Bosch TouchOne Manuale utente
TouchOne
User’s Guide
32
Contents
1 Introduction 1
1.1 Product Summary 1
1.2 Version 1
1.3 Features not covered
1
2 General Usage 2
2.1 Home Screen 2
2.2 Keypad Screen 3
2.3 Arming the System 4
2.3.1 Arming in AWAY Mode 4
2.3.2 Arming in STAY Mode 5
2.3.3 Arming in STAY Mode 2 7
2.3.4 Disarming the System
9
3 Zones 10
3.1 Isolating Zones 10
3.2 Renaming Zones 11
14
4 Users 12
4.1 Adding a User 12
4.2 Deleting a User 13
4.3 Renaming a User 13
4.4 Adding / Changing a User Photo 14
4.5 Editing a User PIN 15
4.6 Adding a Mobile Device 16
4.7 Removing a Mobile Device 17
4.8 Adding an RF Keyfob 17
4.9 Deleting an RF Keyfob 18
5 Outputs 18
5.1 Controlling Outputs 19
5.2 Renaming Outputs 19
6 Date and Time 20
6.1 Change the System Date and Time 20
7 WiFi 20
7.1 Connect the TouchOne to a WiFi network 21
7.2 Disconnect from a WiFi network 22
8 Display, Wallpaper & Sounds 22
8.1 Change the TouchOne Volume 21
8.2 Change the TouchOne Brightness 23
8.3 Change the Wallpaper 23
8.4 Standby Screen 24
8.4.1 Make the Screen sleep during Standby. 24
8.4.2 Show a Photo Slideshow during Standby. 25
8.4.3 Change the Standby Time 26
8.4.4 Enable Standby when the system is armed in AWAY Mode 26
8.4.5 Show the Alarm Status on the Standby Screen. 27
9 Language 28
9.1 Change the TouchOne Language 28
10 Tutorials 30
10.1 Viewing a Tutorial Video 30
32
1. Introduction
1.1.Product Summary
The TouchOne is a High Denition 7”Touchscreen keypad for Bosch Control
Panels that provides a rich user interface and extended functionality.
1.2 Version
This User Guide has been written for TouchOne Software Version 2.2. Please contact
your installer for a revised User Guide should the options shown in this document
differ from what is on your touchscreen.
1.3 Features not covered
The TouchOne provides a graphical interface to the major functions of the system.
Other less common features are accessed using the Keypad screen in the same way
in which you would interact with a Bosch TEXT LCD Codepad. As the interface is the
same, please refer to the “Operation with TEXT LCD Codepad” section in the Control
Panel User Guide for operating instructions of the features listed below:
• Forced Arming
• Programming STAY Mode 2 Zones
• Reset Latching Outputs
• Telco Arm/Disarm Sequence
• Testing
• General Usage
2.1 Home Screen
Figure 1 shows the TouchOne Home
Screen. This screen allows you to view
critical status information of the system
and perform common actions:
2.2 Keypad Screen
Figure 2 shows the TouchOne Keypad
Screen. This allows you to perform
system functions that do not have a
graphical interface on the TouchOne.
Please refer to the “Operation with
TEXT LCD Codepad” section in
the Control Panel User Guide for
instructions on performing these
functions on this screen. Figure 1: Home Screen
54
2.3 Arming the System
2.3.1 Arming in AWAY Mode
When you leave your premises and
require all zones to be in a ready
state to detect intrusion, arm the
system in AWAY Mode. There are
two different methods for arming
the system in AWAY Mode. Method
one is optional and can be disabled
by your installer if you do not
want to use single button arming.
Method two is standard and always
operates.
Method One (Quick Arm) 1. From the Home Screen, touch the Arm Area button.
Two beeps will sound and the Area Status Card changes.
Note: if you have multiple areas enabled, you will need to enter
your user code. If your user code has authority for both areas,
both areas will arm.
Method Two 1. From the Home Screen, touch and drag the Area
Status Box you want to arm.
2. Drag the Area Status Box into the Away Arm circle.
3. Enter your user code.
Two beeps will sound and the Area Status Card changes.
Method Three 1. Touch the Keypad button to show the Keypad
screen.
2. Enter your user code followed by the [#] button (for
example, [2580 #]).
Two beeps will sound and the Area Status Card changes.
Figure 2: Keypad Screen
76
2.3.2 Arming in STAY Mode 1
STAY Mode 1 is only used when the perimeter and unused areas of the premises
need to be armed to detect an intruder from entering the premises. At the same time,
you can move freely within an area that is automatically isolated. Only your installer
can program zones automatically isolated in STAY Mode 1. There are two different
methods for arming the system in STAY Mode 1. Method one is standard and always
operates. Method two is optional and may be disabled by your installer if you do not
want to use single button arming.
Entry Guard Timer for STAY Mode 1
When arming the system in STAY Mode 1, an optional entry timer called Entry Guard
Time for STAY Mode is available. Use this entry timer to delay the sirens if a zone is not
automatically isolated and activates an alarm condition.
Entry Guard Time for STAY Mode is the delay time used for all zones except 24-hour
zones when the system is armed in STAY Mode 1 or STAY Mode 2.
If the Entry Guard Time for STAY Mode is programmed and a zone that was not
automatically isolated is activated, the TouchOne beeps twice per second until the
entry timer expires or the system is disarmed. If the alarm condition is not reset by
entering your user code (such as [2580]) before the entry time expires, the sirens
activate into alarm. Only your installer can program this feature.
Method One 1. Touch the Keypad button to show the Keypad
screen.
2. Enter your user code followed by the [*] button (for
example, [2580 *]).
Two beeps will sound and the Area Status Card changes.
Method Two 1. From the Home Screen, touch and drag the Area
Status Box you want to arm.
2. Drag the Area Status Box into the Stay Arm circle.
3. Enter your user code.
Two beeps will sound and the Area Status Card changes.
2.3.3 Arming in STAY Mode 2
STAY Mode 2 is only used when the perimeter and unused areas of the premises
need to be armed to detect an intruder from entering the premises, at the same time
allowing you to move freely within an area that is automatically isolated. Any Master
Code or Installer Code user can program zones to be automatically isolated in STAY
Mode 2.
98
Entry Guard Timer for STAY Mode 2
When arming the system in STAY Mode 2, an optional entry timer called Entry Guard
Time for STAY Mode is available. Use this entry timer to delay the sirens if a zone is
not automatically isolated and activated into alarm condition.
Entry Guard Time for STAY Mode is the delay time used for all zones except 24-hour
zones when the system is armed in STAY Mode 1 or STAY Mode 2.
If the Entry Guard Time for STAY Mode is programmed and a zone that was not
automatically isolated is activated, the TouchOne beeps twice per second until the
entry timer expires or the system is disarmed. If the alarm condition is not reset by
entering your user code (such as [2580]) before the entry time expires, the sirens
activate into alarm. Only your installer can program this feature.
How to Arm the System in STAY Mode 2
Touch the Keypad button to show the Keypad screen.
Hold down the [0] button until two beeps sound. Then the Home Screen will be
displayed and the Area Card Status will change.
At the end of Exit Time, the TouchOne emits one short beep.
2.3.4 Disarming the System
When you enter the premises after the system is armed in AWAY mode, or if you
armed the system in STAY Mode 1 or STAY Mode 2, you must disarm the system to
disable detection devices that activate an alarm.
If there was an alarm condition prior to disarming the system, the Activation Keypad
screen will display. Once you have disarmed the system, the System Status Button will
scroll through the zones that activated. To view more detail, touch the System Status
Button to open the System Status screen.
How to Disarm the System
If the Keypad Dialog is not automatically displayed, you must touch the Disarm Area
button before proceeding to the next step.
Enter your user code (for example, [2580]).
Two beeps will sound to conrm the system has disarmed.
If you make a mistake when entering your user code, touch the [<] button and try step
2 again.
1110
3 Zones
3.1 Isolating Zones
Use isolating zones to manually disable one or more zones before arming the system.
Once a zone is isolated, you can access that zone during the armed state without acti-
vating an alarm. For example, you need to isolate a zone as, before arming the system,
a PIR detector may be false alarming, or you need to leave a pet inside a particular
zone while away.
If any User Code has the “Code to Isolate” priority level, you will be required to enter
your User Code before being able to isolate a zone.
How to Isolate a Zone
1. From the Home Screen, touch the Settings button.
2. Touch the Zones menu item.
3. Enter a User Code if requested.
4. Under the Zone you want to isolate, slide the Isolate switch from the left to the right
so a tick icon is shown. You can select multiple zones to isolate at a time.
5. Touch the back button in the screen title bar to conrm the isolation action(s) and go
back to the Settings Screen.
6. Two beeps will sound to conrm the zone(s) have been isolated. Touch the back but-
ton in the screen title bar again to go back to the Home Screen.
Please note:
You must complete step 5 before the TouchOne will isolate the zone(s).
3.2 Renaming Zones
Zones can be renamed to provide more meaningful information when being displayed
on the TouchOne, a TEXT LCD Codepad or the RS Control Mobile App. The zone
name must be 12 characters or less.
How to Rename a Zone
1. From the Home Screen, touch the Settings button.
2. Touch the Zones menu item.
3. Enter a User Code if requested.
4. Under the Zone you want to rename, touch the Rename button.
5. The current zone name will be cleared. Using the keyboard, type in the desired zone
name.
6. Touch the enter button on the keyboard to conrm the name.
7. Repeat steps 4 to 6 to rename another zone.
8. Touch the back button in the screen title bar to conrm the renaming action(s) and go
back to the Settings Screen.
1312
Please note:
The renaming process can take up to 20 seconds per zone name that is changed.
4 Users
Only the Master Code holder can add or change other system user codes, including
the Master Code. Up to 32 user codes / radio user codes can be programmed to oper-
ate the system.
4.1 Adding a User
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the [+] button at the right of the screen title bar.
5. Touch the [Edit] button under the PIN section.
6. Enter the digits required for the new code.
7. Touch the back button in the screen title bar to conrm the Add User action and go
back to the Users Screen.
4.2 Deleting a User
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the user you want to delete.
5. Touch the [-] button at the right of the screen title bar.
4.3 Renaming a User
Users can be renamed to provide more meaningful information when being displayed
on the TouchOne, a TEXT LCD Codepad or the RS Control Mobile App. The user
name must be 12 characters or less.
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the user you want to rename.
5. Touch the Rename button.
6. Using the keyboard, type in the desired user name.
7. Touch the enter button on the keyboard to conrm the name.
8. Touch the back button in the screen title bar to conrm the Rename User action and
go back to the Users Screen.
Please note:
The renaming process can take up to 20 seconds.
1514
4.4 Adding / Changing a User Photo
Users can have photos added to them to provide a faster means of identifying them
when you have many users on the system. This photo is only stored on the TouchOne.
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the user you want to add / change the photo of.
5. Touch the Change Photo button.
6. The circle photo image will show the camera. Centre your face in the circle and touch
the Take Photo button. A countdown from 3 will display, and the photo will be taken at
the end of the countdown. A shutter sound will conrm the photo has been taken.
7. Touch the back button in the screen title bar to conrm the Change Photo action and
go back to the Users Screen.
4.5 Editing a User PIN
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the user whose PIN you wish to edit.
5. Touch the [Edit] button under the PIN section.
6. Enter the digits required for the new code.
7. Touch the back button in the screen title bar to conrm the Edit User action and go
back to the Users Screen.
4.6 Adding a Mobile Device
The TouchOne allows you to pair your Bluetooth 3.0 enabled mobile phone with
your user on the Control Panel. When at least one mobile phone has been paired
with a user, 30 seconds after the Control Panel has been armed in AWAY Mode, the
TouchOne will search for your Mobile Phone periodically and automatically disarm
the system with the user PIN that mobile was associated to.
In order for this feature to work, you must have Bluetooth enabled on your phone
when you come within 5 to 10 metres of the TouchOne device.
1. From the Home Screen, touch the Settings button.
2. Touch the Users menu item.
3. Enter your Master Code. The keypad will shake if the code is incorrect.
4. Touch the user your want to associate with your mobile phone. This user’s PIN is en-
tered when your mobile device comes within range.
5. Touch Add Mobile Device
6. On your mobile phone, open the Bluetooth settings and ensure your Bluetooth is on
discoverable mode.
Altri manuali per TouchOne
1
Indice
Altri manuali Bosch Tastiera
Bosch
Bosch CK-M12 Manuale di istruzioni
Bosch
Bosch D1255RB Manuale utente
Bosch
Bosch FMR-7036 Manuale utente
Bosch
Bosch D623 Series Manuale utente
Bosch
Bosch B930 Manuale utente
Bosch
Bosch D720 Manuale utente
Bosch
Bosch D626 Manuale utente
Bosch
Bosch ICP-CP4TS Manuale utente
Bosch
Bosch D220A series Manuale utente
Bosch
Bosch B915I Manuale utente
Bosch
Bosch IUI-UEZ-BE1000s Manuale utente
Bosch
Bosch B920 Manuale utente
Bosch
Bosch Security System Manuale utente
Bosch
Bosch D8229 Manuale utente
Bosch
Bosch B930 Manuale utente
Bosch
Bosch D1255/D1255B Manuale utente
Bosch
Bosch Solution 2000 Manuale utente
Bosch
Bosch D1265 Manuale utente
Bosch
Bosch B920 Manuale utente
Bosch
Bosch D1265 Manuale utente
