Boyo Vision VTBSD1 Manuale utente
MICROWAVE RADAR BLIND
SPOT DETECTION SYSTEM
User’s Manual
VTBSD1
Version：V1.0
Catalog
I. Components....................................................................................... 1
II. System Specification........................................................................ 2
III. Install Caution................................................................................ 3
IV. Requirements for Radar Sensor Setting.................................... 3
V. Installation Diagram.......................................................................... 3
VI. Wires Connection Diagram.......................................................... 4
VII. Installation Gist.............................................................................. 5
VIII. Parts Recovery............................................................................ 11
IX. Operation Instruction.................................................................. 11
X. Usual malfunction elimination........................................................13
1
Foreword
Thanks for using our BSD system. The System is designed for
universal cars, please read this product manual carefully for
installing and uninstalling the product.
I. Components
NO.
ITEM
QTY
PICTURE
1
Main harness
1PCS
2
Sensor
2PCS
3
LED indicator
2PCS
4
Buzzer
1PCS
5
Instruction
manual
1PCS
6
Cable tie
A dozen
Tools for angle calibration: tape, ruler, angle calibration cloth,
marker pen, magnet
Tools for installing and uninstalling: plastic pry, alcohol, cleaning
cloth, insulated tape, multi-meter, screwdriver
2
II. System Specification
NO.
Item
Specification
1
System Configuration
2pcs Radar Sensors
2pcs LED Indicator lights
1pcs Buzzer
2
Compliance
ISO17387:2008
3
Detection Rang Accuracy
±0.25m（Typical)
4
Max. Detection Range
Truck：0.3m～15m;
Car ：0.3m～15m;
Motorcycle ：0.3m～10m;
Pedestrian：0.3m～7m;
5
Alert Range
0.3m~15m
6
System
Alert Accuracy
Car：≥98%
Motorcycle：≥95%
Pedestrian：≥95%
7
HMI(Human Machine
Interface）
Level 1:LED Stay lit
Level 2:LED Blink+ Beep Sound
8
IP Rating
IP6K7K
9
Power Consumption
≤ 100mA ＠12VDC
10
Operation voltage
12V
11
Operation Temperature
-40℃～+85℃
12
Storage Temperature
-40℃～+95℃
3
III. Install Caution
1. Please release negative power before operation.
2. Do not pull the harness when removing the connector, insert the
connector to the buckle until a sound.
3. Harness should be fixed with car harness by cable tie.
The installation and disassembly should follow the vehicle
maintenance manual and relative operating instruction. Avoid
breaking any components of the car, replace the corresponding parts
immediately should there is any broken component.
IV.Requirements for Radar Sensor Setting
1. Radar sensor can only penetrate plastic object (bumper shell).
2. Radar sensor should not be interfered by metal objects.
3. Do not install the radar sensor against fluorescent lamps.
V. Installation Diagram
4
VI.Wires Connection Diagram
1. BSD_L connect to left sensor of BSD
2. BSD_R connect to right sensor of BSD
3. LED_L connect to Left LED indicator
4. LED_R connect to right LED indicator
5. L_Lamp connect to left rear lamp (left turn light)
6. R_Lamp connect to right rear lamp (right turn light)
7. Buzzer connect to buzzer
8. Speed connect to vehicle speed signal (reserved)
9. +12v connect to ACC connector
10. GND connect to Vehicle GND wire
5
VII. Installation Gist
1. Sensor settings
Step1. Sensors of the BSD system should be pasted to both inner
corners of rear bumper shell with an angle of 25°to 35°, at height of
35-90cm.(Fig.1-Fig.3).
Fig.1~Fig.3
Step2. Place a straight tape between front wheel and rear wheel,
then place a 30ºangle calibration cloth under the rear bumper, the
cloth edge should be paralleled with the tape (Fig.4).
Step3. Place a ruler (about80cm) vertically, one side of the ruler
should be leaned on the rear bumper, the other side of the ruler
should be paralleled with the calibrating lines on calibration cloth
(Fig.5-Fig.6).
6
Fig.4-Fig.6
Step4. Mark down the position ruler against the bumper with a
marker (Fig.7-Fig.9).
Fig. 7 Fig. 8 Fig. 9
7
Step5. Mark down the position with same method for the other side
of bumper (Fig.10).
Fig. 10
Step6. Take off the plastic rear bumper (be aware of scratching on
the bumper)(Fig.11-Fig.12).
Fig. 11 Fig. 12
Step7. Clean the installation location of sensor with alcohol
(Fig.13-Fig.14).
Fig. 13 Fig. 14
8
Step8. Prepare 2 pieces of magnetic metal; place one on the line
marker outside the bumper and the other one on the corresponding
spot inside of it. Mark the location with the marker. (Fig.15-Fig.17)
Fig.15 Fig. 16 Fig. 17
Step9. Clean the plastic surface of the sensor with alcohol and then
place a 3M adherent tape on the sensor (Fig.18-Fig.19).
Step10. Stick the sensor to the location of Fig.17 (Step.8). Place the
terminal wires of the sensors upward vertically. (Fig.22)
Step11. Install the sensor on the other side with same method
Fig.18 Fig.19 Fig.20
Indice
