Brivis B063047 Guida utente

Brivis Touch Controller

Installer Manual

Brivis Touch Controller Kit

Scope

Please read these instructions carefully before installing this

product. This manual covers the installation of the wall mounted

Brivis Touch Controller for the following Brivis applications:

GasDuctedHeating

Gas Ducted Heating & Refrigerated Cooling (Dual Comfort)

Evaporative Cooling

Zoning, including Brivis ZonePlus

For the installation of Brivis Heating and Cooling products please

refer to the equipment Installer Manuals.

This manual is based on Australian Standards - for all other

applications, please refer to relevant local codes and regulations.

Any deviations from these instructions may, at the discretion of

Brivis, void the warranty. As a result, the customer and/or installer

may be charged a fee for non-product warranty related call outs.

Also, note that failure to comply with these instructions may

preclude Brivis from being able to service the product.

Terminology:

Shall:Indicatesamandatoryrequirementofthismanual.

Should:Indicatesarecommendedrequirementofthismanual.

Disclaimer

IMPORTANT NOTICE: This document is a guide only. Laws, regulations and industry standards can

vary between States and Territories. Accordingly, this guide must be read in conjunction with, and

subjectto,alllaws,regulationsandindustrystandardsapplicablein theState or Territoryinwhich the

products are installed. You must ensure that the installation of the products will comply with

those laws, regulations and standards, and that the products recommendedtocustomersare

fitforthepurposeforwhichtheyareintended.

Table 1: Brivis Touch Controller Kit Brivis Part No. B063047

Contents and Description Qty

Brivis Touch Controller 1

Interface Module 1

Power Transformer 1

Power & Communication Loom 1

Plug & Screw Kit (for Brivis Touch) 1

Screw (for Interface Module) 2

Screw Driver 1

Inspect the product to ensure it matches your order. In the event of

damage or incorrect delivery, notify the supplier immediately. Brivis

accepts no responsibility for installation of damaged or incorrect

product.

Please read these installation instructions before undertaking the

installation process.

Specifications subject to change without notice.

Pictures for illustration purposes only.

The Brivis Touch Controller is compatible with selected Brivis

units only. For information on compatibility please contact Brivis.

Pre-2010 compatible Brivis heaters will have limited on-board

diagnostics.

TableofContents

1.0 Home Screen – Key Functions .................................................4

2.0 Brivis Touch Controller Installation..........................................5

2.1 Location of the Brivis Touch.....................................................5

2.2 Location of the Interface Module..............................................6

2.3 Install the Brivis Touch .............................................................6

2.5 Install Interface Module.............................................................7

2.6 Connection of Interface Module to P&C Loom ........................8

2.7 Connection of Interface Module to Appliance..........................9

3.0 System Setup.............................................................................9

3.1 Turning the System ON.............................................................9

3.2 Set Day/Time............................................................................10

3.3 Installer Setup..........................................................................11

3.4 Reset Networker ID..................................................................12

3.5 Networker Parameters.............................................................13

3.6 Cooler Parameters...................................................................13

3.7 Heater Parameters...................................................................13

3.8 System with no Zones.............................................................13

3.9 System with Zones (Inc. Brivis ZonePlus) ............................. 14

3.10 System Operation..................................................................14

3.11 Service Notification Message ...............................................14

3.12 Outdoor Temperature Sensor (Optional)..............................15

4.0 Product and Warranty Registration ........................................15

5.0 Instruct Home Owner on System Operation...........................15

6.0 Troubleshooting.......................................................................16

6.1 Power Outages.........................................................................16

7.0 Appendix ..................................................................................17

Definitions

Brivis Networker

Networker is a term used for a temperature sensing or

communicating device which communicates over two-wire bus.

There can be only one Master Networker (n01), all others must be

slaves (n02, n03 ….n10).

Brivis Touch Controller

Primary user interface with touchscreen display. Where multiple

Brivis Touch Controllers are installed, the “Master” Brivis Touch

Controller can be identified by the letter “M” displayed in the

bottom right hand corner of the screen. The Master has default

sensor identification “n01”.

The Brivis Touch Controller is a touchscreen thermostat which

communicates over two-wire bus. It is compatible with NC-3, NC-6

and N-T1 sensors.

Brivis NC-6 Networker Controller

A user interface with LCD display. The NC-6 has default sensor

identification “n01 ID00:1” (Master) and should be changed to a

slave if used on the same system as the Brivis Touch Controller.

Brivis NT-1 Remote Temperature Sensor

Zone temperature sensor with an LED that blinks during

communication with Master Brivis Touch Controller. Default NT-1

sensor identification is “n02”. Additional Brivis Touch Controllers

can be used in place of up to 3x NT-1 sensors. The NT-1 sensor

can also be used as the outdoor temperature sensing device.

Zone

One room or a group of rooms; normally selected on the basis of

usage or that have similar heating or cooling needs.

ControlledZone

A zone that is separately controlled by its own zone sensor and

zone damper. There are as many zone sensors in the home

comfort system as there are Controlled Zones.

CommonZone

A zone that is not separately controlled by its own sensor and zone

damper. It operates whenever heating or air conditioning is on,

regardless of the status of any controlled zones.

Constant Zone

A predetermined zone, typically the largest and containing the

return air grille, is designated as the Constant Zone. The Constant

Zone functions as a Common Zone only during refrigerated cooling

mode to ensure the minimum cooling airflow requirements are met.

MultiTemperatureSetPoint(MTSP)System

The zone temperature set point can be set independently across

all Touchscreens and/or Temperature Sensors.

Single Temperature Set Point (STSP) System

The zone temperature set point is the same across all

Touchscreens and/or Temperature Sensors.

1.0 Home Screen – Key Functions

Diagram 3

Evaporative Cooling Home Screen

Manual or Schedule

Operation

* Active

with MTSP & STSP

systems only

iagram 1:

Heating Home Screen

Flame

Symbol

Power

Zones Where

Fitted

Mode Indicator

Adjust Set

Temperature

Indoor

Temperature

Fan Status

Indicator

Day

Digital

Clock

M - Master

Controller

System Mode

(HEAT/COOL/EVAP)

Menu – Display

Options or Settings

Fan Select

Mode

Diagram 2:

Add-On Home Screen

2.0 Brivis Touch Controller Installation

The Brivis Touch Controller is connected to a compatible Brivis

appliance through the Interface Module. A 20m, four core, Power

& Communication Loom (P&C Loom),connects the Brivis

Touch Controller to the Interface Module. The Power

Transformer (12VDC) supplies power to the Interface Module.

Diagram 4: Connection Diagram

To connect the Brivis appliance to the Brivis Touch:

1. Determine location of the Brivis Touch.

2. Determine location of the Interface Module.

3. Install the Brivis Touch.

4. Install Interface Module.

5. Connect Interface Module to Appliance.

2.1 Location of the Brivis Touch

For proper operation the Brivis Touch must accurately monitor the

temperature in the space it controls.

Guidelines:

The Brivis Touch should be mounted:

Approximately 1.5m above floor level (ensure hole into wall

cavity is properly sealed).

Close to the centre of the living space on an internal wall.

On a section of wall that does not contain pipes, electrical wires,

antenna cables or ductwork.

The Brivis Touch should NOT be mounted:

Where it is exposed to direct sunlight or other heat sources

which may cause a false reading.

Near or in the path of supply air outlets or return air grilles.

On outside walls, near windows or doors leading to outside.

In areas with poor air circulation such as recesses or behind

doors.

Note:

Do not install the wiring with the power turned on, as the

fuse may blow, which

not be covered under warranty.

Note:

When there are multiple Brivis Touch Controllers on a

system, always ensure that the location of each is within 20m

of the Interface Module

Power & Communication

Loom, 20m (supplied)

0.75mm² figure-8 cable

(field supplied)

Appliance

(field supplied)

Power Transformer

12VDC 1.5m loom

(supplied)

Brivis

Touch

(supplied)

TW2

TW1

Interface

Module

(supplied)

Isolation

Switch

(field supplied

GPO)

2.2 Location of the Interface Module

The Interface Module shall be located within 1.5m of a 10 Amp

240 volt fixed switched socket outlet. The Brivis Touch shall be

within 20m of the Interface Module.

2.3 Install the Brivis Touch

The Brivis Touch Backing Plate must be installed prior to

mounting the Brivis Touch.

To mount the Backing Plate do the following:

1. Remove the Brivis Touch Backing Plate from the packaging.

2. Use Backing Plate as a template and mark the two Mounting

Hole centres and the Loom Access hole centre, refer to

Diagram 5.

3. Install the supplied wall Plug Kit in the Mounting Hole

locations. For drill sizes refer to Diagram 5.

4. Fasten Backing Plate with wall Plug Kit screws.

Diagram 5: Brivis Touch “Backing Plate”

To mount the “Brivis Touch”:

1. Run the supplied P&C Loom from the Touch to the

Interface Module.

2. Draw the loom from the wall cavity and feed through the

P&C Loom Access opening on the Touch Backing

Plate.

3. Connect the P&C Loom terminal (female) to the Touch

terminal (male) before mounting it on the wall, refer to

Diagram 6.

4. Push excess cable back into the wall cavity and mount

Touch onto the Backing Plate. The three Male Clips on

the Backing Plate will engage and secure the Touch,

refer to Diagram 7.

Diagram 6: Brivis Touch Controller P&C Loom Connection

Mounting Hole

Drill size

6.0mm

Mounting Hole

Drill size ø6.0mm

P&C

Loom

Access

Drill size ø13

Diagram 7: Mounting Brivis Touch to Backing Plate 2.5 Install Interface Module

The Interface Module facilitates communication between the

Brivis Touch and the Brivis appliance(s) through the P&C Loom,

and is capable of connecting up to four Brivis Touch units.

The Interface Module requires a 12VDC power supply from the

Power Transformer.

The Interface Module also has an “Isolation Switch”; a red

“Status L.E.D” indicates it is ON, refer to Diagram 8.

Diagram 8:Mounting Interface Module Power & Communication

Loom Connection,

(Any of the four ports)

Transformer

connection

Isolation

switch

Status

L.E.D

2-wire bus

connection

TW1

TW2

TW1

TW2

Male Clips

To install the Interface Module:

1. Position in an environmentally protected area where the

temperature does not exceed 70°C.

2. Locate within 1.5m of a 10 Amp 240 volt fixed switched socket

outlet.

3. Distance from Interface Module to Brivis Touch shall be no

more than 20m.

4. Mount with supplied screws as shown in Diagram 9.

Diagram 9: Mounting Interface Module on flat surface

2.6 Connection of Interface Module to P&C Loom

The Interface Module is capable of connecting up to four

Brivis Touch Controllers. The P&C Loom can be connected

to the Interface Module through any of the four ports, refer to

Diagram 10.

Diagram 10: Connection of Interface Module to P&C Loom

2.7 Connection of Interface Module to Appliance

The Interface Module has four terminal points for the

connection of the Brivis Appliance control wires TW1 &

TW2. When connecting to an appliance, use only the first

set (Set 1) of two terminals or the second set (Set 2).

Never use a mixed combination of terminals when

connecting to a single appliance. For example, a Brivis

Touch operating a Brivis Evaporative Cooler and a Brivis

Gas Heater may have the two right terminals connected

to the Heater (SET 1) and the two left terminals connected

to the Evaporative Cooler (SET 2), refer to Diagram 11.

Diagram 11: Connection of Interface Module to Appliance

For more information regarding appliance connection please

refer to the product installation manual supplied with the

appliance.

3.0 System Setup

3.1 Turning the System ON

Once the system is fully connected, it can now be turned ON in the

following sequence:

1. Mains power to heater 516 Zone Module (if connected).

2. Mains power to Heater / Evaporative Cooler / Refrigeration

appliance(s).

3. Mains power to Interface Module.

Press isolation switch on Interface Module (L.E.D on).

Once completed the Brivis Touch Controller will power up and you

will be prompted to enter the day and time.

Note:

When there is more than one Brivis appliance connected to

the Interface Module ensure that the TW1 & TW2 polarity is

correct at both ends of the 2

wire bus cable.

Note:

Do not install any wiring with the power turned on, as the

fuse may blow, which would not be covered under warranty.

TW1

To Heater

To Evaporative

Cooler

SET 2

SET 1

Note

: Once you access the MENU Screen and select a

configuration option, if no button is pressed for 60 seconds while

in that configuration screen, the Touch will exit the configuration

mode and return to normal operation; this applies to all options

other than SCHEDULE.

Indice

Altri manuali Brivis Controllori

Brivis

Brivis ZonePlus B061006 Guida utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente