Bosch AMAX panel 2000 ICP-AMAX-P Manuale utente

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500

en User Guide

AMAX panel 2000 / AMAX panel 2000 EN Table of Contents | en 3

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Table of Contents

1 Introduction 4

2 Arming and Disarming the System 8

2.1 Arming the System 8

2.1.1 Arming in AWAY mode 8

2.1.2 Arming in STAY mode 9

2.1.3 Forced arming 9

2.2 Disarming the System 9

2.2.1 Disarming with CODE 9

2.2.2 Disarming with wireless control Key 9

2.2.3 Disarming with Key switch 9

3 Faults or Tamper conditions 10

3.1 System fault or tamper analysis Mode 10

4 Walk test mode 12

5 Event Memory Recall mode 13

6 Reset the Control Panel 14

7 Bypassing 15

7.1 Bypassing Zones 15

7.2 Bypassing Faults and Tamper conditions (Except Zone Tampers) 15

8 Enable / Disable the installers code 16

9 Change individual code 17

10 Keypad alarm operation commands 18

10.1 Duress alarm 18

10.2 Keypad panic alarm 18

10.3 Keypad fire alarm 18

10.4 Keypad medical alarm 18

11 Domestic Dialing 19

Glossary 20

Index 21

4en | Introduction AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

1 Introduction

Quick keypad operation instructions

Table 1.1 Quick keypad operation instructions

ICP-AMAX - LED8-8 Zone LED Keypad ICP-AMAX-LCD8 - 8 Zone LCD Keypad

Arming

AWAY arm [code] + [#] / [#] (quick arming)

STAY arm [code] + [*] / [*] (quick arming)

Disarming

Disarm [code] + [#]

Other Commands

Fault and

Tamper Analysis

[code] + [2] [#]

Walk test [code] + [4] [#]

Event recall [code] + [5] [#]

System Reset [code] + [6] [#]

Bypassing zones [code] + [9] [#] [zone] + [*] [#]

Bypassing Faults

and Tamper

conditions

[code] + [97] [#]

Enable/Disable

Installer code

Enable = [code] + [98] [#] Disable = [code] + [98] [*]

Change

individual code

[code] + [99] [#] [newcode] [#]

Alarm Commands

Duress alarm [code] + [0] [#]

Emergency

alarm

Simultaneously press and hold [1] and [3] or [*] and [#]

Fire alarm Simultaneously press and hold [4] and [6]

Medical alarm Simultaneously press and hold [7] and [9]

Default user code = 2580

AMAX panel 2000 / AMAX panel 2000 EN Introduction | en 5

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Keypad Indicators

Table 1.2 Keypad Indicators

LCD keypad

indicator icons

LED keypad

indicator lights

Status Definition

Zone (1-8) on Zone is triggered.

off Zone is normal.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Zone was alarmed or is in alarm

status.

Slow flash (1 second lights on/1

second lights off)

Zone is manually bypassed or

interior Zone is in STAY ARM mode.

AWAY on System is armed in AWAY mode.

off System not armed in AWAY mode.

Slow flash (1 second lights on/1

second lights off)

Exit time.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Programming mode or Code

function mode. STAY indicator

flashes simultaneously.

STAY on System is armed in STAY mode.

off System not armed in STAY mode.

Slow flash (1 second lights on/1

second lights off)

Exit time.

Fast flash (0.25 seconds lights on/

0.25 seconds lights off)

Programming mode or Code

function mode. AWAY indicator

flashes simultaneously.

When bypass function is

performed, the STAY indicator only

flashes.

MAINS on AC main power is normal.

Slow flash (1 second lights on/1

second lights off)

AC main power supply failed.

FAULTS on System fault or Tamper condition

is present.

off System is in normal status.

Flashes System fault or Tamper condition

must be acknowledged.

on System is disarmed.

1 2 3 ….

6en | Introduction AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

Keypad sounds

Table 1.3 Keypad sounds

Sound indicator Definition

One short beep A keypad button has been pressed.

One single one-

second beep

The requested operation is refused. Incorrect operation signal.

Two short beeps The system accepted the code. The system executed the requested

function.

One short beep

per second

In walk test mode.

One short beep

every two

seconds

Exit time started.

Continued

sound

– Last 10s on exit time

– Keypad fault/tamper sound (fault/tamper to be acknowledged)

– Keypad alarm sound

Continuous 0.5

second beep,

stops 0.5

seconds

Entry delay time (until alarm ends or system is disarmed).

AMAX panel 2000 / AMAX panel 2000 EN Introduction | en 7

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

Zone description

Zone 1 ______________________________________________________

Zone 2 ______________________________________________________

Zone 3 ______________________________________________________

Zone 4 ______________________________________________________

Zone 5 ______________________________________________________

Zone 6 ______________________________________________________

Zone 7 ______________________________________________________

Zone 8 ______________________________________________________

Exit Time ___________________________________________________ sec

Entry Time _________________________________________________ sec

User Code Names

Code 1 _____________________________________________________

Code 2 _____________________________________________________

Code 3 _____________________________________________________

Code 4 _____________________________________________________

Code 5 _____________________________________________________

Code 6 _____________________________________________________

Code 7 _____________________________________________________

Code 8 _____________________________________________________

Code 9 _______________________________________________________Keyfob 1

Code 10 _____________________________________________________ Keyfob 2

Code 11 _____________________________________________________ Keyfob 3

Code 12 _____________________________________________________ Keyfob 4

Code 13 _____________________________________________________ Keyfob 5

Code 14 _____________________________________________________ Keyfob 6

Code 15 _____________________________________________________ Keyfob 7

Code 16 _____________________________________________________ Keyfob 8

8en | Arming and Disarming the System AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

2 Arming and Disarming the System

2.1 Arming the System

2.1.1 Arming in AWAY mode

Arming the system in AWAY Mode is normally performed when you leave the premises and

require that all zones are activated in a ready state to detect an intrusion.

2.1.1.1 Keypad arming

The system can be set to AWAY mode in two different ways.

To arm the System in AWAY mode (method 1)

Enter your code and press [#].

Two beeps sound, the AWAY indicator flashes slow, and exit time starts. After exit time, the

AWAY indicator turns is lit.

To arm the System in AWAY mode (method 2)

Press and hold [#] until it beeps twice.

The AWAY indicator flashes slow, and exit time starts. After exit time, the AWAY indicator is lit.

Please contact your installer to enable/disable this function.

2.1.1.2 Telephone remote arming

The user dials the control panel number. The control panel answers the call and issues a long

beep. After the long beep, the user must press the [#] key. When the Panel receives the signal

it will confirm the arming of the control panel with a high tone.

Please contact your installer to enable/disable this function.

2.1.1.3 Arming in AWAY mode with wireless remote control Key

Press and hold the Arming Button until two beeps sound on the remote keypad and the AWAY

indicator flashes slow. Exit time starts. After exit time, the AWAY indicator is lit.

NOTICE!

When the number of incorrect code entries on the keypad reaches a specified number, the

keypad will automatically lock for 180 seconds and alarm is reported.If the keypad is idle for 4

minutes, the system will automatically exit from any operational mode.

RE012E:2 standard wireless remote control key

1 –Button 1: Arm in AWAY mode

2 –Button 2: Disarm

3 –Button 1 and 2: Press both buttons at the same time to activate Panic alarm

1 2

AMAX panel 2000 / AMAX panel 2000 EN Arming and Disarming the System | en 9

Robert Bosch Engineering and Business Solutions Limited User Guide F.01U.249.500 | V2 | 2011.11

2.1.1.4 Key switch arming

Users can use a key switch to Arm and Disarm the system. When the Key switch is activated,

the AWAY indicator flashes slow and exit time starts. After exit time, the AWAY indicator is lit.

When the Key switch is deactivated, the system is disarmed and Away indicator is off.

2.1.2 Arming in STAY mode

STAY Mode is used when you need to arm the perimeter and unused areas of the premises to

detect a would-be intruder, while at the same time being able to move freely within an area

that is automatically isolated

There are two methods to arm your system in STAY Mode

To arm the system in STAY mode (method 1)

Enter your code and press [#].

Two beeps sound, the STAY indicator flashes slow and exit time starts. After exit time, the

STAY indicator is lit.

The lights corresponding to all zones programmed as automatically isolated zones (Interior

Instant Zone) begin to flash and continue until the exit time is finished.

To arm the system in STAY mode (method 2)

Press and hold [#] for 3 seconds.

When two beeps sound, release the button.

The STAY indicator flashes slow and exit time starts. After exit time, the STAY indicator is on.

Please contact your installer to enable/disable this function.

2.1.3 Forced arming

Arming the system when a zone is not sealed is known as forced arming. If the AWAY indicator

does not glow, and if a long beep sounds when you attempt to arm the system in AWAY Mode,

then forced arming is not permitted. If this is the case, then you will have to seal all zones or

manually isolate them before you can arm the system.

Please contact your installer to enable/disable this function.

2.2 Disarming the System

2.2.1 Disarming with CODE

Enter your code and press [#] .Two beeps sound and the AWAY or STAY indicator is

extinguished.

2.2.2 Disarming with wireless control Key

Press and hold the Disarming Button. Two beeps sound and the AWAY or STAY indicator is

extinguished.

2.2.3 Disarming with Key switch

When the Key switch is deactivated, the system is disarmed and the AWAY or STAY indicator is

extinguished.

10 en | Faults or Tamper conditions AMAX panel 2000 / AMAX panel 2000 EN

F.01U.249.500 | V2 | 2011.11 User Guide Robert Bosch Engineering and Business Solutions Limited

3 Faults or Tamper conditions

Whenever a system fault or tamper condition occurs, the FAULT or MAINS indicator flashes

and the keypad beeps.

3.1 System fault or tamper analysis Mode

To enter fault or tamper analysis mode for determining a system fault or tamper condition:

1. Enter your Code and [2] and press [#]. Two beeps sound.The FAULT indicator remains lit

and the STAY and AWAY indicators flash. The lit zone indicators indicate the type of fault

or tamper condition that occurred.

2. For a multi-level menu, enter the corresponding number to enter the submenu, press [ 0

] key to return to the main menu.

3. To exit from Fault and Tamper Analysis Mode, press [#] . The STAY and AWAY indicators

are extinguished and the FAULT indicator remains lit, and the keypad stops the beep.

NOTICE!

Operation can be carried out only in status.

Altri manuali per AMAX panel 2000 ICP-AMAX-P

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Bosch Sistema di sicurezza

Bosch

Bosch D222 Manuale utente

Bosch

Bosch LTC 1311/20 FlexiDome I Manuale utente

Bosch

Bosch AMAX 2100 Manuale di istruzioni

Bosch

Bosch DIVAR IP all-in-one 7000 3U Manuale utente

Bosch

Bosch Security Systems Manuale utente

Bosch

Bosch DB24C4200R2 Manuale utente

Bosch

Bosch UEZ Manuale utente

Bosch

Bosch NBN-733 Istruzioni per il montaggio

Bosch

Bosch Solution 16i Manuale utente

Bosch

Bosch LTC 8016/90 Manuale utente

Bosch

Bosch CM705B Come usare

Bosch

Bosch DB-CO Manuale utente

Bosch

Bosch 7100 Manuale utente

Bosch

Bosch B4512 Manuale utente

Bosch

Bosch Spexor Manuale utente

Bosch

Bosch FMC-210-SM Manuale utente

Bosch

Bosch FW5.50 Istruzioni per il montaggio

Bosch

Bosch Solution 2000 Series Istruzioni operative

Bosch

Bosch VSS7902/00T Guida rapida

Bosch

Bosch AMAX 2100 Manuale utente

Bosch

Bosch Security System Manuale utente

Bosch

Bosch PR109B Manuale utente

Bosch

Bosch ND 200 LSN Manuale utente

Bosch

Bosch Plena Power Amplifier Istruzioni per il montaggio

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente