Bounty Hunter Outback Manuale utente

ACCESSORIES

Gold

Prospecting Kits

FOR COMPLETE DETAILS VISIT WWW.DETECTING.COM • 1-800-413-4131

Carry Bag

Rugged double-stitched construction

CBAG2

Pouch & Digger Combo

Pouch with 2 large pockets & 9” heavy duty digging tool. TPKIT-W

Bounty Hunter Stereo Headphones

Use with Bounty Hunter metal detectors. Lightweight and adjustable with

true stereo sound, adjustable volume, 1/8 jack with 1/4 adaptor,

4’ cable.

HEAD-W

Pin Pointer

Pinpoints the exact location of buried metal objects. Audio signal indicator

and vibrator. Runs on 1 – 9-Volt Battery. PIN POINTER-W

Sand Scoop

Large scoop with filtering holes. Made of strong plastic. SAND SCOOPBH

Replacement Search Coil

7” Standard Coil (replacement) - 7COIL-EX

9” Heavy-Duty Digging Tool

Metal blade with comfortable plastic handle and depth gauge TROWEL-2

Digging Tool

Light and practical wide blade digging tool. TROWEL-W

Bounty Hunter Baseball Cap

One size fits all, with Bounty Hunter®logo.

Bounty Hunter T-Shirt

100% cotton with Bounty Hunter®Logo. Sizes – LG, XL & XXL

OWNER’S MANUAL

The

Outback is an

easy to use detector.

The most difficult aspects of

metal detecting have been automated.

However, if you are new to the hobby,

we strongly recommend that you:

1) Adjust the Sensitivity to a low setting

in the event of false signals. Always begin

use at a reduced sensitivity level; increase to full

sensitivity after you have become familiar with the

detector.

2) Do not use indoors. This detector is for outdoor use only. Many

household appliances emit electromagnetic energy, which can

interfere with the detector. If conducting an indoor demonstration,

turn the sensitivity down and keep the search coil away from

appliances such as computers, televisions and microwave ovens.

If your detector beeps erratically, turn off appliances and lights

(especially those with dimmer switches).

Also keep the search coil away from objects containing metal, such

as floors and walls.

3) Read this manual. Most importantly, review the Quick-Start Demo

(p.7) and Basic Operation (pp. 9-12).

4) Use 9-volt ALKALINE batteries only. Do not use Heavy Duty

Batteries.

MOUTBACK Rev2 122812

TABLE OF CONTENTS

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . .7-8

Basic Operation

Powering Up . . . . . . . . . . . . . . . . . . . . . . .9

The Display . . . . . . . . . . . . . . . . . . . . . .9-10

Mode Control (discrimination) . . . . . . . . .11

Discrimination Settings . . . . . . . . . . . . . .12

Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Audio Target Identification . . . . . . . . . . . . . . .13

Sensitivity Adjustment . . . . . . . . . . . . . . . . . . .14

In The Field Techniques . . . . . . . . . . . . . . .15-17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .18

Treasure Hunter’s Code of Ethics . . . . . . . . . . .19

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Accessories . . . . . . . . . . . . . . . . . . . . .Back Cover

According to FCC part 15.21 Changes or Modifications made to this device not expressly approved by

the party responsible for compliance could void the users authority to operate this equipment.

Published by First Texas Products, L.L.C.

Bounty Hunter®is a registered trademark of First Texas Products, L.L.C.

www.detecting.com

First Texas Products, LLC

1465-H Henry Brennan

El Paso, TX 79936

(915) 633-8354

TREASURE HUNTER’S CODE OF ETHICS:

• Always check Federal, State, County and local laws before searching.

• Respect private property and do not enter private property without the owner’s permission.

• Take care to refill all holes and leave no damage.

• Remove and dispose of any and all trash and litter found.

• Appreciate and protect our inheritance of natural resources, wildlife and private property.

• Act as an ambassador for the hobby, use thoughtfulness, consideration and courtesy at all

times.

• Never destroy historical or archaeological treasures.

• All treasure hunters may be judged by the example you set; always conduct yourself with

courtesy and consideration of others

First Texas Products, L.L.C.

Five Year Limited Warranty

Bounty Hunter Metal Detectors are warranted against

defects in workmanship or materials under normal

use for five years from date of purchase to the

original user. Liability in all events is limited to the

purchase price paid. Liability under this Warranty is

limited to replacing or repairing, at our option, any

Bounty Hunter Detector returned, shipping cost

prepaid, to First Texas Products, L.L.C. Damage due

to neglect, accidental damage or misuse of this

product is not covered by this warranty.

Proof of purchase is required to make a claim under this warranty.

NOTE TO CUSTOMERS OUTSIDE THE U.S.A.

This warranty may vary in other countries, check with your distributor for details.

Warranty does not cover shipping costs.

TERMINOLOGY

The following terms are used throughout the manual, and are standard

terminology among detectorists.

ELIMINATION

Reference to a metal being "eliminated" means that the detector will

not emit a tone, nor light up an indicator, when a specified object

passes through the coil’s detection field.

DISCRIMINATION

When the detector emits different tones for different types of metals,

and when the detector "eliminates" certain metals, we refer to this

as the detector "discriminating" among different types of metals.

Discrimination is an important feature of professional metal

detectors. Discrimination allows the user to ignore trash and

otherwise undesirable objects.

RELICA relic is an object of interest by reason of its age or its association

with the past. Many relics are made of iron, but can also be made

of bronze or precious metals.

IRON Iron is a common, low-grade metal that is an undesirable target in

certain metal detecting applications. Examples of undesirable iron

objects are old cans, pipes, bolts, and nails.

Sometimes, the desired target is made of iron. Property markers,

for instance, contain iron. Valuable relics can also be composed of

iron; cannon balls, old armaments, and parts of old structures and

vehicles can also be composed of iron.

FERROUS

Metals which are made of, or contain, iron.

PINPOINTING

Pinpointing is the process of finding the exact location of a buried

object. Long-buried metals can appear exactly like the surrounding

soil, and can therefore be very hard to isolate from the soil.

PULL-TABS

Discarded pull-tabs from beverage containers are the most

bothersome trash items for treasure hunters. They come in many

different shapes and sizes. Most pull-tabs can be eliminated with

the Mode Control, but some other valuable objects can have a

magnetic signature similar to pull-tabs, and will also be eliminated

when discriminating out pull-tabs.

GROUND BALANCE

Ground Balancing is the ability of the detector to ignore, or "see

through," the earth’s naturally occurring minerals, and only sound

a tone when a metal object is detected.

TROUBLESHOOTING GUIDE

SYMPTOM CAUSE SOLUTION

Detector chatters • Using detector • Use detector

or beeps erratically indoors outdoors only

• Using detector near • Move away

power lines

from power lines

• Using 2 detectors in • Keep 2 detectors

close proximity at least 20’ apart

• Highly oxidized • Only dig up

buried object repeatable

signals

• Environmental •

Reduce sensitivity

electromagnetic until erratic

interference signals cease

Constant low tone •

Discharged batteries

• Replace batteries

constant repeating

tones

• Wrong type of • Use only 9V

batteries alkaline batteries

LCD does not lock • Multiple targets •

Move coil slowly

on to one target ID present at different angles

or detector emits • Highly oxidized

multiple tones target

• Sensitivity set • Reduce sensitivity

too high

No power, no • Dead batteries • Replace batteries

sounds • Cord not connected

• Check connections

securely

TROUBLESHOOTING

IN THE FIELD TECHNIQUES

(continued)

ASSEMBLY

Adjusting the Armrest

Most people will find the standard position

of the armrest very comfortable. Very large

forearms and short forearms (particularly

children’s arms), can be accommodated by

moving the armrest forward.

The armrest may be moved forward or

backwards by removing the single screw

and nut, and then repositioning the 2-piece

armrest. Users with shorter arms may find

the armrest more comfortable in the

forward position. In order to move the

armrest backwards, the plastic plug must

be removed from the aluminum tube.

Armrest Strap

(optional accessory)

The strap is available for purchase as a

separate accessory. Some users prefer to

use the strap when swing the detector

vigorously, in order to hold the detector

secure against the arm.

The detector can also be used without the

strap, with no compromise to detector

balance and stability under most conditions.

Upper

Stem

Silver

Button

Searchcoil

Cable

Searchcoil

you many have encountered

multiple objects. If you are

new to the hobby, you may

want to dig all targets at first.

With practice in the field, you

will learn to better discern the

nature of buried objects by the

nature of the detector’s

response.

You may encounter some false

signals as you proceed. False

signals occur when the detector

beeps, but no metal target is

present. False signals can be

induced by electromagnetic

interference, oxidation, or

highly mineralized ground

soils. If the detector beeps

once, but does not repeat the

signal with several additional

sweeps over the same spot,

there is probably no target

present.

When searching very trashing

ground, it is best to scan small

areas with slow, short sweeps.

You will be surprised just how

much trash metal and foil you

will find in some areas. The

trashiest areas have been

frequented by the most people,

and frequently hold the most

promise for finding the most

lost valuables.

Also maintain the searchcoil

positioned just above the

surface of the ground, without

making contact with the

ground. Making contact with

the ground can cause false

signals.

ASSEMBLY

Swing the search coil slowly,

overlapping each sweep as you

move forward. It is important

to sweep the coil at a consistent

speed over the ground as you

search. After identifying a

target, your sweep technique

can help in identifying both the

location and the nature of the

target. If you encounter a weak

signal, try moving the coil in

short, rapid sweeps

over the target zone;

such a short rapid

sweep may provide

a more consistent

target

identification.

Most

worthwhile

objects

will

respond with a repeatable tone.

If the signal does not repeat

after sweeping the coil directly

over the suspected target a few

times, it is more than likely

trash metal.

Crossing the target zone with

multiple intersecting sweeps at

multiple angles is another way

to verify the repeatability of the

signal, and the potential of the

buried target. To use this

method, walk around the target

area in a circle, sweeping the

coil across the target

repeatedly, every 30 to 40

degrees of the circle, about ten

different angles as you walk

completely around the target.

If a high-tone target completely

disappears from detection at a

given angle, chances are that

you are detecting oxidized

ferrous metals, rather than a

silver or copper object. If the

tone changes a different angles,

IN THE FIELD TECHNIQUES

(continued)

WHAT

READS

LIKE THIS

…MAY

ACTUALLY

BE THIS

Assembling your Challenger Metal Detector is easy

and requires no tools. Just follow these steps:

●

1Using the supplied bolt and knurled knob,

attach the search coil to the lower

stem.

●

Press the button on the

upper end of the lower

stem and slide the

lower stem into the

upper stem.

Adjust the stem

to a length that lets

you maintain a comfortable upright posture, with your arm

relaxed at your side.

Maintain the search coil

about 1 inch above the

ground as you sweep.

●

3Wind the search coil cable

around the stem. Leave enough slack in the cable to let you

adjust the coil when you are hunting on uneven ground. Then

tighten the knob at the end of the search coil.

Note:

To adjust the coil,

simply loosen the knob.

●

4Insert the coil’s plug into

the matching connector on

the control housing. Be

sure the holes and pins

line up correctly.

Caution: Do not force the

plug in. Excess

force will cause

damage.

To disconnect the

cable, pull on the

plug.

Do not pull

on the cable.

IN THE FIELD TECHNIQUES

When pinpointing a target, try drawing an “X”,

as illustrated, over where the tone is induced.

PINPOINTING

Accurate pinpointing takes practice

and is best accomplished by

“X-ing” the target area.

1. Once a buried target is indicated

by a good tone response,

continue sweeping the coil over

the target in a narrowing

side-to-side pattern.

2. Take visual note of the place on

the ground where the “beep”

sounds.

3. Stop the coil directly over this

spot on the ground.

4. Now move the coil straight

forward and straight back

towards you a couple of times.

5. Again make visual note of the

spot on the ground at which

the “beep” sounds.

6. If needed, “X” the target at

different angles to “zero in” on

the exact spot on the ground at

which the “beep” sounds.

COIL MOVEMENT

When swinging the coil, be

careful to keep it level with the

ground about one inch from the

surface. Never swing the coil like

a pendulum.

CORRECT

WRONG

Use ALKALINE

batteries only.

To install the

batteries:

●

1Remove the

battery cover by

disengaging the

clip at the back.

●

2Align the polarity

of the batteries

correctly, with

the positive "+"

toward the coil

plug connection,

as indicated by

the + and –

indicators on the

housing.

●

3Insert (2) 9-Volt ALKALINE batteries, with the contacts pointed inward,

and press down on the back of the batteries to snap them into place.

Some brands of batteries will require moderate force to clear the

retaining tabs.

●

4Replace the battery door.

The Low Battery Indicator will come on and stay on if the batteries need

to be replaced.

Most metal detector problems are due to improperly installed batteries,

or the use of non-alkaline or discharged batteries. If the detector does

not turn on, please check the batteries.

BATTERIES

DO NOT MIX OLD AND NEW BATTERIES

QUICK-START DEMONSTRATION

I. Supplies Needed

• A Nail • A Quarter

•A Pull-Tab from a beverage can • A Zinc Penny (dated after 1982)

II. Position the Detector

a. Place the detector on a

table, with the search coil

hanging over the edge.

(or better, have a friend

hold the detector, with

the coil off the ground)

b. Keep the search coil away

from walls, floors, and

metal objects.

c. Remove watches, rings and other jewelry or metal objects from

hands and wrists.

d. Turn off appliances or lights that cause electromagnetic interference.

e. Pivot search coil back toward the

detector body.

III. Power Up

Press the ON touchpad.

The detector will beep twice and

the full sensitivity setting will be

indicated on the left of the display.

IV. Wave each Object over the Search Coil

a. Notice a different tone for each object.

Low Tone: Nail

Medium Tone: Pull-tab & Zinc Penny

High Tone: Quarter

b. Motion is required. Objects must be in motion over the search coil

to be detected.

V. Press the MODE touchpad(*)

The detector will beep twice and

the sensitivity setting will flash

on the left side of the display.

Quick-Start Demo continued on next page

Upon power-up, the detector defaults to 3/4 sensitivity. To increse to full

sensitivity, press the Sensitivity ▲ touch pad.

ELECTROMAGNETIC INTERFERENCE

The principle use for the Sensitivity Control is to eliminate

Electromagnetic Interference (EMI).

A hobby metal detector is an extremely sensitive device; the search coil

creates its own magnetic field and acts like an antenna. If your detector

beeps erratically when the search coil is motionless, the unit is probably

detecting another magnetic field.

Common sources of EMI are electric power lines, both suspended and

buried, motors, and household appliances like computers and

microwave ovens. Some indoor electronic devices, such as dimmer

switches used on household lighting, produce severe EMI and will cause

the detector to beep erratically. Other metal detectors also produce their

own electromagnetic fields, so if detecting with a friend, keep two metal

detectors at least 20 feet apart.

If the detector beeps erratically, REDUCE THE SENSITIVITY by pressing

the Down-Sensitivity Arrow ▼ on the left of the control panel.

SEVERE GROUND CONDITIONS

A secondary use for the Sensitivity Control is to reduce false detection

signals caused by severe ground conditions. While your Outback

contains circuitry to eliminate the signals caused by most naturally

occurring ground minerals, 100% of all ground conditions cannot be

anticipated. Highly magnetic soils found in mountainous and gold-

prospecting locations can cause the detector to emit tones when metal

objects are not present. High saline content soils and sands can also

cause the detector to false.

If the detector emits false, non-repeatable, signals, REDUCE THE SENSITIVITY.

MULTIPLE TARGETS

If you suspect the

presence of deeper targets

beneath a shallower target,

reduce the sensitivity to

eliminate the detection of

the deeper targets, in order

to properly locate and

identify the shallower

target.

SENSITIVITY ADJUSTMENT

AUDIO TARGET IDENTIFICATION

While the LCD (Liquid Crystal Display) is very accurate in identifying

buried objects, the user in the field does not always maintain the display

screen in his field of vision. Therefore, we have incorporated an audio

feedback mechanism to alert the user to the nature of buried objects.

This audio feedback system first alerts the user to the presence and

classification of objects, whose nature and location can be confirmed

using the LCD display.

The detector will sound three different tones. These three tones

correspond to the three target categories depicted on the LCD display.

LOW TONE

Ferrous objects, such as iron and steel, will induce a low tone.

Small gold objects can also induce a low tone.

MEDIUM TONE

Pull-tabs, newer pennies (post-1982), larger gold objects, zinc,

small brass objects, and most bottle screw caps will induce

medium tones. Many recent vintage foreign currencies will

induce medium tones, including loonies & toonies.

HIGH TONE

Silver and copper coins, larger brass objects, older pennies (pre-

1982), and highly oxidized metals will induce high tones.

Quarters, dimes and other precious coins fall into this category.

Audio Target Identification (ATI) classifies metals into three categories.

LOW TONE

Nails, Bottle Caps,

& Small Gold

MEDIUM TONE

Old & New Pull Tabs, Zinc US Pennies

(Post 1982), Nickel, Larger Gold

Objects, Pennies, Loonies & Toonies.

HIGH TONE

Copper, Silver & Brass

Copper Pennies (Pre 1982)

VI. Press the MODE touchpad again.(*)

a. A flashing indicator will point toward IRON.

b. The flashing indicator tells us that Iron has

been eliminated from detection.

VII. Wave the Nail over the Search Coil

a. The Nail will not be detected.

b. The Nail has been "Discriminated Out."

VIII. Wave the Quarter, Penny, and Pull-Tab

over the Search Coil

These non-ferrous objects will be detected with their own

distinctive tones.

IX. Press the MODE touchpad again.(*)

a. The detector will beep twice and the sensitivity setting will flash on

the left side of the display.

b. Notice the flashing arrow pointing toward Iron.

The flashing arrow indicates that this target category is currently

"Discriminated Out."

X. Press the MODE touchpad again.(*)

The flashing arrow will now point

toward MID-RANGE.

XI. Wave all objects over the Search Coil

The Pull-Tab and Zinc Penny will not

be detected.

The other objects will be detected

with their own distinctive tones.

XII. Toggle modes by pressing the MODE

touchpad again.(*)

a. Press once to see the current discrimination status of the detector

(Mid-Range Eliminated).

b. Then press again to toggle to the third discrimination setting.

i. Iron is eliminated.

ii. Mid-Range Metals are eliminated.

iii. Only high-tone metals like silver and copper will be detected.

(*)Note: The mode status will flash for 10 seconds. After 10 seconds,

mode status will time-out and stop flashing.

QUICK-START DEMONSTRATION(continued)

BASIC OPERATION

POWERING UP

Press the ON touchpad.

All display indicators will illuminate momentarily.

The 4-segment pyramid-shaped Sensitivity Indicator will illuminate on

the left side of the display. The 4-segment pyramid indicates that the

detector is at full sensitivity.

When an object is detected, the object will be identified by a tone, a

display indicator, and a depth indication.

A two-minute “warm-up” is required before the detector reaches full

sensitivity.

UNDERSTANDING THE DISPLAY

The LEFT SIDE of the display has a dual purpose:

●

1SENSITIVITY LEVEL

Upon power-up, and after

pressing either the up- or

down-sensitivity pads, the

pyramid-shaped display

indicates the detector’s

sensitivity level.

The sensitivity level can be

changed using the up- and down-pads.

At maximum sensitivity, the unit can detect a coin-sized metal object

buried about 6" beneath the surface; larger objects can be detected

much deeper.

●

2DEPTH INDICATION

After detecting an object, the

pyramid-shaped display

indicates the approximate depth

of buried, coin-sized objects.

Objects at or near the surface

will illuminate the single

segment at the top of the

scale.

More deeply buried objects will illuminate more segments, indicating

depths of 2, 4, or 6 inches, as identified to the left of the display.

The depth indicator is not accurate for large, or irregularly shaped, objects.

However, the scale will provide relative depth indications for larger objects; a

given object will induce deeper readings the farther it is from the search coil.

BASIC OPERATION

(continued)

Discrimination Settings are as follows:

Mode Metals Status Display

Eliminated Tones (During discrimination selection)

No Target

All-Metal None High Indicators

Flashing

Iron Ferrous Low Iron

Discrimination only Indicator

Flashing

Pull-tabs, Screw

Mid-Range Caps, some Foil, Mid-Range

Discrimination medium Gold, Medium Indicator

Zinc, Nickels Flashing

Full Ferrous and Low & Iron and

Discrimination Mid-Range Medium Mid-Range

metals Indicators

Flashing

USING HEADPHONES

Using headphones (not included) improves battery life, and prevents the

sounds from annoying bystanders.

It also allows you to hear subtle changes in the sound more clearly,

particularly if searching in a noisy location. For safety reasons, do not use

headphones near traffic or where other dangers are present. This device is

to be used with interconnecting cables/headphone cables shorter than three

meters.

10 11

BASIC OPERATION

(continued)

BASIC OPERATION

(continued)

The RIGHT SIDE of the display classifies objects into three categories.

Silver/Copper: ------------------------------------------

Objects composed of silver and

cooper will illuminate this arrow.

Buried and heavily oxidized metal

objects, such as old tin cans, can

also fall into this category. Larger

aluminum objects, like beverage

cans, will sometimes fall into this

category.

Mid-Range: ------------------------------------------------

Mid-range objects cover a large

variety of metals.

Among them are: pull-tabs from

beverage containers, nickels,

medium-sized gold objects, some

types of aluminum, and zinc.

Iron: -------------------------------------------------------------

All ferrous objects, and some

smaller aluminum objects, fall into

the iron category. Small gold

objects can also fall into this range.

The BOTTOM RIGHT SIDE of the

display will illuminate a Low Battery

Indicator symbol if the batteries are

discharged. The indicator illuminates,

and remains illuminated, when the

9-volt batteries have discharged to a

level of 7.35 volts.

Reading the Display IN THE FIELD

With the detector in use in the field, the display will indicate both the DEPTH

and the TARGET IDENTIFICATION of each object detected. After a target is

detected, these indicators will remain illuminated with this information until

the next target has been detected. If uncertain about the target’s

identification, try sweeping the coil at a faster speed. A more rapid sweep

over a target will generally provide a more accurate target identification.

The MODE CONTROL

The MODE touchpad allows for the elimination from detection of

unwanted metal objects.

By pressing MODE, the user toggles among four different discrimination

settings.

During MODE (or discrimination) selection, the SENSITIVITY INDICATOR

on the left of the display will flash continually. The detector will remain

in this discrimination selection mode for 10 seconds until a metal object

has been detected.

If an object is detected during mode selection, the detector will

exit mode selection. If this happens, you will need to press

MODE again and begin mode selection over again. To avoid this,

keep the detector stationary and reduce sensitivity before

pressing MODE.

The MODE touchpad has two functions:

Each first press of MODE will be followed by.

●

1A distinctive tone or tones, indication the detector’s stored

discriminating setting.

HIGH TONE - no object eliminated.

LOW TONE - iron eliminated.

MEDIUM TONE - mid-range metals eliminated.

LOW & MEDIUM TONE - irons and mid-range metals

both eliminated.

●

2Flashing target and sensitivity indicators. The flashing target

indicators point to the targets eliminated.

Each subsequent press of MODE will toggle between discrimination settings.

The flashing arrow indicates the target category eliminated.

The detector will store the current discrimination setting until the power

is turned off.

Altri manuali per Outback

Indice

Altri manuali Bounty Hunter Rilevatore di metalli

Bounty Hunter

Bounty Hunter Land Ranger PRO Manuale utente

Bounty Hunter

Bounty Hunter HandyMan Manuale utente

Bounty Hunter

Bounty Hunter Tracker I Manuale utente

Bounty Hunter

Bounty Hunter Tracker IV Manuale utente

Bounty Hunter

Bounty Hunter Quick Silver Manuale utente

Bounty Hunter

Bounty Hunter Platinum Manuale utente

Bounty Hunter

Bounty Hunter Land Star Manuale utente

Bounty Hunter

Bounty Hunter Junior Manuale utente

Bounty Hunter

Bounty Hunter PIONEER EX Manuale utente

Bounty Hunter

Bounty Hunter Quick Silve Manuale utente

Bounty Hunter

Bounty Hunter Quick Draw Pro Manuale utente

Bounty Hunter

Bounty Hunter Fast Tracker Manuale utente

Bounty Hunter

Bounty Hunter DISCOVERY 1100 Manuale utente

Bounty Hunter

Bounty Hunter Ultra Mag Sharp Shooter Manuale utente

Bounty Hunter

Bounty Hunter Gold Manuale utente

Bounty Hunter

Bounty Hunter Snooper 2 Manuale utente

Bounty Hunter

Bounty Hunter Fortune Hunter Manuale utente

Bounty Hunter

Bounty Hunter Quick Praw II Manuale utente

Bounty Hunter

Bounty Hunter Tracker II Manuale utente

Bounty Hunter

Bounty Hunter Pilot Manuale utente

Bounty Hunter

Bounty Hunter Tracker II Manuale utente

Bounty Hunter

Bounty Hunter Platinum Manuale utente

Bounty Hunter

Bounty Hunter PINPOINTER Manuale utente

Bounty Hunter

Bounty Hunter Tracker IV Manuale utente

Manuali Rilevatore di metalli popolari di altre marche

Garrett

Garrett MAGNASCANNER CS 5000 Manuale utente

Valex

Valex 1800200 Manuale utente

Gauss

Gauss MIL MD Manuale utente

Velleman

Velleman CS130 Manuale utente

Sears

Sears 321.596370 Manuale utente

Eriez

Eriez X8 Manuale utente

Steinberg Systems

Steinberg Systems SBS-MD-22 Manuale utente

Zircon

Zircon MetalliScanner m60c Manuale utente

nalanda

nalanda MD027 Manuale utente

REV Ritter

REV Ritter CB-7005 Manuale utente

Minelab

Minelab F1A4 Manuale utente

Fisher Research Labs

Fisher Research Labs F70 Manuale utente

Steinberg Systems

Steinberg Systems SBS-MD-12 Manuale utente

GOLDEN MASK

GOLDEN MASK 5 Manuale utente

Grizzly

Grizzly YM 203 Manuale utente

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manuale utente

Treasure Cove

Treasure Cove Vibra-Probe 560 Manuale utente

Accurate Locators

Accurate Locators XL16 IMAGER Manuale utente