Bosch EX40 Manuale utente
EX40
Ultra Vandal-Proof Dome Camera
INSTALLATION INSTRUCTIONS
MAN-40-01
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep this instruction.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install
in accordance with manufacturer instructions.
7. Do not install near any heat sources where the
temperature goes above the product rating.
8. Protect the cabling from being walked on or
pinched particularly at connection points and
where they exit from the apparatus.
9. Only use accessories specified by the
manufacturer.
10. Disconnect this apparatus during lightning
storms or when unused for long periods of
time if precautions are not taken to prevent
lightning/electrical damage to the product.
11. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in a way, such
as internal wiring is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
IMPORTANT
For best results, please read this Instruction Booklet prior to
installing the EX40 camera.
WARNING !
CSA Certified / UL Listed CLASS 2 power adaptors must be used
in order to comply with electrical safety standards.
12-24 VDC/VAC (60Hz), 10W
CSA Type 4
CAN/CSA 60065 – 03 + Amd 1
Audio, Video and Similar Electronic Apparatus – Safety Requirements
UL Std No. 60065 - 07
Audio, Video and Similar Electronic Apparatus – Safety Requirements
This Product Has Been Certified By CSA International To Include the
Health Care Facility Requirements Of UL 2044
This installation should be made by a qualified service person and
conform to all local codes.
Bosch will not be responsible for injuries or damages resulting
from the improper installation or use of any camera sold by
Bosch, their agents, distributors or dealers.
EU Directives covered by this declaration:
72/9/EC Low Voltage Directives
89/336/EEC Electromagnetic Compatibility Directive
NOTE: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. As part of its’
normal operation this device can generate radio
frequency energy and if not installed and used in
accordance with the installation manual may cause
interference to radio communications. However, there
is no guarantee that interference will not occur on a
particular installation. If the device does cause
interference to radio or television reception the user is
encouraged to try to correct the interference by one or
more of the following measures:
1) Fit Ferrite beads on all cable to and from the power
supply box, within the box walls.
2) Route the composite cable between the camera and
the power supply in steel conduit piping over the entire
run of the cable up to and including connection to a
deep conduit base fitted under the camera and a conduit
fitting adaptor in the wall of the PSU box.
3) Contact BOSCH Service Center for further advice.
INDEX – EX40
Page
Description..................................................1
Unpacking...................................................2
Parts List.....................................................2
Items Required for Installation ....................2
Initial Preparations......................................3
Guidelines...................................................3
Section 1. Dome Removal ..........................4
Section 2. Input Power Connections...........6
Section 3. Mounting - Camera Base ...........8
Section 4. Adjustments .............................14
Section 5. Camera Re-Assembly..............21
Section 6. Troubleshooting Guide.............23
Section 7. Template – Mounting Holes .....25
Section 8. General Specifications .............26
1
DESCRIPTION
The EX40 Hi-Impact Dome Camera has been
engineered for surveillance in hostile
environments. Compact and good looking, the
camera features armour-tough construction for
protection against vandalism or against
accidental damage.
An aluminum housing, CNC-machined from a
billet, with an impact resistant polycarbonate
dome and locking retaining ring, make it
extremely rugged and weather-tight.
For viewing adjustment, the CCD Camera/Lens
Assembly can be fully rotated using a unique
“Pan-Tilt-Twist” (PTT) mounting bracket.
A voltage regulator circuit allows for 12V DC or
24V AC operation, and a range in between, also
providing protection from voltage surge,
transient spikes, and reverse voltage.
2
UNPACKING
Care should be taken when unpacking the
shipped unit. Check the parts list and confirm all
items have been located. Inspect the equipment
thoroughly to ensure nothing was damaged in
transit.
Contact BOSCH Service Center if a problem is
noted, see rear page of this booklet for contact
numbers.
PARTS LIST (items supplied with unit)
- EX40 Camera Assembly
- half-tint dome bubble (installed)
- Clear dome bubble (spare)
- Installation Instructions booklet
- Plastic bag containing a hex key and one ½
NPT plug wrapped with Teflon tape
- Desiccant pack for moisture absorption (do not
remove)
ITEMS REQUIRED FOR INSTALLATION
(not supplied with unit)
- Philips, Robertson screwdrivers
- Silicone sealant and Teflon sealing tape.
- Mounting screws, etc.
3
INITIAL PREPARATIONS
Determine the operating voltage at the installation
site. The camera’s Voltage Regulator Board can
accept a 12V DC or 24V AC input.
See Section 2, Input Power Connections.
Determine the optimum location for the camera.
Section 3, Mounting-Camera Base.
All cameras have been tested prior to shipment.
After the wiring has been reconnected, it is
advisable to check the camera’s operation before
installation.
ESD protection – Cameras and circuit boards are
sensitive electronic components. It is
recommended to wear a ground strap to ground
any static charge. (Alternative: touch a grounded
metal plate for at least a minute before proceeding
with any disassembly)
GUIDELINES
The installation of the EX40 camera is explained in
Sections 1 to 5 listed below. It is important that
these steps are followed in sequence:
1. Dome Removal
2. Input Power Connections
3. Mounting - Camera Base
4. Adjustments
5. Camera Re-Assembly
4
1. DOME REMOVAL
The camera’s dome and its retaining ring must
be removed prior to mounting the camera or
performing any wiring disconnections and re-
connections. The setscrews in the retaining ring
are not tightened in the factory and protrude by
1/8" (3mm) in order for the ring to be rotated.
Refer to Figure 1 - 1 on page 5.
Step 1.1 - Place the camera on a flat surface.
Step 1.2 - Press firmly on the dome with one
hand and rotate the retaining ring in
a counter-clockwise direction with
the other hand. Push against the
protruding setscrews with a finger to
rotate the ring. Do not use a
screwdriver or other metal device.
Step 1.3 - Remove the dome and the retaining
ring. Set them aside.
Altri manuali per EX40
1
Indice
Altri manuali Bosch Telecamera di sicurezza
Bosch
Bosch WZ18 Manuale utente
Bosch
Bosch BasicDome Series Manuale utente
Bosch
Bosch WZ45 Istruzioni operative
Bosch
Bosch Diniop IP - NWC-0455 Manuale utente
Bosch
Bosch EX10C704B‑N Manuale utente
Bosch
Bosch LTC 0465 Series Manuale utente
Bosch
Bosch WZ20NXV550-0 Manuale utente
Bosch
Bosch EXTEGRA IP 9000 FX Manuale utente
Bosch
Bosch NDS-5703-F360 Manuale utente
Bosch
Bosch DINION 7100i IR Manuale utente
Bosch
Bosch VDC?480 Series Manuale utente
Bosch
Bosch VC973650T Manuale utente
Bosch
Bosch EX72C7V0922-N Manuale utente
Bosch
Bosch NBC-265-P Istruzioni per l’uso
Bosch
Bosch Dinion Manuale utente
Bosch
Bosch VDN-498V03-11 Manuale utente
Bosch
Bosch VJR-F801-ICCV Manuale utente
Bosch
Bosch MIC Series 550 Manuale utente
Bosch
Bosch VDN-5085 Manuale utente
Bosch
Bosch VDC-275 Manuale utente
