Brave BRSG105K Manuale utente
BRSG105K
STUMP GRINDER OWNER’S MANUAL
1-800-350-8739
WWW.BRAVEPRODUCTS.COM
20195 S. DIAMOND LAKE RD, SUITE 100, ROGERS, MN 55374
MBRSG105K
Place serial tag here
MODEL: BRSG105K
Your Brave grinder is intended for outdoor-use only and can be used to remove many tree stumps and
exposed root systems 9” high or lower to ground level. Approach the stump from the top, cutting straight down.
Raise up out of the cut, move over in the desired direction, plunge again. Repeat these steps across the entire
stump. Make sure you completely read and understand this manual before using the grinder for the first time.
WARNING
READ and UNDERSTAND this manual completely before using the grinder! Failure to properly operate,
and maintain this grinder could result in serious injury or death to the operator or bystanders.
All machines have hazards associated with their operation. This stump grinder has certain special hazards,
which you must be aware of. As an operator or owner you have a duty to be aware of these hazards and know
preventive measures to take to avoid them. When reading this manual pay particular attention to avoiding these
hazards.
In particular, be aware of the following:
• Know location of buried electrical and other utility lines.
• Do not allow children or untrained adults to operate.
• Wear eye protection and other personal protection against flying rocks and debris.
• Check that cutter wheel teeth are secured, sharp and not missing.
• Do not operate if tethered safety switch fails to stop engine when released away/pulled.
• Make sure no children or bystanders are within 75 feet (23 meters) of stump grinding operation.
• Protect cars, windows and other objects within 75 feet (23 meters) from flying debris.
• Be prepared for machine “kickback” when initially contacting the stump.
• Be aware of potential for carbon monoxide (CO) poisoning.
• Prevent fires/explosions from fueling.
• Do not attempt to perform adjustments, declog or clean unit while engine is running.
• Avoid burns from engine or hot exhaust.
• Avoid using in wet or icy conditions where falls may occur.
• Check all hardware is tight before operation.
• Clean area free from all rocks and stones.
Details about these hazards are found throughout the manual and are summarized at the end of the manual under
“Important Safety Information.”
STOP!
ADD ENGINE OIL & FUEL: Your stump grinder requires assembly and that you add
engine oil to crankcase, fuel to tank. Review all assembly instructions prior to assembly.
INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged. See the
“Receiving Your Unit” section for instructions on whom to contact to report missing or damaged parts.
2 | BRSG105K REV A
TABLE OF CONTENTS
SECTION I: ASSEMBLY ............................................................3
STEP 1: INSPECT THE PACKAGING......................................................4
STEP 2: WHEELS & AXLE ..............................................................5
STEP 3: HANDLE TOWER ..............................................................6
STEP 4: THROTTLE ...................................................................7
STEP 5: HANDLE & WIRING CONNECTORS ..............................................8
SECTION II: SAFETY & OPERATION .................................................9
YOUR KOHLER ENGINE ..............................................................10
SAFE PRACTICES & GENERAL INFORMATION ...........................................11
QUICK START & TROUBLESHOOTING .................................................12
ADJUSTING THE DRIVE BELTS ........................................................13
TETHERED SAFETY SWITCH .......................................................... 14
SUMMARY OF GENERAL SAFETY INFORMATION .......................................15
SECTION III: PARTS & SCHEMATICS ................................................19
SCHEMATICS .......................................................................20
PARTS LIST .........................................................................21
WARRANTY.........................................................................22
WARRANTY REGISTRATION FORM ....................................................23
ENGLISH
SECTION I
ASSEMBLY
4 | BRSG105K REV A
ASSEMBLY
CHECK THE PACKAGING
STEP 1: INSPECT THE PACKAGING
Open and unpack all items. Leave lots of working space. Inspect all parts.
The Stump Grinder is shipped in a crate. Leave the sides folded down and use as your work
space.
NOTE: Upon inspection of parts, if you find any damage or missing parts please call BRAVE
at 1 (800) 350-8739 or contact us via our website at www.braveproducts.com. We will
replace any damaged or missing parts to you for free. Please do not return to the store.
ENGLISH
BRSG105K REV A | 5
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 2: WHEELS & AXLE
1. Slide wheels on to the axle and install the lynch pins.
2. For pivot grinding, insert the pin through the wheel hub and axle to inhibit movement of
desired wheel.
3. Pin only the axle to allow the wheel to spin freely.
4. During transport in trailer or pickup, pin both wheels for dual wheel brakes.
5. Install axle on to frame with two bolts and hardware provided.
PIN FOR FREE ROLLING
BOLT AXLE TO FRAME
PIN HOLE FOR WHEEL BRAKE
ENGLISH
6 | BRSG105K REV A
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 3: HANDLE TOWER
1. Mount the handle tower with the bolts provided.
2. Connect the two wire connectors.
1
2
ENGLISH
BRSG105K REV A | 7
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 4: THROTTLE
Note: Throttle tension adjustment nut. Tighten if throttle becomes loose
THROTTLE TENSION
ADJUSTMENT NUT
ENGLISH
8 | BRSG105K REV A
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 5: HANDLE & WIRING CONNECTORS
1. Install the bow handle with the long bolt.
2. Connect the wiring connectors.
1
2
ENGLISH
SECTION II
SAFETY & OPERATION
10 | BRSG105K REV A
SAFETY & OPERATION
YOUR KOHLER ENGINE
Read the Kohler engine manual supplied with your unit for full engine operation, safety, and
maintenance instruction.
1Air Filter - Summer and Winter Positions
2Gas - Use Mid Grade or Higher
3Choke - Left is On / Right is O (Run Position)
4Gas On / O Switch - Left is O / Right is On
5Pull Starter - Pull Tight - Then Pull Start
6Oil - Fill to mark 10W30, will not start if oil is low, has low oil shuto
protection. Two yellow caps are oil fill caps, use either one to fill oil.
2
1
3
4
5
6
ENGLISH
Indice
