Not in compliance

with VdS.

There are ______ seconds available for exit-

ing the premises before the system is armed.

Procedure

1.Call up the input field for time-controlled

arming. Press the center key.

The input field for the time-controlled arm-

ing code will be displayed.

2.Start time-controlled arming.

Enter ID (1 to 3 digits) for ID 7, e.g. enter

007. Enter code (0 to 6 digits), e.g. 123123;

time-controlled arming starts automatically

after entry of the digits. Only press the

"ENTER" key if the code is < 6 digits.

3.Time-controlled arming is activated.

The delay time has started. The buzzer will

sound during the exit delay time. The room

must be exited within the programmed time

of ... seconds.

The left key can be used to cancel the

arming procedure if needed.

4.Time-controlled arming is active.

After the door is closed, the system is

armed, which is indicated by a buzzer

sound of 3 seconds. The following mes-

sage will appear on the display.

15 : 13 22.11.2005

AREA

RMED

ID: 007 CO:_ _ _ _ _ _

AREA PROG.

ID:0 CO:¾¾¾¾¾¾

AREA PROG.

ARMED IN . . . . . s

CANCEL

Time-controlled activation

- 10 -

Time-controlled disarming

Description

The entry delay time must be entered by the

safety company in charge. Not in compliance

with VdS.

There are ______ seconds available to enter

the premises and disarm the system.

Procedure

1.The buzzer sounds when the door group is

triggered.

2.Call up the input field for time-controlled

disarming. Press the "menu" key.

The input field for the time-controlled dis-

arming code will be displayed.

3.Enter the time-controlled disarming code.

Enter ID (1 to 3 digits) for ID 7, e.g. en-

ter 007. Enter code (0 to 6 digits), e.g.

123123; time-controlled disarming starts

automatically after entry of the six digits.

Only press the "ENTER" key if the code is

< 6 digits. There are .... seconds available.

4.Time-controlled disarming has been exe-

cuted.

After successfully disarming, the message

"AREA DISARMED" will appear in the dis-

play.

ID:0 CO:¾¾¾¾¾¾

ID: 007 CO:_ _ _ _ _ _

15 : 13 22.11.2005

AREA

DISARMED

Time-controlled activation

Indice

Lingue:

Altri manuali Bosch Tastiera

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo