Brink Air for life Guida di riferimento

Wireless Controller with humidity sensor

English

Installation regulations

Contents

1 User manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Descripon Wireless Controller with humidity sensor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Delivery content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Technical specicaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 General product specicaon. . . . . . . . . . . . . . . . . . 6

2.2 Environment inuences. . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Overview operaonal controls. . . . . . . . . . . . . . . . . 7

3 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Mounng Wireless Controller with humidity sensor

on the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Remove Wireless Controller with humidity sensor

from wall bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.3 Connecng the AC/DC converter (opon). . . . . . . 10

3.4 Using another frame (opon). . . . . . . . . . . . . . . . . 12

4 Put into use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Connecng with USB Tranceiver (Pairing). . . . . . . 13

4.2 Back to factory seng Wireless Controller with

humidity sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5 Informaon addional Wireless Controller with humidity

sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1 Connecng addional RF sensor with USB Tranceiver

(Pairing). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.2 RH-sensor general. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.3 Sengs RH-sensor. . . . . . . . . . . . . . . . . . . . . . . . . . 17

6 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.1 General maintenance. . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 Replace baery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8 Troubleshoong and guarantee. . . . . . . . . . . . . . . . . . . . 21

8.1 Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 Conformity declaraon. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1 User manual

Dear client,

Thank you for buying the Wireless Controller with humidity sensor. This user’s manual contains all required

information to quickly become familiar with the product. We kindly request you to carefully go through this

information before using the product. This user’s manual is intended for the Wireless Controller with humidity

sensor installer and end user.

Take good care of this user’s manual! For more information or ordering manuals, please contact:

Brink Climate Systems B.V.

P.O. Box 11

NL-7950 AA, Staphorst, The Netherlands

T: +31 (0) 522 46 99 44

F. +31 (0) 522 46 94 00

E. info@brinkclimatesystems.nl

www.brinkclimatesystems.nl

1.1 Description Wireless Controller with humidity sensor

Intended and unintended use

This manual is about the Wireless Controller with humidity sensor (See C in image below).

The Wireless Controller with humidity sensor should only be used in combination with products that have been

approved by Brink Climate Systems B.V.

The Wireless Controller with humidity sensor can only be used with a HRU appliance which is equipped with a

USB connection! The Wireless Controller with humidity sensor is a wireless remote control to operate your

ventilation system. This remote control also displays when the ﬁlter(s) needs to be replaced/ cleaned or when the

ventilation system is malfunctioning. Brink supplies a range of wireless remote controls/sensors that make

contact with a heat recovery unit by means of a USB transceiver. This range consists of the 5 following types of

wireless controls/ sensors:

Wireless Controller

Wireless Controller with

build in CO

-sensor

Wireless Controller with

build in RH (humidity) -

sensor

Wireless CO

- sensor

Wireless Humidity - sensor

USB transceiver

Appliance with USB

connection (for example

HRU appliance type Flair)

Wireless Controller with humidity sensor 616880-B Brink / 3

The connected ventilation unit is operated by pressing one of the buttons on the Wireless Controller with humidity

sensor with your ﬁnger.

For explanation of the buttons of the Wireless Controller with humidity sensor see ®Overview operational

controls page 7.

The Wireless Controller with humidity sensor must always be used with a transceiver on the HRU appliance; a

combination of multiple remote controllers on 1 USB transceiver is possible.

In total, a maximum combination of 12 controllers /sensors can be connected to 1 transceiver (Max. 4

controllers / max. 4 CO2-sensors and max 4 humidity sensors).

Note: A controller with a build in CO2- sensor is seen as an CO2-sensor and a controller with a build-in humidity

sensor will be seen as an humidity sensor.

When one or more sensors are connected to the HRU appliance, it will ventilate according to the set conditions of

the connected sensor(s).

If multiple controllers /sensors are used, the controller / sensor that requests the highest ventilation level always

has priority.

Boost function ( ):

The boost function can be canceled at any time by pressing another button of the Wireless Controller with

humidity sensor. When the boost button is pressed again during use of the boost function, the timer is reset and

the connected ventilation device will run on ventilation level 3 again for 30 minutes. For position "Boost button"

see ®Overview operational controls page 7.

The air ﬂowquantities associated with the ventilation settings must always be set on the connected appliance

and cannot be adjusted on the Wireless Controller with humidity sensor. For ventilation settings, see the

installation manual of the relevant connected HRU appliance.

Wireless Controller with humidity sensor 616880-B

1.2 Delivery content

Check that delivered Wireless Controller with humidity sensor is complete and not damaged.

The scope of delivery includes 2 boxes; one for the Wireless Controller with humidity sensor with frame and wall

bracket and one for the USB transceiver.

The delivery content of the Wireless Controller with humidity sensor consists of the following components:

1. Wireless Controller with1.

humidity sensor

2. Frame2.

3. Wall bracket3.

4. Double-sided adhesive tape4.

5. Mounting screws5.

6. USB transceiver6.

7. Short information with QR-7.

code to on line manual

Wireless Controller with humidity sensor 616880-B Brink / 5

2 Technical speciﬁcation

2.1 General product speciﬁcation

Product description

Name: Wireless Controller with humidity sensor

Technical product speciﬁcations

Operating voltage: 3 V

Protection class: IP21

Type of battery :

CR2032.MRF Lithium (preferred manufacturer

Renata or Panasonic CR-2032/BS )

Not applicable if a permanent power connection

is used!

Frequency 868 MHz

Ambient conditions

Ambient temperature: 0 °C to 50 °C

Storage temperature: -20 °C to 60 °C

Humidity: 0% to 90%

Other: For indoor use

Max distance between USB transceiver and

Wireless Controller with humidity sensor 300 m (open ﬁeld; 1 meter height)

2.2 Environment inﬂuences

The Wireless Controller with humidity sensor should be placed and used in a space with the correct ambient

conditions for proper operation. The Wireless Controller with humidity sensor may only be mounted indoors, but

not close to a heat source, a radiator, in a extreme humid environment. The Wireless Controller with humidity

sensor may also not be exposed to direct radiation heat (sun light). The Wireless Controller with humidity sensor

may also not be mounted close to a magnetic ﬁeld. This could damage internal components.

Wireless Controller with humidity sensor 616880-B

2.3 Overview operational controls

The Wireless Controller with humidity sensor has four (capacitive) buttons (two visible and two invisible buttons).

Each button is equipped with a LED.

Button 1 - Automatic ventilation position in

accordance with build in humidity sensor

Button 2 - boost function

Button 3 - Not visible but available for "note ID"

Button 4 - Not visible but available for "note ID"

Filter/fault indication LED

Button 1 (auto)

When button 1 is operated, the HRU appliance will be set to ventilation level

1 or the HRU appliance will be ventilate automatically conform set

requirements of the build in humidity sensor; the white LED next to button 1

will ﬂash once as "button press" conﬁrmation.

Button 2 ( )

When button 2 is operated, the HRU appliance will run for 30 minutes at

ventilation level 3 (boost function) and then again at ventilation position 1;

the white LED placed next to button 2 will ﬂash once as "button press"

conﬁrmation.

Button 3 & 4

When the (not visible) buttons 3 & 4 are operated for a note ID (see ®

Connecting with USB Tranceiver (Pairing) page 13 ) the white LED placed

next to these buttons will ﬂash once as "button press" conﬁrmation.

Filter/ fault LED

This LED indicates when ﬁlter (s) must be cleaned / replaced or when a

malfunction has occurred in the connected HRU appliance.

Wireless Controller with humidity sensor 616880-B Brink / 7

Filter notiﬁcation

The ﬁlter(s) in the HRU appliance, connected to the Wireless Controller with

humidity sensor, should be cleaned or replaced when the red LED on the

Wireless Controller with humidity sensor appears.

This LED is on for 10 seconds every 3 hours or for 300 seconds if any of the

buttons are operated (Wireless Controller with humidity sensor with battery

power supply).

When the Wireless Controller with humidity sensor is equipped with a

permanent power supply (optional) this LED is permanently on.

Resetting of the ﬁlter notiﬁcation is not possible with the Wireless Controller

with humidity sensor!

Consult the manual of the device connected to the Wireless Controller with

humidity sensor for resetting ﬁlter notiﬁcation

1 = LED Filter nocaon

Fault notiﬁcation

If there is a fault in the HRU appliance, connected to the Wireless Controller

with humidity sensor, the red LED on the Wireless Controller with humidity

sensor ﬂashes with frequency of 1 Hz (1 blink per second).

This LED ﬂashes for 10 seconds every 3 hours or for 300 seconds if any of

the buttons are operated (Wireless Controller with humidity sensor with

battery power supply).

When the Wireless Controller with humidity sensor is equipped with a

permanent power supply (optional) this LED ﬂashes permanently.

See the installation instructions of the device connected to the Wireless

Controller with humidity sensor for troubleshooting for the error

notiﬁcations indicated on the Wireless Controller with humidity sensor.

1 = LED fault indicaon (ashes 1Hz)

Lost connection

When the Wireless Controller with humidity sensor lost connection with the

USB-transceiver the fault LED will also ﬂash.

The LED ﬂashes 3 times 0,5 seconds ON and 60 seconds OFF or ﬂashes for

300 seconds if any of the buttons are operated (Wireless Controller with

humidity sensor with battery power supply).

Filter and fault notiﬁcations are overruled. 1 = LED (ash 0.5 sec on - 60 sec o )

Wireless Controller with humidity sensor 616880-B

3 Assembly

3.1 Mounting Wireless Controller with humidity sensor on the wall

You should perform the step1 to step 4 to assemble the Wireless Controller with humidity sensor.

An example of a wireless controller is shown in this section, but other wireless controllers/sensors are

assembled in the same way.

Step 1

The wall bracket can be attached to a ﬂush mount electrical box (Ø 55 mm) or can be directly mounted on

the wall with supplied double sided adhesive tape. Mounting on a electrical box is only necessary when a

permanent power supply (option) is used. The Wireless Controller with humidity sensor should be placed at a

height of approximately 1.65 meters above the ﬂoor.

▪Screw or glue the wall bracket onto the wall in the▪

correct position.

Take note!

The up arrow on the wall bracket must point

upwards!

Backside wall bracket with posion

double sided adhesive tape

Step 2

Remove the plastic isolation strip from the battery.

Step 3

Click the Wireless Controller with humidity sensor (A)

together with supplied frame (B) on the wall bracket

(C).

After mounting the Wireless Controller with humidity

sensor on the wall bracket remove the foil from the

front.

Wireless Controller with humidity sensor 616880-B Brink / 9

Step 4

When the Wireless Controller with humidity sensor has been ﬁtted on

the wall the USB transceiver can be placed in the USB port of the

appliance which must be connected with the Wireless Controller with

humidity sensor. To connect the USB transceiver with HRU appliance

see ®Connecting with USB Tranceiver (Pairing) page 13,

Connecting additional RF sensor with USB Tranceiver (Pairing) page

16 .

3.2 Remove Wireless Controller with humidity sensor from wall bracket

For removing the Wireless Controller with humidity sensor from the

wall bracket grasp the front of the Wireless Controller with humidity

sensor by edges and gently pull away from wall.

An example of a wireless controller is shown in this section, but other

wireless controllers/sensors can be removed from the wall bracket in

the same way.

3.3 Connecting the AC/DC converter (option)

Warning!

At all times disconnect the 230 V. power supply when connecting the AC/DC converter.

When using the optional AC/DC converter, the wall bracket must be attached to a electrical wall box (Ø 55 mm).

Connect the optional AC/DC converter (A) with the Wireless Controller with humidity sensor (B) conform the wiring

diagram.

The following actions should be performed to connect the optional 5V AC/DC converter:

Step 1

▪Place the converter in the wall box.▪

▪The 230V power supply must be connected to the factory▪

mounted gray connectors. Strip the wire over a length of

approx. 7 mm.

Step 2

▪Screw the wall bracket on the wall box and feed the red▪

and black wires including mounted green connector

through the square hole in the in the mounting plate.

▪Take note!▪

The up arrow on the wall bracket must point upwards!

Step 3

▪After feed the red and black wire with the green▪

connector through the frame connect this to the

connector on the back side of the Wireless Controller

with humidity sensor.

▪Removal of the battery is not required but recommended.▪

AC/DC converter (230V~/5V=)

Wireless Controller with humidity

sensor

X1 = Black

X2 = Red

X3 = Brown

X4 = Blue

Wireless Controller with humidity sensor 616880-B

Indice

Altri manuali Brink Controllori

Brink

Brink Evap controller Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente