Bosch BCC100 Manuale utente
1
boschheatingandcooling.com
Bosch Connected Control
BCC100 Wi-Fi Thermostat User Guide
1
Contents
WARNING: Failure
to follow and read
all instructions
before installing or
operating this device
may cause personal
injury and/or
property damage.
IN THE BOX:
▶BCC100 Wi-Fi Thermostat
▶Two screws and anchors
▶Flathead screwdriver
▶Wire labels
▶Jumper wire
▶User guide
Some features require
an internet connection
and a user account.
Features,
specifications, and
appearance are
subject to change
without notice.
C-wire (24Vac)
required to power
the thermostat.
CHECK COMPATIBILITY FIRST
For conventional (gas/oil/electric) ▶Heat Only ▶Cool Only
For heat-pump systems ▶Up To 4-Heat & 2-Cool
Getting Started.......................2
Main Screen............................7
Icons.......................................8
Initialization..........................10
Wi-Fi Setup...........................14
App Setup.............................17
Starting Your System............19
Temporary Scheduling..........21
Programming Schedules.......22
Additional Features
...............
24
Advanced Features...............28
Warranty
...............................
29
Connected Solution for 24Vac Thermostat Systems
2
Getting Started
The BCC100 thermostat is designed to work on most 24Vac
low voltage heating and cooling systems such as gas and oil
furnaces, heat pumps, and single or dual-stage systems.
Professional installation recommended for:
▶Humidifiers and dehumidifiers
Turn Power Off
Please turn off the unit’s main power at the circuit panel
before beginning the installation process.
POWER OFF WARNING:
Failure to turn off power may result in
electrical shock and/or system damage.
Remove the Old Thermostat
Before removing the wires from the thermostat or wall
plate, take a photo of all wires for reference, then label
each wire according to the terminal codes.
Disconnect the wires from the old thermostat one by
one. Do not let wires fall back into the wall. Remember,
the power to your HVAC system must be turned
off. Remove the old wall plate.
1
After labeling the wires, we recommend securing
them to an object such as a pen or clip to prevent
them from falling back into the wall.
3
Connect the New Wall Plate
Insert all wires vertically from the open socket into the
proper terminal. Ensure that each wire is inserted into the
matching terminal. Use the supplied flathead screwdriver
to fasten each wire. Pull wires gently to ensure wires are
securely fastened.
3
WARNING: Use caution when securing and routing
wires to prevent possible shortage to adjacent terminals.
KEY
Rc Power Cooling W/E 1st Stage Heating
Emergency heat activated at W1
Rh Power Heating W2 2nd Stage Heating
Auxiliary heat activated at W2
CCommon O/B Reversing Valve
GFan H/Dh (De) Humidifier
Y1st Stage
Compressor Data Alarm Input
(Only to be used with Bosch WSHP)
Y2 2nd Stage
Compressor Jumper
Mount the New Wall Plate
Use the enclosed screws and anchors to
mount the new wall plate. In most cases,
you can utilize the same mounting position of your old
thermostat. Be sure to check the alignment of your wall
plate before installation.
2
Note: the color of your wires may not be the same as what’s shown in this User Guide
4
Conventional Heating
(2 Stages) & Cooling
(2 Stages) System with
Humidifier and Single
Transformer
Install a jumper between Rh
and Rc only if a single
transformer is used for
heating and/or cooling.
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
Conventional Heating
(1 Stage) & Cooling
(1 Stage) System with
Dual Transformer
The following are wiring diagrams for common
systems. If you are unsure of how to connect your
thermostat, please seek professional support.
Conventional Heating
(1 Stage) & Cooling
(2 Stages) with
Dehumidifier and
Single Transformer
Install a jumper between Rh
and Rc only if a single
transformer is used for
heating and/or cooling.
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
5
Heat Pump 4 Heat /
2 Cool with Dehumidifier
▶Connect Rc to Rh
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
Heat Pump 3 Heat / 2 Cool
▶Connect Rc to Rh
▶Connect W to W2 to
operate both stages of
electric heat at the
same time
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
Heat Pump
2 Heat / 1 Cool
with Emergency Heat
▶Connect Rc to Rh
-
G
W2
Y2
O/B
H/Dh
Data
C
W/E
Y
Rh
Rc
Thermostat
6
Attach BCC100 to the Wall
First align the two
clips on the back of
the BCC100 into the
corresponding slots
on the top of the
wall plate.
4
Firmly press forward
until you hear a click to
secure the thermostat
into position.
1
2
PUSH
CLIPS
Ensure the C-wire is properly connected to the heating and
cooling equipment and thermostat. Switch the power back
on for the heating/cooling system at the main switch box.
7
Your thermostat should power on and prompt you to start
the setup. If you are having trouble powering the
thermostat, please refer to boschheatingandcooling.com
for additional support.
Thank you for choosing the BCC100. Enjoy the savings
and comfort of owning a Bosch connected thermostat!
Main Screen
System
Mode
Main Menu Fan
Status Wifi / Cloud Access
Indicator
Current
Room
Humidity Current Room
Temperature
Current
Schedule
Adjust
Temperature
Set-Points
Power On and Enjoy!
5
8
Icons
Menu
Exit / Save Settings
Back
Weather
Schedule
Device Settings
System Settings
Advanced Settings
Heat Mode
Cool Mode
Auto Mode
Emergency Heat Mode
Off
Gas/Oil/
Propane
Heat Pump
Electric
Auto
On
Circulation
Humidifier
Dehumidifier
System Modes
Basic Icons Heating Types
Fan Modes
Humidity
8
9
Icons
9
Schedule on Device
Schedule on Cloud
Wi-Fi Connection Established
Wi-Fi Connection Not Established
Internet is Not Available
Retry Internet Connection
System Connectivity
Unit Operation
1 2
12
1 2
1 2
4
Heating on (1st stage) & (2nd stage) - Heat Mode
Cooling on (1st stage) & (2nd stage) - Cool Mode
Heating on (1st stage) & (2nd stage) - Auto Mode
Cooling on (1st stage) & (2nd stage)- Auto Mode
Fan on/running - Fan Auto Mode
Emergency heat on
Auxiliary heat on - 2nd Aux Stage of a
4-stage heating system
Auxiliary
Heating
Emergency
Heating
Altri manuali per BCC100
4
Indice
Altri manuali Bosch Termostato
Bosch
Bosch TSTBM-RRS--TW-A Manuale utente
Bosch
Bosch CR 20 RF Manuale utente
Bosch
Bosch Radiator thermostat II Manuale dell'operatore
Bosch
Bosch CRC R-1 Manuale utente
Bosch
Bosch CR 50 Manuale utente
Bosch
Bosch TR 200 Manuale utente
Bosch
Bosch RT10-RF Manuale utente
Bosch
Bosch BCC100 Manuale di servizio
Bosch
Bosch TRZ 12-2 Manuale utente
Bosch
Bosch CR 11 Manuale utente
Bosch
Bosch MT 10 Manuale utente
Bosch
Bosch Climate 5000 Series Manuale utente
Bosch
Bosch OR30 OT Manuale utente
Bosch
Bosch FR 10 Manuale utente
Bosch
Bosch BCC50 Istruzioni per il montaggio
Bosch
Bosch OR80 OT Manuale utente
Bosch
Bosch Worcester Greenstar Comfort II RF Manuale utente
Bosch
Bosch DT1 Manuale utente
Bosch
Bosch 8-733-944-325 Guida
Bosch
Bosch FW 100 Manuale utente
