Broadata Communications LB-KP8E-ICP Manuale utente

8 AND 16BUTTON

WALL PLATE ETHERNET KEYPAD

BCI reserves the right to make changes to the products described herein without

prior notice or consent. No liability is assumed as a result of their use or application.

LB-KP8E-ICP / LB-KP16E-ICP

USER MANUAL

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATION

PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be damaged by

electrical spikes,surges,electric shock,lightning strikes, etc. Use of surge proctection

system is highly recommended in order to protect and extend the life of your

equipment.

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

SAFETY INFORMATION

Do not use this device near water/liquids. This device should not be exposed to dripping and

splashing or liquids.

Clean only with dry cloth.

Do not use solvents such as paint thinners and acetone to clean external casing. Such

agents will remove any labels on the device.

Do not block any fan ventilation openings.

Do not install near any sources of intense heat such as radiation, boilers, or other equipment

that produce heat

Not intended for use/storage in close proximity of critical medical supplies such as those that

might come into direct contact with patients or medical sta.

Protect the power cord from being pinched or damaged at receptacles and the point of exit

from the device.

Only use attachment /accessories speciﬁed by manufacturer. If you have any questions

about the compatibility of an accessory, contact your dealer.

In case liquid spillage on device, unplug mains power cord and contact your dealer. Continu-

ous use in this case may result in ﬁre or electric shock.

To reduce the risk of electric shock, do not touch connectors with wet hand.

Only power with the marked voltage on the device. Any other voltage can cause ﬁre or elec-

tric shock.

Do not use the device if an abnormality occurs. If any smoke or odor becomes apparent, un-

plug the power cord and contact your dealer. Do not try to repair the device yourself.

Avoid using physically damaged devices. If your device metal housing is seriously physically

damaged, the internal components may function abnormally. Contact your dealer.

Do not install the device in an area heavy with dust or constant high humidity. Operating the

device in this case may result in ﬁre or electric shock.

Only use supplied power supply. For a list of other compatible medical grade power sup-

plies, contact your dealer.

Install this device in a secure location where it cannot be easily pushed or knocked over.

Use of this device is not suitable for use within 6 ft. of a medical patient.

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

TABLE OF CONTENTS

PRODUCT DESCRIPTION

OPERATION CONTROL AND FUNCTIONS

FRONT/REAR PANEL

TELNET COMMANDS

CONFIGURATION

SPECIFICATIONS

MAINTENANCE AND TROUBLESHOOTING

SERVICE PROCEDURE

REPLACEMENT POLICY

RETURN AND REPAIR SERVICE

LIMITED WARRANTY

1.0

2.0

2.1

3.0

4.0

5.0

5.1

5.2

6.0

7.0

8.0

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

PRODUCT DESCRIPTION

The LB-KP8E-ICP (8-Button) and LB-KP16E-ICP (16-Button) Wall Plate

Ethernet Keypad offers 8 or 16 direct macro command buttons in an

elegant decora style wall plate form factor to provide end-users an

intuitive interface to control the various control functions configured

in the Integrated Control Processor (LBC-H/O-R-ICP). Integrated PoE

functionality eliminates the need for additional power supplies by

offering the capability to remotely power the wall plate over Ethernet.

Each button is easily custom labeled to identify the button’s function.

Features include:

• 1-gang wall plate Ethernet keypad with 8 buttons (LB-KP8E-ICP)

• 2-gang wall plate Ethernet keypad with 16 buttons (LB-KP16E-ICP)

• Can be powered over Ethernet with PoE (Power over Ethernet) or DC

power supply

• Easily integrates with the Integrated Control Processor (LBC-H/O-R-

ICP)

• Extra virtual buttons are available via WebGUI conﬁguration

• Comes with relays to control peripheral device on/o

• Available with PoE function or DC power supply selection

• Supports Telnet or WebGUI control

• Supports scheduling control and settings

• Adjustable LED dim light in keypad buttons

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

OPERATION CONTROL AND FUNCTIONS

DC 5V

Relay

Out

Control

FRONT PANEL

BACK PANEL

Macro Buttons: Each button has 2 colors of LEDs adjustable from dim 0~100% and can

have up to 16 commands. Further detail settings can be found in Section

2.5

Relay Out: Connect with device that supports DC 0~24V/5A power or signal that sup

ports relay function.

Control: Connect from PC/Laptop with active internet service or Telnet or WebGUI

control with RJ-45 terminated cable. This slot supports PoE PD 48V

function which means when the connected server/Hub support PSE 48v it

can be powered without DC supply connection.

DC 5V: Plug the 5V DC power adaptor included in the package and connect to AC

wall outlet for power supply.

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

TELNET COMMANDS

COMMAND DESCRIPTION PARAMETER

IPCONFIG DISPLAYS THE CURRENT IP CONFIGURATION NONE

SIPADDR XXX.

XXX.XXX.XXX SET ETHERNET IP ADDRESS XXX=0-255

SNETMASK XXX.

XXX.XXX.XXX SET ETHERNET NET MASK

XXX=0-255

SGATEWAY XXX

XXX.XXX.XXX SET ETHERNET GATEWAY XXX=0-255

SIPMODE N SET ETHERNET IP MODE N=STATIC/DHCP

VER SHOW UNTIL FIRMWARE VERSION NONE

FADEFAULT ALL CONFIGURE AND MACRO

SET TO FACTORY DEFAULT NONE

ETH_FADEFAULT ALL ETHERNET CONFIGURE SET TO FACTORY* NONE

REBOOT SYSTEM REBOOT NONE

HELP SHOW COMMAND LIST NONE

HELP N SHOW DESCRIP OF COMMAND N: COMMAND NAME

RELAY N N1 RELAY CONTROL N(PORT)=1

N1=OPEN/CLOSE/TOGGLE

LEDBLUE N N1 LED BLUE BACKLIGHT CONTROL N(LEN NO.)~1-8

N1=% (1-100)

LEDRED N N1 LED RED BACKLIGHT CONTROL N(LEN NO.)~1-8

N1=% (1-100)

LEDBLUES N ALL BLUE LED BACKLIGHT CONTROL N=% {0-100}

LEDREDS N ALL RED LED BACKLIGHT CONTROL N=% {0-100}

LEDSHOW N LED DIMMING MODE CONTROL LEDSHOW N

N=ON/OFF/TOGGLE

BACKLIGHT N ALL LED BACKLIGHT CONTROL N=% {0-100}

KEY_PRESS N RELEASE

KEY_PRESS N HOLD KEY PRESS TRIGGER TYPE

KEY_PRESS N RELEASE

KEY_PRESS N HOLD

N=PORT NUMBER

MACRO N MACRO SETTING

MACRO RUN N N=MACRO

ID (1-16)

MACRO STOP

TELNET_TIMEOUTN SET TELNET TIMOUT ON/OFF N=ON/OFF

NOTE: ANY COMMANDS WILL NOT BE EXECUTED UNLESS FOLLOWED

BY A CARRIAGE RETURN. COMMANDS ARE CASE-SENSITIVE

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

CONFIGURATION

THE BACKGROUND

LIGHT BAR ALLOWS

USER TO INSTANT-

LY CHANGE THE

LEDS LIGHTING

PERCENTAGE

BASED ON THE

ORIGNIAL ILLUMI-

Telnet Control

Before attempting to use the Telnet control, please ensure that both the device under

control and the PC/Laptop are connected to the same active networks.

To access the Telnet control in Windows 7, click on the ‘Start’ menu and type “cmd” in

the Search ﬁeld then press enter.

Under Windows XP go to the ‘Start’ menu and click on “Run”, type “cmd” with then press

enter.

Once in the command line interface (CLI) type “telnet”, then the IP address of the unit,

then hit enter.

This will bring us into the unit which we wish to control. Type “help” to list the available

commands.

Note: Commands will not be executed unless followed by a carriage return.

Commands are case-sensitive. If the IP is changed then the IP Address required for

Telnet access will also change accordingly. CLICK ON THE

EDIT SYMBOL TO

EDIT COMMAND

SETTINGS. UP/

DOWN ARROWS

ARE TO MOVE THE

COMMAND UP OR

DOWN AND DE

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

CONFIGURATION

THE BACKGROUND

LIGHT BAR ALLOWS

USER TO INSTANT-

LY CHANGE THE

LEDS LIGHTING

PERCENTAGE

BASED ON THE

ORIGNIAL ILLUMI-

BUTTON CON

FIGURATION

ON THE TOP MENU

BAR CLICK ON CUS

TOMIZE AND THEN

CLICK ON 8/16

BUTTON KEYPAD.

WebGUI Control

On a PC/Laptop that is connected to an active network system, open a web browser

and type device’s IP address on the web address entry bar. A security page will appear

to ask for User and Password, please key in “admin” for both to enter.

Note: The Default IP setting is DHCP.

The browser will display the device’s Macro Setting, Extension Macro, Command

Settings, Schedule, Network and System Settings pages for users to control.

CLICK ON THE

EDIT SYMBOL TO

EDIT COMMAND

SETTINGS. UP/

DOWN ARROWS

ARE TO MOVE THE

COMMAND UP OR

DOWN AND DE

8-Button Wall Plate Ethernet Keypad User Manual (LB-KP8E-ICP / LB-KP16E-ICP)

CONFIGURATION

THE BACKGROUND

LIGHT BAR ALLOWS

USER TO INSTANT-

LY CHANGE THE

LEDS LIGHTING

PERCENTAGE

BASED ON THE

ORIGNIAL ILLUMI-

Macro Settings

The Background Light Bar allows user to instantly change the LEDs lighting percentage

based on the orignial illumination setting.

There are 6 Macros pre-conﬁgured as default setting for testing the Wall-Plate Control

System’s functionality. Click on Macro 1~6 to demonstrate the function of lighting LEDs.

• Macro 1: Light up the Red backlight LED with 100% brightness sequentially from 1~8

with every 500ms.

• Macro 2: Light up the Blue backlight LED with 100% brightness sequentially from

1~8 with every 500ms.

• Macro 3: Switch o all the read backlight LED with 0% brightness.

• Marco 4: Switch o all the blue backlight LED with 0% brightness.

• Marco 5: LED show mode toggle, swith o Demo Mode

• Macro 6: Light up the Blue backlight LED with 10% brightness, Switch o all the

blue backlight LED with 0% brightness, switch O & On Relay 1 with delay of

1000ms.

To disable default testing mode, set Demo Mode switch to o.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Broadata Communications Tastiera

Broadata Communications

Broadata Communications LB-KP4 Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo