Briteq LED MINI PAR Manuale utente

USER

MANUAL

Ver 1,0

LED

P A R

M I N I

ABLE OF CONTENTS

1.1 PRODUCT INTRODUCTION

This product is designed for indoor use. Suitable applications include wash or effect

lighting for architectural, stage or nightclub applications. This product can also be installed

for use in signage and advertising using the dynamic functions available with DMX512

control. Direct input of DMX512 signal allows the units to be controlled from any DMX512

controller. This product can be operated as a single unit or in multiple units for large

applications.

The specially developed controller that allows the product to be controlled independent of

the DMX512 controllerenables the userto create andedit a widerange of customprograms.

All programs can be touch-button displayed or scheduled to START and END at scheduled

times. When programs have been created or edited in the controller, it is also possible to

trigger these programs using the DMX IN function when connected to a DMX512 controller.

1.2 PRODUCT FEATURES

LED FIXTURE

* RGB Dimmer 0-100%

* Strobe

* Automatic programs

* LCD display

* Display control'lock-out'

* Direct DMX512 input

* Independant IDaddress

* Stand-alone/ Slave

1 PRODUCT(GENERAL) 1

1PRODUCT (GENERAL)

2008.8.13

1.3 TECHNICAL SPECIFICATIONS

LED MODULE

Dimensions

LED MODULE:

Voltage

Rated Power

18pcs (6 xRED / 6x GREEN /6 x BLUE)

Weight

LED/Unit

Output/LED

Cooling

Forced air convection

240 x 210x160mm

2.5Kg

100~240V...50/60Hz

30W

1 PRODUCT(GENERAL) 2

Environment Temperature -20 ~40

2008.8.13

1.4 PHOTOMETRIC DATA

PHOTOMETRIC DATA

1 PRODUCT(GENERAL) 3

RED

2(0.23) 4(0.43) 6(0.56) 8(0.93) 10Distance(m)

(1.12Diameter(m))

715 178 89 51 34 LUX

GREEN

2(0.24) 4(0.41) 6(0.69) 8(1.02) 10Distance(m)

(1.02Diameter(m))

1086 270 121 73 51 LUX

BLUE

2(0.23) 4(0.42) 6(0.60) 8(0.88) 10Distance(m)

(1.12Diameter(m))

244 60 25 15.7 11 LUX

RGB

2(0.23) 4(0.44) 6(0.68) 8(1.01) 10Distance(m)

(1.07Diameter(m))

2040 512 229 137 96 LUX

2008.8.13

1.5 SAFETY WARNING

IMPORTANT

ALWAYS READ THE USER MANUAL BEFORE OPERATION.

PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE

PRODUCT IS THE SAME AS THE MAINS POWER SUPPLYIN YOUR

AREA.

This product must be installed by a qualified professional.

Always operate the equipment as described in the user manual.

A minimum distance of 0.5m must be maintained between the equipment and

combustible surface.

The product must always be placed in a well ventilated area.

Always make sure that the equipment is installed securely.

DO NOT stand close to the equipment and stare directly into the LED light

source.

Always disconnect the power supply before attempting and maintenance.

Always make sure that the supporting structure is solid and can support the

combined weight ofthe products.

The earth wire must always be connected to the ground.

Do not touchthe power cables if your hands are wet.

ATTENTION

This product leftthe place ofmanufacture in perfect condition. In order to

maintain this condition and for safe operation, the user must always follow the

instructions and safety warnings described in this user manual.

Avoid shaking or strong impactsto any partof the equipment.

Make sure thatall parts ofthe equipment are kept clean and free of dust.

Always make sure that the power connections are connected correct and

secure.

If there is any malfunction of the equipment, contact your distributor

immediately.

When transferring the product, it is advisable to use the original packaging in

which the productleft the factory.

Shields, lenses orultraviolet screens shall be changed if they have become

damaged to such an extent that their effectiveness is impaired.

The lamp (LED) shall be changed if it has become damaged or thermally

deformed.

1 PRODUCT(GENERAL) 42008.8.13

2.1 MOUNTING

HANGING

UPRIGHT

The LED PAR can be mounted in an upright or

sitting position usingthe supporting brackets.

The LED PAR can be mounted in a hanging position using the supporting bracket.

The bracket should be secured to the mounting truss or structure using a

standard mounting clamp. Please note that when hanging the unit a safety cable

should also be used.

@ 220V: 40 units may be connected in series

@120V: 20 units may be connected in series

The LED MODULEcan be mounted at any angle and in any

position. It is possible to further adjust the angle of the LED

MODULE using thetwo adjustment knobs located on the side of

the fixture.

2.2 POWER CONNECTIONS

2 INSTALLATION

Note: As this fixture's DMX signal cable connection had been changed to Parallel connection,

so if over 30 units to be connected, then a DMX signal amplifier is needed.

2INSTALLATION

2008.8.13

2.3 SETTING UP WITH A DMX512

CONTROLLER

2.3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING

(STAGE 1 MODE)

The figure above shows a simple DMX512

layout with thestarting address of the first

unit set at 1, with the second set at 10 and

so on... (Note that when used in this way,

the CH9 IDfunction must be inactive (CH9=0))

DMX512

CONTROLLER

Connect the DMX512controller to theunits in series.

Each unit has 9 DMX channels so the DMX Addresses should increase by increments of

9 (e.g. 1,10,19,28...)

The ID addresshas not been set so therefore when usingthe controller Ch9 must

be inactive (CH9=0 ).

Each DMX Address may be used as many times as required.

Any DMX address in the range from 001 to 512 may be used.

2.3-2 DMX512 ADDRESSING WITH ID ADDRESS (STAGE 1 MODE)

Connect the DMX512 controller to the units in series

Each unit has 9DMX channels so the DMX Addresses should increase by increments of

9 (e.g. 1,10,19,28...)

Each DMX Address may be used as many times as required.

Any DMX address in the range from 001 to 512 may be used.

Each DMX addressmay carry up to 66 separate ID addresses.

ID should be set in the menu on each unit in ascending values

(i.e. 1,2,3...)

ID addresses are accessible from Ch9 on the DMX512 controller.

Example:

2 INSTALLATION

............

DMX Addr.1 DMX Addr.10 DMX Addr.19

2008.8.13

DMX512

CONTROLLER

Example:

The figure above shows a simple DMX layout

which has usedthree units at each DMX address.

The three unitshave different ID addresses which

allows the user to collectively control the whole

group of units at that DMX address by setting

CH9 to 0, or to control each unit independently by

first selecting the DMX address and then by using

Ch9 to locatethe target IDaddress.

2 INSTALLATION

............

DMX Addr.1

ID Addr.1

DMX Addr.1

ID Addr.2

DMX Addr.1

ID Addr.3

DMX Addr.10

ID Addr.1

DMX Addr.10

ID Addr.2

DMX Addr.10

ID Addr.3

2008.8.13

3.1 BASIC

3 DISPLAY PANEL OPERATION

DOWN

ENTER UPMENU

MENU scroll through the main menu or exit from the current menu or function

ENTER Enter the currently selected menu or confirm the current function value

UP scroll 'UP' through the menu list or increase the value of the current function

DOWN scroll 'DOWN' through the menu list or decrease the value of the current function

3DISPLAY PANEL OPERATION

2008.8.13

Indice

Altri manuali Briteq Attrezzatura di illuminazione

Briteq

Briteq MICRO BEAMER RGBW Manuale utente

Briteq

Briteq Spectra 3D Laser Manuale utente

Briteq

Briteq STAGE BEAMER RGB - V1.0 Manuale utente

Briteq

Briteq MIINI COLOR 7 TC - V1.1 Manuale utente

Briteq

Briteq BT-36LI Manuale utente

Briteq

Briteq BT-GLOWPANEL Manuale utente

Briteq

Briteq BT-THEATRE 20WW Manuale utente

Briteq

Briteq BT-AKKUPOLE Manuale utente

Briteq

Briteq BT-VENUELITE 4 Manuale utente

Briteq

Briteq BT-LASER2000 RGB Manuale utente

Briteq

Briteq LED UV-GUN 60W Manuale utente

Briteq

Briteq LED Blaster 108 Manuale utente

Briteq

Briteq LED BLINDER WHITE - V1.0 Manuale utente

Briteq

Briteq LED MEGA BEAM Manuale utente

Briteq

Briteq BT-CHROMA 800 Manuale utente

Briteq

Briteq BTX 300 Beam Manuale utente

Briteq

Briteq BT-150LS Manuale utente

Briteq

Briteq BT-54L3 Manuale utente

Briteq

Briteq BT-36II Manuale utente

Briteq

Briteq LD-POWER240 Manuale utente

Briteq

Briteq BEAMSPOT1-TRIAC NW Manuale utente

Briteq

Briteq Club Laser 7 Manuale utente

Briteq

Briteq BT-THEATRE 250EZ Mk2 Manuale utente

Briteq

Briteq BTX-700SW Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente