Brickstuff KIT18 Manuale utente
Lighting and Automation System
www.brickstuff.com ● Visit http://bit.ly/brickguides for expanded guides, idea books, and usage tips
INSTRUCTIONS FOR USE
Welcome, and Thank You!
Thank you for purchasing this Brickstuff product. We hope you enjoy using it as much as we enjoyed creating it. The
parts in this box are only part of our story, only part of what we’re working hard to develop. Our goal is to create the
most flexible and exciting line of hobby lighting and automation products for you to use in all of your fantastic creations.
All of these products will work together, and you won’t need to be an electronics expert to use them. So keep building
amazing things—we’ll help you bring them to life.
Thanks again for supporting us. We couldn’t do this without you!
#75827 Firehouse HQ Lighting Kit
This kit includes multiple lighting assemblies and other parts needed to light up your Firehouse Headquarters. The parts
are supplied in four different bags: three bags specific to each floor in the headquarters, and one bag with six ceiling lights
(used on multiple floors). Remove all bags from the box, and begin installing your lights starting with the first floor (bag
1). The following diagram shows how to install the lights and adapters on the first floor:
--- The Brickstuff Team
Mount both front lights, care-
fully running the wires up the
wall and between bricks.
Run the front light wires between studs— DO NOT PINCH
WIRES ON TOP OF STUDS. Carefully re-attach dark gray
tiles to secure wires in place.
Mount three ceiling lights, and coil the wires
around the middle assembly. Using the included sticky squares, mount the 9-port
adapter along the top of the wall, replace the alarm bell
light and connect it to the lighting effect controller,
mount the table lamp, mount the desk lamp, and mount
the slime LED (outside the building). Run all wires inside
and up the wall. Connect lights to the 9-port adapter.
Run the 6” black cable from
the leftmost connector on
the 9-port adapter, be-
tween the studs and out
the back of the top wall.
Cover wire with dark gray
tiles.
All lights should be con-
nected to the 9-port adapt-
er, with the exception of
the slime LED and the
alarm bell light. These
should be connected to the
effect controller. Connect
the effect controller to the
rightmost plug on the 9-
port adapter using the
black 1.5” cable.
LEGO® Ghostbusters Firehouse Headquarters (#75827) Product Guide (KIT18) v1.0, June 2016.
Small Lights for Big Ideas is a Registered Trademark of Enthusiast Enterprises, LLC. Brickstuff, QuicKit, BrickPixels, and the Lighting Gear Logo are trademarks of Enthusiast
Enterprises, LLC. This product is subject to the warranty and liability policy set forth in the Warranty section of our website, www.brickstuff.com. LEGO® is a trademark of the
LEGO Group of companies which does not sponsor, authorize or endorse any Brickstuff product or service.
The LEGO Group is not liable for any loss, injury, or damage arising from the use or misuse of this product.
Wiring The Second and Third Floors
Wiring for the second floor is completed on the
underside of the floor structure. See the master
connection diagram included with this kit for
specific connections. Use plates to hold excess
wiring in place.
This photo has one plate removed to show how
wiring for the table lamp in the bedroom on the
second floor was run between floor plates and
down to the underside of the floor. Take care
not to pinch wires between studs when running
wires.
Second floor (shown on its
side). To the left is the out-
bound wire for connecting to
the third floor. The adapter
board on the right is held in
place using one of the large
sticky squares provided with
this kit.
Run the 12” black connecting cable from under the floor up be-
hind the cabinets and out the top back of the second floor. This
wire will connect to the third floor.
Run the wire from the ceiling light around to the back area of the
cabinets (taking care to avoid pinching the wire on studs), then
down to the underside of the floor.
These photos show how to mount the three Pico LEDs on the second
floor. The first is mounted into the microwave oven, then connected
to the first output of the lighting effect controller underneath the
floor. Mount the second Pico LED inside the fireplace, then snap the
flame assembly on top of the LED. Connect the fireplace LED to the
second output of the lighting effect controller.
Stick the self-adhesive flashing LED inside the video game cabinet.
3rd Floor
Power In
2nd Floor
Power Out
2nd Floor
Power In
1st Floor
Power Out
Connect Ceiling
Lights and Ta-
ble Lamp to 4-
Port Adapter
Run 12”
Cable Out the
Top of the
Wall
See the Master Connecon Diagram Showing All Floors,
Lights, Wires, and Adapters for More Informaon About
How to Connect Parts
Third Floor Detail
Indice
Altri manuali Brickstuff Attrezzatura di illuminazione
