BREL BZE45 Manuale utente

Pagina 1

Manual Brel special bi-directional zipscreen motor

Type BZE45

Read the manual be ore you begin the installation. I these instructions are not ollowed,

this may lead to de ects and injury in which warranty can’t be claimed.

warning:

Children cannot recognize the dangers of electrical equipment and may therefore not work with it.

It is important to ollow this instruction or your own sa ety.

1. Do not operate the motor in humid surroundings.

2. The motor must be installed correctly.

3. eep the antenna in a good condition and do not shorten.

The antenna should not come into contact with other metal

parts otherwise it will reduce the effect.

4. The motor must be protected from direct moisture influences.

5. BREL-Motors declares that this motor has been manufactured according to the guidelines of the CE standard 1999/5/EC.

_______________________________________________________________________________

Wiring

_______________________________________________________________________________

Functions remote control Changing batteries

DD-2702H

Works with all BREL transmitters:

Always check that the remote control is in Bi-directional mode!

Re er to manuals or remote controls at

www.brel-motors.nl

_______________________________________________________________________________

Technical data o the motor BZE45-20 BZE45-40

NOTE:

I the motor has been running continuously

or 4 minutes, it may become too hot and

then stop. A ter approximately one hour

hal an hour, this one will continue to run.

Page 2

_______________________________________________________________________________

Step 1 Setting up the irst remote/channel

Tension motor 







 STOP until 2x 









Put tension on the motor, the product Press and hold the STOP button until the Transmitter/channel

moves up and down. The motor beeps. product moves 2x up and down and beeps 3x. has been set.

I NO end positions are set, the product will move in the pulse / step operation. Go to STEP 2.

I end positions are set, the product will continue go to its end position. Go to STEP 4.

NOTE: It is possible that the correct end positions have NOT been set. Go to OPTION A manual adjustment

or go to OPTION B and then to STEP 3A to automatically set the end positions.

______________________________________________________________________________

Step 2 Adjusting the direction o rotation(Only i the direction o rotation is not correct)

Only possible i no end positions are set, otherwise irst option B (Delete end positions), a ter that, Step 2.

▲+▼ until 1x 









Press UP and DOWN button The direction of rotation of

simultaneously, until the product moves. the motor is OK.

_______________________________________________________________________________

Step 3A Automatically setting the end position

I no end positions have been set, the motor only moves in pulse mode.

▲ 



 





Press the UP button, until the product moves to The product automatically goes The top- and down-

the desired top position and stops at resistance. down and stops in case of resistance. position is set.

When the roller shutter has been up and down 50 times, the motor checks the end positions and adjusts them i necessary.

_______________________________________________________________________________

Step 3B Manually setting the end position.

I no end positions have been set, the motor only moves in pulse mode.

1. Set the desired top position.

▲+ STOP Press and hold until 2x 









Go with the OPERATING- Press and hold the STOP and UP button until The desired topposition is set.

buttons to the desired topposition. the motor moves up and down 2x and beeps 3x.

Page 3

2. Set the desired down position.





 STOP+▼ 2x 









Go with the OPERATING- Press and hold the STOP and DOWN button until The desired downposition is set.

buttons to the desired the motor moves up and down 2x and beeps 3x.

downposition.

_______________________________________________________________________________

Step 4 Setting the desired third limit position (I desired)





 1x P2 1x 







 1x STOP 1x 







 1x STOP 2x 









Set the desired Press 1x P2. Press 1x STOP button. Press 1x STOP button.

Third limit The product moves 1x The product moves 1x The product moves 2x up

position. up and down and beeps. up and down and beeps. and down and beeps 3x for confirmation.

Press and hold STOP or 3 seconds to move to the set limit position.

______________________________________________________________________________

Additional settings

____________________________________________________________________________

Option A Adjusting the top position

I adjustment is not possible, go to Option B, then to Step 3.





 STOP +▲ until 







 



 STOP +▲ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set top position. STOP and UP until top position. STOP and UP button, until

the motor moves and beeps 1x. the motor 2x moves and 3x beeps.

___________________________________________________________________________

Adjusting the down position

I adjustment is not possible, go to Option B, then to Step 3.





 STOP +▼ until 







 



 STOP +▼ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set bottom position, STOP and DOWN until bottom position. STOP and DOWN button, until

the motor moves and beeps 1x. the motor 2x moves and 3x beeps.

______________________________________________________________________________

Option B Deleting the end limits

1x P2 1x 







 1x ▼ 1x 







 1x P2 2x 









Press 1x P2. The product Press the DOWN button. Press P2. The product The end positions

moves up down and beeps 1x. The product moves 1x moves 2x up and down are now deleted

up and down and beeps 1x. and beeps 1x. from the memory.

Page 4

_______________________________________________________________________________

Option C Deleting the third limit position

1x P2 1x 







 1x STOP 1x 







 1x STOP 1x 









Press 1x P2. Press 1x STOP button. Press 1x STOP button.

The product moves 1x up The product moves 1x up The product moves 1x up and

and down and beeps 1x. and down and beeps 1x. down and beeps 1x for confirmation.

_______________________________________________________________________________

Option D Learn new transmitter/channel while maintaining end limits.

Only possible when end limits are set.

= Already existing transmitter = New transmitter

Method 1

P2 a until 







 P2 a until 







 STOP b until 2x 









Press P2 of a. The product Press P2 o a. The product Press STOP o b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps 3x.

Repeating the above will remove the new transmitter/channel.

Method 2 (also sun- and windmeter)

P2 a until 







 P2 a until 







 P2 b until 2x 









Press P2 o a. The product Press P2 o a. The product Press P2 o b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps 3x.

Repeating the above will remove the new transmitter/channel.

_______________________________________________________________________________

Optie E Pulse / jog control

1x 







, beeps 1x

▲+▼ until 1x 







 1x STOP

Pulse / jog on

Pulse / jog o

Press and hold UP and DOWN button, Press 1x STOP button.

until the product moves up and down.

2x 







 , beeps 3x

Page 5

______________________________________________________________________________

Option F Sun- and windmeter ( DD-116H )

_______________________________________________________________________________

Add / remove

1x P2a 1x 







 1x P2a 1x 







 1x P2b 2x 









The sun and wind meter has been added.

Press P2 o a. The product Press P2 o a. The Press P2 o b. The

moves 1x up and down and product moves 1x up product moves 2x up

beeps 1x. and down and beeps 1x. and down and beeps 3x.

By repeating the above, you can remove the sun and wind meter again.

_______________________________________________________________________________

On / o sun unction ( Factory setting = on)

1x P2 1x 







 1x P2 1x 







 1x ▲ 









ON: The product moves up and down once and beeps once long.

OFF: The product moves up and down 2x and beeps 3x long.

Press 1x P2. The product Press 1x P2. The Press 1x UP.

moves 1x up and down and product moves 1x up

beeps 1x. and down and beeps 1x.

By repeating the above, you can switch the sun unction on or o again.

Altri manuali BREL Motore

BREL

BREL BEQ35 Series Manuale utente

BREL

BREL BPE Manuale utente

BREL

BREL BRE45 Manuale utente

BREL

BREL BLE45-50 Manuale utente

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente