Briggs & Stratton VH-300 Manuale di istruzioni

"#$!%&'()!*++'!,-!

./0+12!*3!$456$!

7$8946$96555!

:::;(<=&0>)+?(0@+AB<1>;@+A!

OPERATING

& INSTRUCTION

MANUAL

VH-300 BRIGGS & STRATTON

VH-300 HONDA

IMPORTANT

RETAIN THIS MANUAL

C+D!?1(0DE@0?+1!+1!<((&AF'>!<1-!+B&D<0?+1!+=!G+?(0!

,.3H!IGJK!L3MN3O!P3,.CNOOQ!R,CS,.!3II.L*IJMT!IS!

3KK.LRO.!S,!S*.,3I.;!C3JON,.!IS!PSL*OQ!%JIG!!

JMKI,NPIJSMK!L3Q!P3NK.!IG.!GSJKI!IS!L3OCNMPIJSM!

3MH2!L3Q!,.KNOI!JM!*.,KSM3O!JMUN,Q;

!!!!Safety Hoist Company

Hoist Manual

Table of Contents

!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!Subject Page

!!!!!!!!!!!!!!!!!Every Time Set Up Instructions 1

General Safety Instructions 2

Safe Operating Procedure 3

Hoist Assembly 4

Hoist Operation 9

Transporting Hoist 14

Cautions 16

Hoist Parts, List 17

Optional Equipment 18

Engine Recommendations 19

Warranty, Limited Back Cover

I. EVERY TIME SET UP INSTRUCTIONS

***IMPORTANT***

EVERY TIME A SAFETY HOIST IS SET UP FOR OPERATION:

1.!CHECK OIL IN ENGINE AND GEAR BOX BEFORE STARTING ENGINE. REMEMBER

TO CHANGE THE OIL IN THE ENGINE AT LEAST EVERY 50 TO 100 HOURS

MAXIMUM.

2.!INSPECT WINCH DRUM AND BRAKE ASSEMBLY FOR OBVIOUS DAMAGE OR

MISALGMENT. INSPECT WINCH DRUM TO MAKE SURE THAT CABLE IS WOUND

SMOOTHLY WITH NO CROSSOVERS. IF THERE ARE ANY, RELEASE THE BRAKE

AND PULL OFF ENOUGH CABLE TO ELIMINATE THE CROSSOVERS. THEN WITH A

LEATHER GLOVE, CAREFULLY WIND THE CABLE BACK ONTO THE DRUM TO

PREVENT CABLE KINKING.

3.!INSPECT THE BRAKE BAND OR MULTISEGMENT BRAKE TO MAKE SURE IT’S IN

GOOD CONDITIONS WITH NO CUTS OR TEARS. MAKE SURE NO OIL OR MUD HAS

GOTTEN ONTO THE BRAKE ASSEMBLY WHICH WILL CAUSE THE BRAKE TO SLIP.

4.!TEST THE BRAKE. PUT ONE BUNDLE OF SHINGLES (OR ABOUT 70 TO 100

POUNDS) ON THE PLATFORM. ONLY LIFT IT TWO OR THREE FEET TO MAKE SURE

THE BRAKE IS CLEAN AND WORKING PROPERLY, AND THEN LOWER THE LOAD

SLOWLY. DO THIS AT LEAST SIX TIMES BEFORE TRYING TO LIFT A LOAD

HEAVIER THAN THE TEST LOAD. ONCE YOU ARE CERTAIN THE BRAKE WILL HOLD

THEN RAISE THE LOAD YOU ARE TRYING TO LIFT A FEW FEET.STOP RAISING

THE LOAD. WAIT A MINUTE TO MAKE SURE THE LOAD DOESN’T SLIP. THIS WILL

VERIFY THAT THE BRAKE IS WORKING PROPERLY FOR THE FULL LOAD WEIGHT.

!!II.GENERAL SAFETY INSRUCTIONS

A. These safety instructions and warnings are not substitutes for routine

prevention measures which must also be observed to avoid

potential risks and hazards. Failure to obey these safety warnings may

result in injury to you or others, or damage to the hoist.

1.!WARNING… DO NOT USE OR PLACE THIS METAL HOIST IN ANY AREA

WHERE IT COULD COME IN CONTACT WITH ELECTICAL WIRING OR

OTHER HAZARDS CAUSING INJURY OR DEATH!!!

2.!Avoid damage to Hoist operating parts by securing hoist to truck bed with cord

rope or bungee cord. Damaged parts MAY make hoist not SAFE to operate.

Note: Transporting hoist in rain may cause road oils to be deposited on brake

band and or brake pulley. Cover brake area with plastic sheet and inspect prior

to use. See Section III, How to Assemble your Hoist.

3.!When unpacking a new Hoist, inspect parts carefully for any damage that may

have occurred during transport. DO NOT ASSEMBLE OR USE THE HOIST IF ANY

PARTS ARE DAMAGED!! Return the damaged part to the place of purchase for

replacement.

4. Observed all labels and instructions attached to various parts of the Hoist.

5. For Safe Operation use only parts, attachments and accessories

supplied by the Manufacturer for use with this Hoist. Using substitute

parts will void the Warranty.

6.!Check assembled parts (splice plates, bolts, engine mounting, belts, pulleys,

hoist cable, etc.) for proper tightness and fit before using the Hoist, and during

frequent periods of use, be certain the equipment is in safe working condition.

Recheck for bolt tightness after every 4 hours of operation.

7.!Never place the Hoist on a slippery, uneven or unstable surface. Make sure the

Hoist is properly braced against a building or solid abutment at the correct angle

as described herein. Base of hoist should be one (1) foot away from the building

for every (4) four feet of building height. Top of hoist must be tied off for safety

operation. Tie to rungs not side rails.

8.!Keep the area around the base of the Hoist clear of debris to avoid

slipping, tripping or falling against the Hoist.

9. Handle fuel with care. It is extremely flammable and highly explosive

under certain conditions.

a.!Never smoke or allow open flames or sparks to be present in the vicinity of

the when the fuel tank is being filled.

b.!Use an approved fuel container

c.!Never add fuel to a hot or running engine.

d.!Replace fuel caps of the supply container and the engine fuel tank and wipe

up any spilled fuel before starting the engine.

B. SAFE OPERATION PROCEDURE

1.!DO NOT ALLOW ANYONE TO OPERATE THE HOIST WHO HAS NOT BEEN

PROPERLY AND THOROUGHLY TRAINED IN ITS OPERATION AND USE IN

ACCORDANCE WITH THIS HOIST’S INSTRUCTION MANUAL.

2.!NEVER OPERATE THE ENGINE INDOORS. EXHAUST FUMES CAN BE

HAZARDOUS IN ENCLOSED AREAS.

3.!ONLY USE THE HOIST TO LIFT MATERIALS!!!! THE HOIST SHOULD NEVER BE

USED TO TRANSPORT A PERSON FROM ONE ELEVATION TO ANOTHER!!!! DO

NOT USE HOIST FOR LOWERING ANYTHING.

4.!Always Observe Maximum Capacity of Hoist. Following Chart is your guide.

Hoist Series Number of Passes of Cable Capacity

MH123 Series 2 200 lbs.

VH-300 Series 2 300 lbs.

HD-400 Series 2 200 lbs.

HD-400 Series 4400 lbs.

5.!KEEP HANDS, FEET, OTHER BODY PARTS AND CLOTHING AWAY FROM THE

TRACK AND MOVING OR ROTATING PARTS OF THE HOIST WHEN STARTING

THE ENGINE OR OPERATING THE HOIST.

6. Do not allow any one to work or walk around or under the Hoist when in

operation.

7. Do not use the Hoist to lift buckets of hot asphalt or any other hot or liquid

substance, unless contents are in a closed and sealed container.

8. Always turn off the engine when you leave the vicinity of the Hoist.

III. HOW TO ASSEMBLE YOUR HOIST

1.!Unpack all parts of the hoist and lay them out on the ground.

MAJOR PARTS LIST

3-8ft. track sections with splice plate’s attached

1-VH Peak assembly

1-VH Carriage Flap (Flap Assembled on Carriage)

1-Carriage with 1/2” bolt, washers and lock nut (Bolt Assembled on Carriage)

1-Steel base section with winch drum, brake, cable and drive belt

1-Brake release handle with hitch pin

1-Power Pack (engine bolted on motor base)

Note that the engine is shipped without gas or oil. Oil needs to be added in the

crank case and the gear reduction unit, please refer to the instruction manual for

the engine for oil type and quantity.

2.!Prepare hoist assembly by standing base section on its side with Brake Drum UP

and Brake spring away from assembler.

3.!Slide an 8-ft. track section onto the base section with rung short side facing

towards assembler and secure each leg with two 3/8” carriage bolts and lock nuts.

Figure 1

Continue adding additional sections to reach the desired length of the hoist (See

Chart Page 7). The track sections are attached using the splice plates as noted

below with 3/8”x 3/4" carriage bolts and lock nuts. The splice plates must be

installed on the outside of the track section. See Figure 2

Figure'2'

4.!Lay the hoist down on the ground with the brake spring towards the ground.

5.!Slide the carriage onto the track section from the “Top” of hoist, with the flat

surface of the carriage facing away from the base section. See Figure 3

!!!Figure 3

6.!Slide the carriage along the track to base section so that the bumpers rest on the

base section. Make sure carriage slides smoothly on track.

7.!Slide the peak assembly (CH-B) onto the end of the track and secure it with two

(2) 3/8”x 3/4" carriage bolts and lock nuts. See Figure 4

Figure 4

!!!!!!!!!!

10. Slide the brake release handle over the brake bar and secure it with the hitch pin.

See Figure 5

!Figure 5

11. Turn the hoist up on its side with brake drum up.

12. Push forward on the brake handle to release the brake. (Note you will only need

to have it rotate 10-15 degrees, 1 – 2”, to release the brake).

13. While the brake is released, pull out cable from the winch drum. Draw out enough

cable to run up the back side of the track, thru the peak pulley and back down to

the carriage on the front side (The carriage side). See Figure 6

Figure 6

14.!Attach the thimble on the cable to the back of carriage using the 1/2" bolt, nut

and washers. Put 2 1/2" washers between thimble and carriage and 1 1/2"

washer on other side of thimble. Pass the bolt thru the washers, thimble and

then thru the bumper side angle then center hole on carriage. Tighten the 1/2"

bolt so it passes thru the nut, but not so tight as to stop the thimble from

rotating on the bolt. See Figure 7

Figure 7

Indice

Altri manuali Briggs & Stratton Motore

Briggs & Stratton

Briggs & Stratton 09000 Manuale utente

Briggs & Stratton

Briggs & Stratton 550 series Manuale utente

Briggs & Stratton

Briggs & Stratton 21A400 Series Guida all'installazione

Briggs & Stratton

Briggs & Stratton Sno/Gard 170400 Series Istruzioni per l'installazione

Briggs & Stratton

Briggs & Stratton 11B600 Manuale di installazione e funzionamento

Briggs & Stratton

Briggs & Stratton 330000 VERTICAL SERIES Manuale utente

Briggs & Stratton

Briggs & Stratton 130000 950 Series Manuale utente

Briggs & Stratton

Briggs & Stratton 210000 Series Manuale utente

Briggs & Stratton

Briggs & Stratton 080000 Manuale utente

Briggs & Stratton

Briggs & Stratton 430447 Manuale utente

Briggs & Stratton

Briggs & Stratton 120000 Manuale utente

Briggs & Stratton

Briggs & Stratton VANGUARD 810 EFI Istruzioni operative

Briggs & Stratton

Briggs & Stratton Vanguard 290000 Manuale utente

Briggs & Stratton

Briggs & Stratton 140000 Professional 1000 Series Manuale utente

Briggs & Stratton

Briggs & Stratton 90000 series Manuale utente

Briggs & Stratton

Briggs & Stratton 124T00 Series Guida all'installazione

Briggs & Stratton

Briggs & Stratton Vanguard 130000 Manuale utente

Briggs & Stratton

Briggs & Stratton 12K300 INTEK series Manuale

Briggs & Stratton

Briggs & Stratton 28N700 Series Manuale di installazione e funzionamento

Briggs & Stratton

Briggs & Stratton L824E Manuale utente

Briggs & Stratton

Briggs & Stratton 190000 Series Manuale di installazione e funzionamento

Briggs & Stratton

Briggs & Stratton 210400 Series Guida all'installazione

Briggs & Stratton

Briggs & Stratton Vanguard 470000 Series Manuale di installazione e funzionamento

Briggs & Stratton

Briggs & Stratton 272484 Manuale

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente