B+B SmartWorx SmartSwarm 342 Istruzioni operative e di manutenzione

QUICK START GUIDE

1. Introduction

The SmartSwarm™342 IIoT Gateway provides configuration management, data

aggregation, filtering and business logic for data recovered from a mesh-network of

connected WZZARD™MESH wireless nodes.

Safety

• Use the device in compliance with national and international law and in compliance with

any special or additional restrictions regulating use of the Advantech B+B SmartWorx

device in specific applications and environments.

• Use only the original accessories as provided by Advantech B+B SmartWorx. Using

unapproved accessories can result in device damage, warranty termination, and/or

violation of legal regulations.

• Unauthorized device or accessory modification can result in device damage, warranty

termination, and/or violation of legal regulations.

• Do not open the device.

• When connecting the device to a power supply, do not exceed the defined voltage.

• Do not expose the device to extreme ambient conditions. Protect the device against

dust, moisture and high temperature.

Hereby, Advantech B+B SmartWorx s.r.o. declares that the radio equipment type

SmartSwarm SG300 (versions with radio interface only), SG303, SG305 is in compliance

with Directive 2014/53/EU. SmartSwarm SG300 versions without radio interfaces are

in compliance with the essential requirements and other relevant provisions of Directives

2014/30/EU and 2014/35/EU.

The full text of the EU Declaration of Conformity is available at the following internet

address: www.advantech-bb.com/eudoc

SmartSwarm 342

Quick Start Guide

QUICK START GUIDE

Product Disposal

The WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive

has been introduced to ensure that electrical/electronic products are recycled

using the best available recovery techniques to minimize the impact on the

environment. This product contains high quality materials and components

which can be recycled. At the end of its life this product MUST NOT be

mixed with other commercial waste for disposal. Check with the terms and

conditions of your supplier for disposal information.

Declarations of Conformity

These products are in conformity with the provisions of the following directives

when used in accordance with the instructions contained in the product

documentation.

2014/35/EU Low Voltage Directive

2014/53/EU Radio Equipment Directive

2011/65/EU Reduction of Hazardous Substances Directive

2012/19/EU Waste Electrical and Electronic Equipment (WEEE) Directive

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may

cause undesired operation.

Canadian Compliance Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus as set out in the Radio Interference Regulation of the Canadian

Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la class B prescrites dans le Règlement

sur le brouillage radioélectrique édicté par le ministère des Communications du

Canada.”

QUICK START GUIDE

2. Connect Antennas

Connect a 2.4GHz antenna to the connector marked “MESH.”

If required, and if you have a cellular enabled version of SmartSwarm 342, connect the

main cellular antennas to the device by screwing them into the ANT and DIV connectors.

3. Install SIM Card

If you intend to use this device to communicate over a cellular network, place an activated

data-provisioned SIM card into the SIM1 card reader.

NOTE: SIM2 is not currently supported.

4. Connect Power

The device requires between +10 to +60V DC power. 4W typical; 11 W peak.

5. Connect Ethernet

An Ethernet cable may be connected to the ETH0, and/or ETH1, connector/s on the front

panel. By default, the Ethernet ports are configured as follows:

PORT PURPOSE DEFAULT SETTING

ETH0

LAN port (default)

Connect your laptop or PC to get a local web-server

for device configuration and diagnostics.

DHCP Server

IP Address: 192.168.1.1

NetMask: 255.255.255.0

ETH1

WAN port (default)

Connect this port to your WAN to allow the device

to obtain access to the remote device management

service, SmartWorx Hub, over Ethernet.

DHCP Client:

The device will automatically

obtain an IP address from your

DHCP server.

QUICK START GUIDE

6. Configuration

By default, the device will make a secure connection to the cloud-hosted device

management service: SmartWorx Hub https://hub.bb-smartworx.com

This will automatically happen if there is an outbound WAN connection available via ETH1,

with a route to the public Internet.

ALTERNATIVELY, you may want to use cellular. This requires a valid SIM card in SIM Slot 1.

In order to configure the cellular connection, connect your laptop or PC directly into ETH0,

then point your web browser at: 192.168.1.1.

You will be prompted to sign in. The default password is “5mart5warm”.

We recommend that you change this default password after you login for the first time.

Enter the APN name and optional credentials, as required by your SIM card provider /

network operator.

The WAN LED will turn ON (yellow) when the cellular connection has been successfully

established.

QUICK START GUIDE

7. Remote Configuration Using SmartWorx Hub

The USR LED will turn on (yellow) when the device successfully makes a secure

connection with SmartWorx Hub https://hub.bb-smartworx.com.

The SmartSwarm 342, and all of the connected WZZARD MESH wireless sensor nodes,

can be configured remotely via the SmartWorx Hub cloud-hosted device management

service. To access this service, go to: https://hub.bb-smartworx.com

If this is your first time accessing this service, you will need a SmartWorx Hub account.

If you do not have an account, you may create an account for yourself, using the “Create

Account“ option available on the login page at: https://hub.bb-smartworx.com

If you have an account, please login to claim and manage your devices. By selecting the

“Devices/View Devices“ screen we can see that the device is available, and that it is

currently online.

QUICK START GUIDE

7.1 Claim Your SmartSwarm Device

Go to the “Devices’->’Claim Device” page to bring your new SmartSwarm device into

your Managed Device Farm on SmartWorx Hub.

Type in the entire Device-ID or Serial Number (this is written both on the device itself and

on the box that you took your device out of).

Enter the entire MAC address (this is written both on the device itself and on the box that

you took your device out of), then select “Check Device ID” to check that your device is

available to be claimed by you. Assuming it is, then select “Claim Device” .

If this process fails, carefully re-enter the information indicated above. Be very careful

not to confuse ‘8’ & ‘B’ or ‘0’ & ‘D’/‘C’. If the process still fails, please contact B+B

SmartWorx technical support.

Your device is now available for you to manage.

By selecting the “Devices/View Devices” screen we can see that the device is available,

and that it is currently On-line.

In order to fully verify the installation, please check that the device is shown as “Online”

in SmartWorx Hub:

QUICK START GUIDE

8. WZZARD Mesh

There is no configuration required for Wzzard Mesh wireless sensor nodes to join the

SmartSwarm 342 IoT Gateway.

Any available Wzzard Mesh wireless sensor nodes that are powered on, and in close

proximity to the Gateway, will be automatically discovered.

They will automatically appear on SmartWorx Hub, in the Manage Device -> Wzzard

Mesh UI.

Please refer to the Wzzard Mesh documentation for further information.

9. Factory Defaults

The unit may be reset to Factory Defaults at any time by pressing the Reset button on the

back-panel of the device for more than 10 seconds.

10. Additional Documents

The User Manual for the SmartSwarm 342 can be found on the company web site:

http://advantech-bb.com/product-technology/iot-and-network-edge-platforms/

smartswarm

QUICK START GUIDE

Worldwide Headquarters

ADVANTECH

No.1, Alley20, Lane26, Rueiguang Road

Neihu District, Taipei 11491

Taiwan, R.O.C

Phone: 0800-777-111

www.advantech.com

European Headquarters

Oranmore, Co. Galway, Ireland

Phone: +353 91 792444

Fax: +353 91 792445

[email protected]

Corporate Headquarters

707 Dayton Road

Ottawa, IL 61350 USA

Phone: 1-815-433-5100

Fax: 1-815-433-5109

[email protected]

www.advantech-bb.com

Middle East, UAE, Africa

AG Silver Tower, JLT, P.O. Box 48777

Dubai, UAE

Mobile: +971 50 943 65 62

[email protected]

Czech Republic Product Group

Sokolská 71 562 04 Ústí nad Orlicí,

Czech Republic

Phone: +420 465 521 020

Fax: +420 464 647 299

[email protected]

Latin America, Carribean

Phone: 1-727-797-0300

Cell: 1-727-480-5920

[email protected]

OEM & Product Modiﬁcation

Phone: 815-433-5222

Fax: 815-433-5104

Attn: Custom Dept.

[email protected]

Custom Quote Request Form:

www.advantech-bb.com/custom

SmartSwarm-342_4317qsg

11. LEDs

LED COLOR STATE DESCRIPTION

PWR Green

Off No power

On Device is booting

Blinking Device is in normal operating mode

Fast Blinking Device is updating firmware. Do not power off

USR Yellow

Off The device does not have a working session established with

SmartWorx Hub

On The device has a working secure session established with

SmartWorx Hub

PoE n/a n/a Not used

Mesh

Status Yellow

Off The WZZARD Mesh App on the Gateway is either not installed

or not running.

On The WZZARD ”App is installed and running.

Blinking There is communication in progress on the DUST mesh network

DAT Red

Off There is no communication on the cellular interface at this

moment

Blinking There is communication in progress on the cellular interface

SIM Green Off Reset button pressed or the device is booting

On Ready for operation. SIM 1 is enabled

WAN Yellow

Off There is no cellular connection between the Gateway and the

cellular service provider

On A cellular connection has been successfully established between

the Gateway and the cellular service provider

IN0 Green Off The default state

On Binary input no. 0 is active (user defined)

IN1 Green Off The default state

On Binary input no. 1 is active (user defined)

Out Yellow Off The default state

On Binary output is active (user defined)

ETH0

ETH1 Green On 10 Mb/s

Off 100 Mb/s

ETH0

ETH1 Yellow

On The network cable is not connected

Off Network cable is connected

Blinking Data transmission in progress

Indice

Altri manuali B+B SmartWorx Portale

B+B SmartWorx

B+B SmartWorx MESR424D Manuale utente

B+B SmartWorx

B+B SmartWorx SmartSwarm 300 Manuale utente

B+B SmartWorx

B+B SmartWorx MESR321 series Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente